Beko CCFM4582B User manual

58 9976 0000/AA
Refrigerator
User manual
CCFM4582B - CCFM4582S - CCFM4582W
CFG4582S - CFG4582B - CFG4582W
EN /

A
A
A
C
SUPPLIER’S NAME MODEL IDENTIFIER (*)
INFORMATION
C
The model information as stored in the product data base
can be reached by entering following website and searching
for your model identifier (*) found on energy label.
https://eprel.ec.europa.eu/
Please read these instructions first before using your appliance
Thank you for choosing a Beko appliance.
Please take some time to read this user manual before using your appliance, to
ensure you know how to safely operate the controls and functions.
Carefully follow all unpacking and installation instructions to ensure the
appliance is correctly connected and fitted prior to use.
Please write your product model and serial number on the last page of this
user manual, and store in a safe location close to the appliance for easy future
reference.
This user manual may also be applicable for several other models. Differences
between models will be listed.
If you have any questions or concerns, please call our Customer Service Team
or find help and information online at www.beko.co.uk
The following symbols are used in the user guide:
Hazard that may result in death or injury.
NOTICE A hazard that may cause material damage to the product or its
surroundings
Important information or useful tips on operation.
Read the user manual.
Risk of fire / Flammable materials

EN
3
1 Your refrigerator 4
2 Warnings 5
Electrical requirements...........................6
Warning! This appliance must be
earthed..........................................................6
Energy saving tips..................................... 7
Compliance with WEEE Directive and
Disposing of the Waste Product: .......8
Compliance with rohs directive: .........8
Package information................................8
3 Installation 9
Points to be paid attention to when
the relocation of the refrigerator.......9
Electrical connection .............................10
Disposing of the packaging.................10
Disposing of your old refrigerator ....10
Placing and Installation......................... 11
Changing the illumination lamp ....... 11
Adjusting the legs................................... 11
4 Preparation 12
Reversing the doors...............................13
5 Using your appliance 14
Cooling .........................................................14
Storing Frozen Food ...............................15
Freezing Fresh Food...............................15
Placing the food.......................................16
Defrosting of the appliance ................16
Blue light/HarvestFresh.......................16
6 Maintenance and
cleaning 17
Protection of plastic surfaces ...........17
7 Troubleshooting 18

EN
4
1Your refrigerator
7
8
10
2
3
4
9
11
13
5
6
*
*
12
1. Temperature setting control
2. Cabinet shelves
3. Defrost water collection channel
4. Salad crisper
5. Freezer fan
6. Frozen food storage drawers
7. Adjustable feet
8. Dairy compartment
9. Egg tray
10. Door shelves
11. Fridge compartment
12. Freezer compartment
13. Fan
C Fgures that take place n ths nstructon manual are schematc and may not
correspond exactly wth your product. If the subject parts are not ncluded n the
product you have purchased, then t s vald for other models.
Congratulations on your choice a Beko quality Appliance which has been
designed to give you service for many years.

EN
5
2Warnings
• Do not connect your
appliance to the electricity
supply until all packing and
transit protectors have been
removed.
• If transported horizontally
leave to stand upright for at
least 4 hours before switching
on to allow compressor oil to
settle
• If you are discarding an old
refrigerator with a lock or latch
fitted to the door, disable the
lock/latch, ensure that it is left
in a safe condition to prevent
the entrapment of young
children.
• This fridge/freezer must
only be used for its intended
purpose i.e the storing and
freezing of edible foodstuff.
• Do not dispose of the
appliance on a fire. At Beko,
the care and protection
of our environment is an
ongoing commitment. This
appliance which is among
the latest range introduced
is particularly environment
friendly. Your appliance
contains non CFC / HFC
natural substances in the
cooling system (Called
R600a) and in the insulation
(Called cyclopentane) which
are potentially flammable if
exposed to fire. Therefore,
take care not to damage, the
cooling circuit / pipes of the
appliance in transportation
and in use. In case of damage
do not expose the appliance
to fire or potential ignition
source and immediately
ventilate the room where the
appliance is situated.
• We suggest you contact your
local authority for disposal
information and facilities
available.
• To obtain the best possible
performance and trouble free
operation from your appliance
it is very important to carefully
read these instructions.
• On delivery, check to make
sure that the product is not
damaged and that all the parts
and accessories are in perfect
condition.
• Ensure that the plug remains
readily accessible. Do not use
multiple adapter or extension
cable.
• Failure to observe these
instructions may invalidate
your right to free service
during the guarantee period.
• Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
• Do not damage the refrigerant
circuit.
• Do not use electrical
appliances inside the food
storage compartments of the
appliance, unless they are of
the type recommended by the
manufacturer.

