Beko METPOINT OCV User guide

EN - English
Instructions for installation and operation
METPOINT®OCV
DATA-LOG
10-044
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

Dear Customer,
Thank you very much for having chosen METPOINT®OCV DATA LOG software. Please read this
installation and operating manual carefully before installing and using the METPOINT®OCV DATA
LOG and follow our directions. Proper operation of the METPOINT®OCV DATA LOG is
guaranteed only if the instructions and directions specified are strictly observed.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

1 Contents
1Contents .................................................................................................................................................3
2General information ................................................................................................................................4
3Scope of application and proper use ......................................................................................................4
4System and function description.............................................................................................................5
5System requirements..............................................................................................................................5
6Connecting the network / notebook to METPOINT®OCV......................................................................6
7Installing and setting METPOINT®OCV DATA LOG .............................................................................7
7.1 "Settings" menu ......................................................................................................................................7
7.2 "Network" selection.................................................................................................................................8
7.3 Connection via DHCP.............................................................................................................................8
7.4 Manual network connection....................................................................................................................9
7.5 Establishing a direct connection to a notebook / PC ............................................................................10
7.6 Manual connection to a notebook / PC.................................................................................................11
8The METPOINT®OCV DATA LOG program .......................................................................................17
8.1 Installation and start of METPOINT® OCV DATA LOG .......................................................................17
8.2 Start screen ..........................................................................................................................................18
8.2.1 Display of connected devices ...............................................................................................................18
8.2.2 Language selection ..............................................................................................................................19
8.3 The LIVE function .................................................................................................................................20
8.3.1 Data diagram adaptation ......................................................................................................................22
8.4 The SCREENSHOT function................................................................................................................24
8.5 The FIRMWARE UPDATE function .....................................................................................................25
8.6 The IMPORT + VIEWER function ........................................................................................................26
8.6.1 Selection of data...................................................................................................................................27
8.6.2 The AUTOMATIC IMPORT function ....................................................................................................29
8.6.3 The SINGLE FILE IMPORT function....................................................................................................33
8.6.4 The MULTIPLE FILE IMPORT function ...............................................................................................35
8.7 Data export in EXCEL ..........................................................................................................................37
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

2 General information
Before reading the operating manual check whether you have the right manual at hand.
The operating
manual must be accessibly available at all times at the site where the
software is being used.
To ensure a secure transfer of data, the software must be installed and used solely in
accordance with the specifications in the operating manual.
Disregarding the installation and operating manual results in risk to persons, plant and
equipment.
3 Scope of application and proper use
The METPOINT®OCV DATA LOG software is used for displaying and storing the measured
values collected using METPOINT®OCV. Any use in excess of this is considered as unintended.
The manufacturer is not liable for the consequences of improper use. The operator is solely
responsible for any risk that might result.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

4 System and function description
The METPOINT®OCV DATA LOG software is used for displaying, remotely analysing and storing
the measured values collected using METPOINT®OCV.
Displaying and storing the measured values for residual oil content ascertained using METPOINT®
OCV can be done on a directly connected notebook/PC and on a notebook/PC connected via the
web.
As a result, the measurement can be tracked on the notebook/PC.
Every measured value from the current collection of data can be read. This also makes it possible
to monitor the measured values over an extended period of time.
In addition, the program provides the means for updating the measurement device software and
makes establishing an FTP connection to the device easier.
5 System requirements
Network: .NET Framework 4 (if not present, is automatically installed
before the program)
Storage space for network 280 MB
Supported operating systems Microsoft Windows XP
Microsoft Windows Vista
Microsoft Windows 7
Minimum hardware Suitable for the particular operating system used
Storage space for software: 25 MB
Interface: Ethernet interface
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

6 Connecting the network / notebook to METPOINT®OCV
Connect the interface for your network / notebook to the METPOINT®OCV (1) Ethernet interface
intended for it using a corresponding network cable.
It should be noted that the connection from the device to the notebook is made using a
crossover cable. The connection to a network is made with a simple patch cable.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

7 Installing and setting METPOINT®OCV DATA LOG
This chapter describes the connections and settings that must be made for the METPOINT®OCV
DATA LOG software to operate properly.
NOTE!
Administrator rights are mandatory for installing the METPOINT®OCV DATA LOG
software. Please make sure that you are provided with the appropriate permissions.
Please call on the assistance of appropriately trained and authorised technical staff.
7.1 "Settings" menu
The settings that are required for connecting METPOINT®OCV into an in-house network or for
connecting directly to a PC or notebook are made in this menu.
As a rule, two options are available here:
•automatic connection by DHCP
•manual configuration
Note to the network administrator
Communication via a network between METPOINT®OCV and a PC works with the
METPOINT®OCV DATA LOG software only if both are in the same subnet. You can
find out in the manual for your router whether and how the forwarding function is
executed in your router.
Requisite firewall settings:
HTTP: Enable port 1111 (in- and outbound)
in addition: Enable port 5000 (TCP) for device update
FTP connection: Port 21 (TCP) (outbound for passive only)
Port 21 (TCP) (in- and outbound for active)
It is also possible to manually establish an FTP connection to a device in another
subnet. Please contact your network administrator.
"metpoint" for the user name and "logfiles" for the password must be specified as the
login data.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

7.2 "Network" selection
Select the desired method in the menu sub-item NETWORK:
•Automatic IP address assignment via DHCP
•Manual IP address assignment.
To use this selection, go to main menu SETTINGS and then select NETWORK.
7.3 Connection via DHCP
If connection via DHCP is selected, no additional settings are required. This is based on the
prerequisite that the connected network has a DHCP server.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

7.4 Manual network connection
Here, the network connection data must be entered manually. The following entries are required:
•IP address
•Net mask
•Gateway address
It must be ensured that different IP addresses are assigned to all devices in the
network. However, the network portion of the IP address must be identical for all
devices that communicate with each other within a network.
NOTE!
Please call on the assistance of appropriately trained and authorized IT specialists.
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]

7.5 Establishing a direct connection to a notebook / PC
The connection from the device to the notebook is established using a crossover cable.
A direct connection to a notebook can also be established by means of manual configuration or
automatic address assignment via DHCP (Auto-IP).
mdi - Manufacturers Distributor, Inc Phone: (727) 835 - 0670 | Fax: (813) 571 – 0422 www.BekoSales.com | [email protected]