Beijer Electronics SUEN00403 User manual

Quick Start Guide
MELSEC QnUDE Ethernet to X2 series
SUEN00403 – Quick start Ethernet communication

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
2 (8)
Normal.dotm, 2020-09-09
1 Function and area of use
This document explains how to set up a QnUDE to communicate with X2/BoX2 over Ethernet.
2 About this Startup document
This Startup document should not be considered as a complete manual. It is an aid to be able to
Startup a normal application quickly and easily.
Use the following hardware, software, drivers and utilities in order to obtain a stable application:
In this document we have used following software and hardware
 iX Developer 2.40 SP4 or later
 X2/BoX2 series
 GX Works 3
 QnUDE CPU with built in Ethernet
For further information refer to
 Beijer Electronics knowledge database, HelpOnline
This document and other Startup documents can be obtained from our homepage.
Please use the address [e-mail] for feedback about our Quick Start
documents.
Copyright © Beijer Electronics, 2020
This documentation (below referred to as ‘the material’) is the property of Beijer Electronics. The holder or user has a non-
exclusive right to use the material.
The holder is not allowed to distribute the material to anyone outside his/her organization except in cases where the material is
part of a system that is supplied by the holder to his/her customer.
The material may only be used with products or software supplied by Beijer Electronics.
Beijer Electronics assumes no responsibility for any defects in the material, or for any consequences that might arise from the use of
the material.
It is the responsibility of the holder to ensure that any systems, for whatever applications, which is based on or includes the
material (whether in its entirety or in parts), meets the expected properties or functional requirements.
Beijer Electronics has no obligation to supply the holder with updated versions.

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
3 (8)
Normal.dotm, 2020-09-09
3 Table of Contents
1 Function and area of use ......................................................................................... 2
2 About this Startup document .................................................................................... 2
3 Table of Contents .................................................................................................. 3
4 Setting in QnUDE Ethernet communication .................................................................. 4
5 Setting in X2/BoX2 Ethernet communication................................................................. 5
Create a new project in iX Developer ................................................................... 5
Driver setting (MC Protocol) .............................................................................. 7
6 About Beijer Electronics ......................................................................................... 8
Contact us ................................................................................................... 8

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
4 (8)
Normal.dotm, 2020-09-09
4 Setting in QnUDE Ethernet communication
The following chapter describes how to setup the Ethernet communication.
Adjust the Built-in Ethernet port open settings located in PLC-Parameter.
Enter IP address, Subnet Mask and (if used) Default Gateway.
Port no. in decimal.
Select protocol UDP and set station port number (setting range: 1025 to 4999, 5010 to 65534. Do not use port
5000 to 5009 since they are used internally by the system. For multiple HMI’s connected to one controller, use
a uniques port for each HMI to reduce the workload.

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
5 (8)
Normal.dotm, 2020-09-09
5 Setting in X2/BoX2 Ethernet communication
The following chapter describes how to setup the Ethernet communication in iX Devloper using the
MC Protocol driver connecting to QnUDE.
Create a new project in iX Developer
Start iX Developer, select “Create New Project”:
Select target:

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
6 (8)
Normal.dotm, 2020-09-09
When creating a new project or adding/changing controller
Select MC Protocol:
Type path and project name:

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
7 (8)
Normal.dotm, 2020-09-09
Driver setting (MC Protocol)
Double click on “Tags”:
Select “Controllers” - “Settings…”:
Select “UDP” and “Hexadecimal”:
Type IP address and port number stated in GX Works3:
Tip!
Help about driver, click on “Help”
Press OK.

QnUDE Ethernet – X2/BoX2 series SUEN00403 2020-10
Beijer Electronics AB  a Beijer Electronics Group company
Head Office Subsidiaries
Beijer Electronics AB Click here for details
P.O. Box 426, Stora Varvsgatan 13a
SE-201 24 Malmö, SWEDEN
Telephone [phone]
Reg no. 556701-4328  VAT no SE556701432801  www.beijerelectronics.com  [e-mail]
8 (8)
Normal.dotm, 2020-07-01
6 About Beijer Electronics
Beijer Electronics is a multinational, cross-industry innovator that connects people and
technologies to optimize processes for business-critical applications. Our offer includes operator
communication, automation solutions, digitalization, display solutions and support. As experts in
user-friendly software, hardware
and services for the Industrial Internet of Things, we empower you to meet your challenges
through leading-edge solutions.
Beijer Electronics is a Beijer Group company. Beijer Group has a sale over 1.6 billion SEK in
2019 and is listed on the NASDAQ OMX Nordic Stockholm Small Cap list under the ticker
BELE. www.beijergroup.com
Contact us
Global offices and distributors
!Optional details if one wants to add local contact information in the document!
Local office Telephone E-mail
Sweden [phone] [e-mail]
China NORWAY TAIWAN
Shanghai Drammen Taipei
DENMARK SOUTH KOREA TURKEY
Roskilde Seoul Istanbul
FRANCE SWEDEN UNITED KINGDOM
Paris
Göteborg
Malmö
Stockholm
Nottingham
GERMANY USA
Nürtingen
Salt Lake City