EN
6
• We suggest you keep these
instructions in a safe place for
easy reference.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory
or mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and understand the
hazards involved. Children
shall not play with the
appliance. Cleaning and user
maintenance shall not be
made by children without
supervision.
• Children should be supervised
to ensure that they do not
play with the appliance.
Electrical requirements
Before you insert the plug into
the wall socket make sure that
the voltage and the frequency
shown on the rating plate inside
the appliance corresponds to
your electricity supply.
Rating label is on the left hand
side of fridge inner liner.
We recommend that this
appliance be connected to the
mains supply via a suitable
switched and fused socket. The
appliance must be positioned
so that the plug is accessible.
WARNING:
When positioning the
appliance ensure the supply
cord is not trapped or damaged.
Should the mains lead of the
appliance become damaged or
should it need replacing at any
time, it must be replaced by a
special purpose made mains
lead which can only be obtained
from a Beko authorised service
agent.
Warning! This appliance
must be earthed
If the fitted moulded plug is
not suitable for your socket,
then the plug should be cut
off and an appropriate plug
fitted. Destroy the old plug
which is cut off as a plug with
bared cord could cause a shock
hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this
appliance incorporates a 13
A fuse. Should the fuse need
to be replaced an ASTABEAB
approved BS 1362 fuse of the
same rating must be used. Do
not forget to refit the fuse
cover. In the event of losing the
fuse cover the plug must not be
used until a replacement fuse
cover has been fitted.
Colour of the replacement
fuse cover must be the same
colour as that visible on the pin
face of the plug. Fuse covers
are available from any good
electrical store.

EN
7
Important! Fitting A
Different Plug
1. As the colours of the wires
in the mains lead of this
appliance may not correspond
with the coloured markings
identifying the terminals in
your plug proceed as follows:
(See diagram).
2. Connect the green-yellow
or green (Earth) wire to the
terminal in the plug marked
‘E’ or with the symbol or
coloured green and yellow or
green.
3. Connect the blue (Neutral)
wire to the terminal in the plug
marked ‘N’ or coloured black.
4. Connect the brown (Live) wire
to the terminal in the plug
marked ‘L’ or coloured red.
5. With alternative plugs a 13
A fuse must be fitted either
in the plug or adaptor or in
the main fuse box. If in doubt
contact a qualified electrician.
Energy saving tips
1. Ensure your appliance is
installed in a well ventilated
area.
2. Ensure the time between
buying chilled/frozen food
and placing them in your
appliance is kept at minimum,
particularly in summer. We
recommend you use a cool
bag or a special carrier bag to
carry perishable food.
3. Do not leave the door (s) of
your appliance open longer
than necessary and ensure
they are closed properly after
each opening.
4. Defrost frozen food in the
fridge compartment, so that
frozen food acts as an ice pack
to assist cooling in the fridge.
5. Energy consumption of this
appliance is measured while
freezer compartment is
loaded without use of top
shelf lid and the drawers
except the bottom drawer.
It is advised that freezer
compartment is loaded
without use of drawers except
the bottom drawer in order
to achieve maximum loading
capacity.
FITTED WITH
BS 1362 13A FUSE ALWAYS
FIT BS 1362 REPLACEMENT
CARTRIDGE FUSE
GREEN &
YELLOW
OR
GREEN
N
BLUE
OR
BLACK
L
BROWN
OR
RED
22mm.
6mm.
6mm.
6mm. 32mm.
12mm.
FUSE
CORD GRIP

