BeiJer Korenix JetCon 1701GP-U User manual
A Beijer Group Company
JetCon 1701GP-U is an PoE injector. The JetCon 1701GP-U is an advanced and cost effective
high power PoE injector, which applies power to Ethernet RJ-45 for power devices (PDs).
JetCon1701GP-U are classified as power source equipment (PSE), providing up to 90 watts to
powered devices(PD). It could provide power for the powered deviced (PD) which compliant
IEEE 802.3af/at/bt (draft 2.0). The JetCon 1701GP-U adopts rugged metal case design to
operate in harsh environment (-40~75°C). It also IP-31 standard protection. JetCon 1701GP-U
recommend working voltage is DC 52V. (Input range: DC44~ 57 V).
Grounding JetCon 1701GP-U
There is one grounding screw on the bottom side of JetCon 1701GP-U . Connect the frame
grounding of JetCon 1701GP-U to the grounding surface to ensure safety and prevent noise
for communication interference.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the power wires loosened.
Overview
JetCon 1701GP-U
Quick Installation Guide V1.0
Package List
JetCon 1701GP-U Industrial PoE Injector
Quick Installation Guide
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 1701GP-U on the DIN rail. For
information about the DIN Rail installation, please refer to user’s manual.
Installation
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional stas are
ready to solve your problems at any time Korenix global service center's e-mail is
KoreCARE@korenix.com.
For more information and documents download please visit our website:
http://www.korenix.com/page/doc/index.aspx
Connecting to Network
Connecting the Gigabit PoE port: e port supports IEEE 802.3af/at/bt PoE standard and
e PoE port can oer 15W/30W/60W/90W power one end of an Ethernet cable into the
UTP port of JetCon 1701GP-U , while the other end is connected to the attached networking
device.
Wiring the Relay Output
e relay output contacts are in the middle of the terminal block connector as shown below.
By inserting the wires, relay output alarm will detect power fault, and form a short circuit. e
alarm relay output is “Normal Open”. For more information, please refer Manual chapter for
more detail.
Note: e relay contact only support 1A current, DC 24V. It does not recommend apply
higher voltage and current that over this specication.
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial standard.
Korenix warrants that the Product(s) shall be free from defects in materials and workmanship
for a period of ve (5) years from the date of delivery provided that the Product was properly
installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are caused
by damage resulting from force measure (such as oods, re, etc.), other external forces such as
power disturbances, over spec power input, or incorrect cabling; or the warranted Product is
misused, abused, or operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
Support
常规
JetCon 1701GP-U 是单端口快速以太网到光纤介质转换器符合802.1af/at/bt JetCon
1701GP-U具有冗余电源输入，具有電壓范围DC44〜57V 。
关于快速安装指南
“快速安装指南”旨在指导专业安装人员安装和配置JetCon 1701GP-U。 它涵盖了
帮助您避免意外问题的程序。
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
Tel:+886-2-89111000
Fax:+886-2-29123328
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000V1701GPU
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
导言
安装
Din-Rail 支架：
将JetCon 1701GP-U背面的Din-rail夹子安装在DIN导轨。有关DIN导轨安装的信息请
参考用户手册。
JetCon 1701GP-U 接地：
JetCon 1701GP-U底部有一个接地螺丝。 将JetCon 1701GP-U连接框架接地以保证安
全，防止噪音用于通信干扰。
输入电源接线：
1. 将正极和负极线插入端子块连接器上的V +和V-触点。(如下图)
2. 拧紧电线夹螺钉，防止电源线松动。
5年质保
所有科洛理思产品的设计、制造及测试都是采用较高的工业标准。科洛理思保证自
产品出货日起提供最高5 年之免费保修服务，保修期间如因零件损坏或制程不良而
导致产品故障，我们将提供免费维修服务。
然而，自然外力(火、水、雷灾)所造成的产品故障，或其它外部因素如电源干扰、
不当电源输入、不当接线等造成的损坏，不列入产品保固范围；此外，产品被误用
、未经授权的修理及修改等行为将造成保固条款失效。
注意! 请勿于电源开启时插拔接线端子，以避免产生火花造成系统损坏。
此产品保证完全符合欧盟2003年1月27日电气和电子设备危害物质限制委员会所提
出的限用指令2002/95/EC(ROHS禁令)及2011/65/EU(RoHS 2.0)。
Korenix售后服务
KoreCARE 是科洛理思科技全球服务中心，我们专业的技术人员随时准备解答您的
疑问。科洛理思全球服务中心 EMAIL: KoreCARE@korenix.com
详细说明及文件请至网站下载: http://www.korenix.com/page/doc/index.aspx
业务服务: [email protected]
官网: www.korenix.com.cn
客户服务
产品清单
JetCon 1701GP-U Gigabit PoE 供电器*1
快速安装指南*1
连接到网络
连接以太网端口：将以太网电缆的一端连接到JetCon 1701GP-U的UTP端口，另一端
连接到所连接的网络设备。
注意: 继电器触点仅支持1A电流，DC 24V。不建议使用超过本规范的更高的电压
和电流。
接线输出
继电器输出触点位于连接器端子中间，如下所示。 继电器输出报警将检测端口或电
源故障，并形成短路。 有关更多信息，请参阅手册章节了解更多详细信息。
警告: 此符号表示您必须遵守的警告
注意: 此符号表示您必须注意的重要注意事项。
注意: 推荐的输入电压为DC 52V。 (可输入范围：DC44〜57V)
