Bedtime ZELDA BUNK BED FRAME Installation guide

P1 / 11
ASSEMBLY & CARE INSTRUCTION
ZELDA BUNK BED FRAME
TWO PERSONS HANDLING
V202010210401

P2 / 11
Contact your supplier
Only other tool
required is a
screwdriver (Not included)
?

P3 / 11
Safety Advice
Please read these instructions carefully before you begin, when finished
store safely for future reference.
It would be sensible to lay down a sheet or blanket on the floor in the
room you are going to assemble the product in, this will help to avoid
scratching the product and will help to protect the floor.
If the product is going to be used on a wood, laminate or tiled floor, we
would recommend the use of anti-slip pads, these are available cheaply
in most good hardware stores.
Unpack the product carefully, inspect all parts and check all the parts are
in the box remembering some parts are in the back of the headboard,
check all hardware and make sure all numbers match the Al.
Strongly recommend that children are kept out of the area where the
bed is being assembled as there are several small parts that could
present a choking hazard.
Do not use any power tools in the assemble of this bed at ANY time.
When you start to assemble the product, we recommend you put all
small parts i.e. nut, bolts etc. into a bowel, this way you're less likely to
lose any parts. Do not fully tighten bolts till your product is fully
assembled. Do not tighten the bolts fully until the bed has been
completely built.
Safety Warning
The design and construction of the base is made to only work with a
mattress on top, do not sleep on the base without a mattress.
Every 3 months re-tighten the bolts to make sure they have not worked
loose.
If for any reason you want to move the product to a different location
the bed MUST be fully dismantled first to prevent damage.
Make sure all 4 feet are in contact with the floor, if not use the
adjustment on the feet to make it happen.

A
C
E
S
X
G
O
H
IJ
K
U
Y
N
LR
P
P4 / 11
Allen key
14pcs
Ø1/4" x 30mm
Ø1/4" x 50mm
Ø4 x 30mm
Ø15 x 90mm
Ø8 x 30mm
Ø1/4" x 13mm
Plastic Cap
Ø4 x 35mm
Ø1/4" x 75mm
Ø1/4" x 100mm
24pcs
8pcs
36pcs
14pcs
80pcs
4pcs
12pcs
6pcs
12pcs
1pc
PARTS LIST
B
A
B
D
C
S
X
U
Y
No.
1
2
3
4
5
6
7
8
9
10
11
No.Picture Description Picture Description
Q.ty Q.ty
HARDWARE LIST
V
V

No. Description Q.ty
1
2
4
5
10
11
4pcs
8pcs
4pcs
24pcs
1pc
12pcs
Ø1/4" x 100mm
Ø1/4" x 75mm
Ø1/4" x 13mm
Ø8 x 30mm
Allen key
Plastic Cap
No. Description Q.ty
2
5
10
4pcs
4pcs
1pc
Ø1/4" x 75mm
Ø8 x 30mm
Allen key
STEP 1
STEP 2
10
2
5
2
5
2
X
5
5
X
1
5
2
10
11
2
5
5211
5
B
AY
1
Y
A
4
4
G
O
A
Y
11
1
B
1
10
11
B
5
P5 / 11