EN
8
Compliance with WEEE
Directive and Disposing of
the Waste Product:
This product complies
with EU WEEE
Directive (2012/19/
EU). This product
bears a classification
symbol for waste
electrical and electronic
equipment (WEEE).This product
has been manufactured with
high quality parts and materials
which can be reused and are
suitable for recycling. Do not
dispose of the waste product
with normal domestic and other
wastes at the end of its service
life. Take it to the collection
center for the recycling of
electrical and electronic
equipment. Please consult your
local authorities to learn about
these collection centers.
Compliance with rohs
directive:
The product you have
purchased complies with EU
RoHS Directive (2011/65/EU).
It does not contain harmful and
prohibited materials specified
in the Directive.
Package information
Packaging materials of the
product are manufactured
from recyclable materials in
accordance with our National
Environment Regulations. Do
not dispose of the packaging
materials together with the
domestic or other wastes. Take
them to the packaging material
collection points designated by
the local authorities.

EN
9
3Installation
BPlease remember that the
manufacturer shall not be held
liable if the information given in the
instruction manual is not observed.
Points to be paid attention
to when the relocation of
the refrigerator
1. Your refrigerator should be
unplugged.Before transportation of
your refrigerator, it should be emptied
and cleaned.
2. Before it is re-packaged,
shelves, accessories, crisper, etc.
inside your refrigerator should be
fixed with adhesive tape and secured
against impacts. Package should be
bound with a thick tape or sound
ropes and the transportation rules
on the package should be strictly
observed.
3. Original packaging and foam
materials should be kept for future
transportations or moving.
Check the following before you
start to use your refrigerator:
1. Attach 2 plastic wedges as
illustrated below. Plastic wedges
are intended to keep the distance
which will ensure the air circulation
between your refrigerator and the
wall. (The picture is drawn up as a
representation and it is not identical
with your product.)
2. Clean the interior of the
refrigerator as recommended in the
“Maintenance and cleaning” section.
The condenser of your appliance is located on the back as shown below. In order
to achieve better energy efficiency with lower energy consumption, please pull the
condenser towards yourself as illustrated in picture below.
*may not be available in all models
PULL
PULL
better energy
efficiency
initial position
MİN
55 mm

EN
10
3. Connect the plug of the
refrigerator to the wall socket. When
the fridge door is opened, fridge
internal lamp will turn on.
4. When the compressor starts to
operate, a sound will be heard. The
liquid and gases sealed within the
refrigeration system may also give
rise to noise, even if the compressor
is not running and this is quite normal.
5. Front edges of the refrigerator
may feel warm. This is normal. These
areas are designed to be warm to
avoid condensation.
6. Your product requires adequate
air circulation to function efficiently.
If the product will be placed in an
alcove, remember to leave at least 5
cm clearance between the product
and the ceiling, rear wall and the side
walls.
7. If the product will be placed
in an alcove, remember to leave at
least 5 cm clearance between the
product and the ceiling, rear wall and
the side walls. Check if the rear wall
clearance protection component is
present at its location (if provided
with the product). If the component
is not available, or if it is lost or fallen,
position the product so that at least
5 cm clearance shall be left between
the rear surface of the product and
the wall of the room. The clearance
at the rear is important for efficient
operation of the product.
Electrical connection
Connect your product to a grounded
socket which is being protected by a
fuse with the appropriate capacity.
Important:
The connection must be in
compliance with national regulations.
• The power plug must be easily
accessible after installation.
• Electrical safety of your refrigerator
shall be guaranteed only if the earth
system in your house complies with
standards.
• The voltage stated on the label
located at left inner side of your
product should be equal to your
network voltage.
• Extension cables and multi plugs
must not be used for connection.
BA damaged power cable must be
replaced by a qualified electrician.
BProduct must not be operated
before it is repaired! There is the risk
of electric shock!
Disposing of the packaging
The packing materials may be
dangerous for children. Keep the
packing materials out of the reach
of children or dispose of them by
classifying them in accordance with
the waste instructions stated by your
local authorities. Do not throw away
with regular house waste, throw away
on packaging pick up spots designated
by the local authorities.
The packing of your refrigerator is
produced from recyclable materials.
Disposing of your old
refrigerator
Dispose of your old refrigerator
without giving any harm to the
environment.
• You may consult your authorized
dealer or waste collection center of
your municipality about the disposal
of your refrigerator.

EN
11
Adjusting the legs
If your refrigerator is unbalanced;
You can balance your refrigerator
by turning its front legs as illustrated
in the figure. The corner where the
leg exists is lowered when you turn
in the direction of black arrow and
raised when you turn in the opposite
direction. Taking help from someone
to slightly lift the refrigerator will
facilitate this process.
Changing the illumination
lamp
To change the Bulb/LED used for
illumination of your refrigerator, call
your AuthorisedService.
The lamp(s) used in this appliance
is not suitable for household room
illumination. The intended purpose
of this lamp is to assist the user to
place foodstuffs in the refrigerator/
freezer in a safe and comfortable
way.The lamps used in this appliance
have to withstand extreme physical
conditions such as temperatures
below -20 °C.
(only chest and upright freezer)
Before disposing of your refrigerator,
cut out the electric plug and, if there
are any locks on the door, make them
inoperable in order to protect children
against any danger.
Placing and Installation
If the entrance door of the room
where the refrigerator will be installed
is not wide enough for the refrigerator
to pass through, then carefully remove
the doors of your refrigerator and pass
it sideways through the door.
1. Install your refrigerator to a
place that allows ease of use.
2. Keep your refrigerator away
from heat sources, humid places and
direct sunlight.
3. There must be appropriate air
ventilation around your refrigerator
in order to achieve an efficient
operation. If the refrigerator is to be
placed in a recess in the wall, there
must be at least 5 cm distance with
the ceiling and at least 5 cm with the
wall. Do not place your product on the
materials such as rug or carpet.
4. Place your refrigerator on an
even floor surface to prevent jolts.
Important: Care must be taken
while cleaning / carrying the
appliance to avoid touching the
bottom of the condenser metal wires
at the back of the appliance as you
might injure your fingers and hands.
Important:This appliance is not
designed for stacking with any other
appliance. When positioning your
appliance, take care not to damage
your flooring, pipes,wall coverings etc.
Important: Make sure that mains
cableis notcaughtunder theappliance
during and after carrying / moving the
appliance, to avoid the mains cable
becoming cut or damaged
Beko declines to accept any liability
should the instructions not be
followed.

EN
12
4Preparation
• For a freestanding appliance;
‘this refrigerating appliance is not
intended to be used as a built-in
appliance.
• Your refrigerator should be installed
at least 30 cm away from heat
sources such as hobs, ovens, central
heater and stoves and at least 5
cm away from electrical ovens and
should not be located under direct
sunlight.
• This appliance is equipped with
'Freezer Guard' which ensures that
at the advised setting [4 - four on
the control] the frozen food in the
freezer will not defrost even if the
ambient temperature falls as low
as -15 °C. So you may then install
your appliance in a garage or an
unheated room without having
to worry about frozen food in the
freezer being spoilt. However at low
ambient temperatures mentioned
above,fridge contents are likely to
freeze,so check and consume food
in the fridge accordingly. When the
ambient temperature returns to
normal, you may change the setting
to suit your needs.
• Please make sure that the interior
of your refrigerator is cleaned
thoroughly.
• If two refrigerators are to be
installed side by side, there should
be at least 2 cm distance between
them.
• When you operate your refrigerator
for the first time, please observe the
following instructions during the
initial six hours.
• The door should not be opened
frequently.
• It must be operated empty without
any food in it.
• Do not unplug your refrigerator. If
a power failure occurs out of your
control, please see the warnings in
the “Recommended solutions for
the problems” section.
• Original packaging and foam
materials should be kept for future
transportations or moving.
• The baskets/drawers that are
provided with the chill compartment
must always be in use for low energy
consumption and for better storage
conditions.
• Food contact with the temperature
sensor in the freezer compartment
may increase energy consumption
of the appliance. Thus any contact
with the sensor(s) must be avoided.
• In some models, the instrument
panel automatically turns off 5
minutes after the door has closed.
It will be reactivated when the door
has opened or pressed on any key.
• Due to temperature change as
a result of opening/closing the
product door during operation,
condensation on the door/body
shelves and the glass containers is
normal.
• Since hot and humid air will not
directly penetrate into your product
when the doors are not opened,
your product will optimize itself in
conditions sufficient to protect your
food. Functions and components
such as compressor, fan, heater,
defrost, lighting, display and so on
will operate according to the needs
to consume minimum energy under
these circumstances.

EN
13
Reversing the doors
Proceed in numerical order
1
3
2
67
8
5
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Scan to watch video showing how
to reverse doors.

EN
14
5Using your appliance
The operating temperature is
regulated by the temperature control.
Warm Cold
1 2 3 4 5
(Or) Min. Max.
1=Lowest cooling setting
(Warmest setting).
5=Highest cooling setting (Coldest
setting).
The average temperature inside the
fridge should be around +5°C.
Please choose the setting according
to the desired temperature.
Please note that there will be
different temperatures in the cooling
area.
The coldest region is immediately
above the vegetable compartment.
The interior temperature also
depends on ambient temperature,
the frequency with which the door is
opened and the amount of foods kept
inside.
Frequently opening the door causes
the interior temperature to rise.
For this reason, it is recommended
to close the door again as soon as
possible after use.
The interior temperature of your
refrigerator changes for the following
reasons;
• Seasonal temperatures,
• Frequent opening of the door and
leaving the door open for long
periods,
• Food put into the refrigerator
without cooling down to the room
temperature,
• The location of the refrigerator in
the room (e.g. exposing to sunlight).
• You may adjust the varying interior
temperature due to such reasons
by using the thermostat.
Cooling
Food storage
The frdge compartment s for the
short-term storage of fresh food and
drnks.
Store mlk products n the ntended
compartment n the cooler/freezer.
Bottles can be stored n the bottle
holder or n the bottle shelf of the
door.
Raw meat s best kept n a
polyethylene bag n the compartment
at the very bottom of the cooler/
freezer.
Allow hot foods and beverages to
cool to room temperature pror to
placng them n the cooler/freezer.
• Attenton
Store concentrated alcohol only
standng uprght and tghtly closed.

EN
15
• Attenton
Do not store explosve substances or
contaners wth flammable propellant
gases (canned cream, spray cans etc.)
n the freezer. There s a danger of
exploson.
Storing Frozen Food
Prepacked commercally frozen
food should be stored n accordance
wth the frozen food manufacturer’s
nstructons for a frozen food
storage compartment.
To ensure that the hgh qualty
acheved by the frozen food
manufacturer and the food retaler s
mantaned, the followng should be
remembered:
1. Put packets in the freezer as
quickly as possible after purchase.
2. Ensure that contents are
labelled and dated.
3. Do not exceed “Use By”, “Best
Before” dates on the packaging.
If there s a power falure do not
open the door. Frozen food should not
be affected f the falure lasts for less
than 20 hrs. If the falure s longer,
then the food should be checked and
ether eaten mmedately or cooked
and then re-frozen.
Freezing Fresh Food
Please observe the followng
nstructons to obtan the best results.
Do not freeze too large a quantty at
any one tme. The qualty of the food
s best preserved when t s frozen
rght through to the core as quckly as
possble.
Do not exceed the freezng capacty
of your applance n 24 h whch s
4 kg (8.8 lb)Placng warm food nto
the freezer compartment causes the
refrgeraton compressor to operate
contnuously untl the food s frozen
sold. Ths can temporarly lead to
excessve coolng of the refrgeraton
compartment.When freezng fresh
food turn the thermostat knob
towards MAX. Small quanttes
of food up to 1/2 kg. (1 lb) can be
frozen wthout havng to rotate the
temperature control knob.
You may place fresh food to be
frozen n any part of the freezer.
Take specal care not to mx already
frozen food and fresh food.
Placing the food
Egg tray Egg
Fridge
compartment
shelves
Food in pans,
covered plates
and closed
containers
Fridge
compartment
door shelves
Small and
packaged food or
drinks (such as
milk, fruit juice
and beer)
Crisper Vegetables and
fruits

EN
16
Blue light/HarvestFresh
*May not be available in all models
For the blue light,
Fruits and vegetables stored in
the crispers that are illuminated
with a blue light continue their
photosynthesis by means of the
wavelength effect of blue light and
thus preserve their vitamin content.
ForHarvestFresh,
Fruits and vegetables stored
in crispers illuminated with the
HarvestFresh technology preserve
their vitamins for a longer time thanks
to the blue, green, red lights and dark
cycles, which simulate a day cycle.
If you open the door of the
refrigerator during the dark period
of the HarvestFresh technology, the
refrigerator will automatically detect
this and enable the blue-green or red
light to illuminate the crisper for your
convenience. After you have closed
the door of the refrigerator, the dark
period will continue, representing the
night time in a day cycle.
Defrosting of the appliance
The applance defrosts
automatcally.
Check regularly to see if the drain
pipe is clogged or not and clear it with
the stick in the hole when necessary.

EN
17
6Maintenance and cleaning
ANever use gasoline, benzene or
similar substances for cleaning
purposes.
BWe recommend that you unplug the
appliance before cleaning.
BNever use any sharp abrasive
instrument, soap, household
cleaner, detergent and wax polish
for cleaning.
CUse lukewarm water to clean the
cabinet of your refrigerator and wipe
it dry.
CUse a damp cloth wrung out in
a solution of one teaspoon of
bicarbonate of soda to one pint of
water to clean the interior and wipe
it dry.
BMake sure that no water enters the
lamp housing and other electrical
items.
BIf your refrigerator is not going to
be used for a long period of time,
unplug the power cable, remove all
food, clean it and leave the door ajar.
CCheck door seals regularly to ensure
they are clean and free from food
particles.
ATo remove door racks, remove all the
contents and then simply push the
door rack upwards from the base.
ANever use cleaning agents or water
that contain chlorine to clean the
outer surfaces and chromium coated
parts of the product. Chlorine causes
corrosion on such metal surfaces.
ADo not use sharp, abrasive tools,
soap, household cleaning agents,
detergents, kerosene, fuel oil,
varnish etc. to prevent removal and
deformation of the prints on the
plastic part. Use lukewarm water
and a soft cloth for cleaning and
then wipe it dry.
Protection of plastic
surfaces
CDo not put the liquid oils or oil-
cooked meals in your refrigerator
in unsealed containers as they
damage the plastic surfaces of your
refrigerator. In case of spilling or
smearing oil on the plastic surfaces,
clean and rinse the relevant part
of the surface at once with warm
water.

EN
18
7Troubleshooting
Check this list before contacting the
service. Doing so will save you time
and money. This list includes frequent
complaints that are not related to
faulty workmanship or materials.
Certain features mentioned herein
may not apply to your product.
The refrigerator is not working.
• The power plug is not fully settled.
>>> Plug it in to settle completely
into the socket.
• The fuse connected to the socket
powering the product or the main
fuse is blown. >>> Check the fuses.
Condensation on the side wall of
the cooler compartment (MULTI
ZONE, COOL, CONTROL and FLEXI
ZONE).
• The door is opened too frequently
>>> Take care not to open the
product’s door too frequently.
• The environment is too humid. >>>
Do not install the product in humid
environments.
• Foods containing liquids are kept
in unsealed holders. >>> Keep the
foods containing liquids in sealed
holders.
• The product’s door is left open. >>>
Do not keep the product’s door open
for long periods.
• The thermostat is set to too
low temperature. >>> Set
the thermostat to appropriate
temperature.
Compressor is not working.
• In case of sudden power failure
or pulling the power plug off and
putting back on, the gas pressure
in the product’s cooling system is
not balanced, which triggers the
compressor thermic safeguard.
The product will restart after
approximately 6 minutes. If the
product does not restart after this
period, contact the service.
• Defrosting is active. >>> This
is normal for a fully-automatic
defrosting product. The defrosting is
carried out periodically.
• The product is not plugged in. >>>
Make sure the power cord is plugged
in.
• The temperature setting is incorrect.
>>> Select the appropriate
temperature setting.
• The power is out. >>> The product
will continue to operate normally
once the power is restored.
The refrigerator’s operating noise
is increasing while in use.
• The product’s operating
performance may vary depending on
the ambient temperature variations.
This is normal and not a malfunction.
The refrigerator runs too often or
for too long.
• The new product may be larger than
the previous one. Larger products
will run for longer periods.
• The room temperature may be
high. >>> The product will normally
run for long periods in higher room
temperature.
• The product may have been recently
plugged in or a new food item is
placed inside. >>> The product
will take longer to reach the set

EN
19
temperature when recently plugged
in or a new food item is placed inside.
This is normal.
• Large quantities of hot food may
have been recently placed into the
product. >>> Do not place hot food
into the product.
• The doors were opened frequently
or kept open for long periods. >>>
The warm air moving inside will
cause the product to run longer. Do
not open the doors too frequently.
• The freezer or cooler door may be
ajar. >>> Check that the doors are
fully closed.
• The product may be set to
temperature too low. >>> Set the
temperature to a higher degree and
wait for the product to reach the
adjusted temperature.
• The cooler or freezer door washer
may be dirty, worn out, broken or
not properly settled. >>> Clean or
replace the washer. Damaged / torn
door washer will cause the product
to run for longer periods to preserve
the current temperature.
The freezer temperature is very
low, but the cooler temperature is
adequate.
• The freezer compartment
temperature is set to a very low
degree. >>> Set the freezer
compartment temperature to a
higher degree and check again.
The cooler temperature is very
low, but the freezer temperature
is adequate.
• The cooler compartment
temperature is set to a very low
degree. >>> Set the freezer
compartment temperature to a
higher degree and check again.
The food items kept in cooler
compartment drawers are frozen.
• The cooler compartment
temperature is set to a very low
degree. >>> Set the freezer
compartment temperature to a
higher degree and check again.
The temperature in the cooler or
the freezer is too high.
• The cooler compartment
temperature is set to a very high
degree. >>> Temperature setting
of the cooler compartment has an
effect on the temperature in the
freezer compartment. Wait until the
temperature of relevant parts reach
the sufficient level by changing the
temperature of cooler or freezer
compartments.
• The doors were opened frequently
or kept open for long periods.
>>> Do not open the doors too
frequently.
• The door may be ajar. >>> Fully
close the door.
• The product may have been recently
plugged in or a new food item is
placed inside. >>> This is normal.
The product will take longer to reach
the set temperature when recently
plugged in or a new food item is
placed inside.
• Large quantities of hot food may
have been recently placed into the
product. >>> Do not place hot food
into the product.
Shaking or noise.
• The ground is not level or durable.
>>> If the product is shaking when
moved slowly, adjust the stands to
balance the product. Also make sure
the ground is sufficiently durable to
bear the product.

EN
20
• Any items placed on the product
may cause noise. >>> Remove any
items placed on the product.
The product is making noise of
liquid flowing, spraying etc.
• The product’s operating principles
involve liquid and gas flows. >>>
This is normal and not a malfunction.
There is sound of wind blowing
coming from the product.
• The product uses a fan for the
cooling process. This is normal and
not a malfunction.
There is condensation on the
product’s internal walls.
• Hot or humid weather will increase
icing and condensation. This is
normal and not a malfunction.
• The doors were opened frequently
or kept open for long periods.
>>> Do not open the doors too
frequently; if open, close the door.
• The door may be ajar. >>> Fully
close the door.
There is condensation on the
product’s exterior or between the
doors.
• The ambient weather may be
humid, this is quite normal in humid
weather. >>> The condensation
will dissipate when the humidity is
reduced.
The interior smells bad.
• The product is not cleaned regularly.
>>> Clean the interior regularly
using sponge, warm water and
carbonated water.
• Certain holders and packaging
materials may cause odour. >>>
Use holders and packaging materials
without free of odour.
• The foods were placed in unsealed
holders. >>> Keep the foods in
sealed holders. Micro-organisms
may spread out of unsealed food
items and cause malodour. Remove
any expired or spoilt foods from the
product.
The door is not closing.
• Food packages may be blocking
the door. >>> Relocate any items
blocking the doors.
• The product is not standing in full
upright position on the ground. >>>
Adjust the stands to balance the
product.
• The ground is not level or durable.
>>> Make sure the ground is level
and sufficiently durable to bear the
product.
The vegetable bin is jammed.
• The food items may be in contact
with the upper section of the
drawer. >>> Reorganize the food
items in the drawer.
If The Surface Of The Product Is
Hot.
• High temperatures may be observed
between the two doors, on the side
panels and at the rear grill while
the product is operating. This is
normal and does not require service
maintenance!Be careful when
touching these areas.
AWARNING:
Iftheproblem persistsafterfollowing
theinstructions inthissection, contact
your vendor or an Authorised Service.
Do not try to repair the product.