Beko WRE6511BWW User manual

WRE6511BWW
EN CZ SK
Plně automatická pračka
Návod k používání
2820670910_B
Automatická pračka
Používateľská príručka
Washing Machine
User Manual

3/ EN Washing Machine / User’s Manual
1 Important nstructons for safety and envronment
This section contains safety instructions that will help protect from risk of personal injury or proper-
ty damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by persons whose physical,
sensory or mental capabilities were not fully developed or who lack experience and knowledge
provided that they are supervised or trained on the safe usage of the product and the risks it
brings out. Children must not play with the product. Cleaning and maintenance works should not
be performed by children unless they are supervised by someone.
• Children of less than 3 years should be kept away unless continuously supervised.
• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machi-
ne will cause electrical parts to overheat. This will cause problems with your product.
• If the product has a failure, it should not be operated unless it is repaired by the Authorized
Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering on after a power interrup-
tion. If you wish to cancel the programme, see "Cancelling the programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the
grounding installation made by a qualified electrician. Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local
regulations.
• The water supply and draining hoses must be securely fastened and remain undamaged.
Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water in the drum. Otherwise,
risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open just a few
minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the
door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by
grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing machines only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and repairing proce-
dures.
• Always have the installation and repairing procedures carried out by the Authorized Service
Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried
out by unauthorized persons.
• If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a
similarly qualified person (preferably an electrician) or someone designated by the importer in
order to avoid possible risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded surface.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic
surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for commercial use and it must
not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3 Chldren's safety
• Packaging materials are dangerous to children. Keep packaging materials in a safe place away
from reach of the children.
• Electrical products are dangerous for the children. Keep children away from the product when it is
in use. Do not let them to tamper with the product. Use child lock to prevent children from inter-
vening with the product.

4/ EN Washing Machine / User’s Manual
• Do not forget to close the loading door when leaving the room where the product is located.
• Store all detergents and additives in a safe place away from the reach of the children by closing
the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass becomes
hot. Therefore, keep especially the children away from the loading door of the
machine while the washing operation is in progress.
1.4 Package nformaton
• Packaging materials of the product are manufactured from recyclable materials in accordance
with our National Environment Regulations. Do not dispose of the packaging materials together
with the domestic or other wastes. Take them to the packaging material collection points desig-
nated by the local authorities.
1.5 Dsposng of the waste product
• This product has been manufactured with high quality parts and materials which can be reu-
sed and are suitable for recycling. Therefore, do not dispose the product with normal domestic
waste at the end of its service life. Take it to a collection point for the recycling of electrical and
electronic equipment. Please consult your local authorities to learn the nearest collection point.
Help protect the environment and natural resources by recycling used products. For children's
safety, cut the power cable and break the locking mechanism of the loading door so that it will be
non-functional before disposing of the product.
1.6 Complance wth WEEE Drectve
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classifi-
cation symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be
reused and are suitable for recycling. Do not dispose of the waste product with normal
domestic and other wastes at the end of its service life. Take it to the collection center for
the recycling of electrical and electronic equipment. Please consult your local authorities
to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not con-
tain harmful and prohibited materials specified in the Directive.
2 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready
for use, review the information in the user manual and make sure that the electricity, tap water supply and
water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a
qualified technician and plumber to have any necessary arrangements carried out.
CPreparation of the location and electrical, tap water and waste water installations at the place of installation is
under customer's responsibility.
Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
BWARNING: Installation and electrical connections of the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out
by unauthorized persons.
AWARNING: Prior to installation, visually check if the product has any defects on it. If so, do not have it
installed. Damaged products cause risks for your safety.
2.1 Appropriate installation location
•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with full load- when they are placed on top of each
other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may fall below 0ºC.
• Place the product at least 1 cm away from the edges of other furniture.
2.2 Removing packaging reinforcement

5/ EN Washing Machine / User’s Manual
2.3 Removing the transportation locks
AWARNING: Do not remove the transportation locks before taking out the packaging reinforcement.
WARNING: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
product will be damaged.
1. Loosen all the bolts with a suitable spanner until they rotate freely (C).
2. Remove transportation safety bolts by turning them gently.
3. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved
again in the future.
Never move the product without the transportation safety bolts properly fixed in place!
2.4 Connecting water supply
CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the
supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with
a blind stopper group.)
AWARNING: Models with a single water inlet should not be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to protection mode and will not operate.
WARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
2. Tighten all hose nuts by hand. Never use a tool when tightening
the nuts.
3. Open the taps completely after making the hose connection
to check for water leaks at the connection points. If any leaks
occur, turn off the tap and remove the nut. Retighten the nut
carefully after checking the seal. To prevent water leakages
and damages caused by them, keep the taps closed when the
machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.
AWARNING: Your house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to
ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so
that it cannot come out.

6/ EN Washing Machine / User’s Manual
•The hose should be attached to a height of at least 40
cm, and 100 cm at most.
• In case the hose is elevated after laying it on the floor
level or close to the ground (less than 40 cm above the
ground), water discharge becomes more difficult and
the laundry may come out excessively wet. Therefore,
follow the heights described in the figure.
• To prevent flowing of dirty water back into the machine
and to allow for easy discharge, do not immerse the
hose end into the dirty water or do not drive it in the
drain more than 15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not
be stepped on and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose
may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose
and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and
leak.
2.6 Adjusting the feet
AWARNING: In order to ensure that the product operates more silently and vibration-free, it must stand level and
balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and
cause crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level
and balanced.
3. Tighten all lock nuts again by hand.
AWARNING: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician
install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-plugs.
BWARNING: Damaged power cables must be replaced by the Authorized Service Agents.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product. See 6.5
4. Install transportation safety bolts in the reverse order of removal procedure; see 3.3.
CNever move the product without the transportation safety bolts properly fixed in place!
AWARNING: Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach
of the children.

7/ EN Washing Machine / User’s Manual
3 Preparation
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage
the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and
brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash“machine washable”or“hand washable”labeled products only with an appropriate programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the
instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce
pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken
off before placing into the machine. Such dusts and powders on the laundry may build up on the inner
parts of the machine in time and can cause damage.
3.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the programme you have selected, but do not
overload; see, "Programme and consumption table".
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing
process.
• Do not use detergent in excess of the amount recommended on the detergent package.
3.4 Initial use
Before starting to use the product, make sure that all preparations are made in
accordance with the instructions in sections“Important safety instructions”and
“Installation”.
To prepare the product for washing laundry, perform first operation in Drum
Cleaning programme. If your product is not equipped with Drum Cleaning
programme, perform the Initial Use procedure in accordance with the methods
described under“5.2 Cleaning the loading door and the drum”section of the user
manual.
CUse an detergents suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is
not harmful for the product.
3.5 Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
The machine automatically adjusts the amount of water according to the weight of the loaded laundry.
Awarning:Follow the information in the“Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.
3.6 Loading the laundry
1. Open the loading door.
2. Place laundry items loosely into the machine.
3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.
CThe loading door is locked while a programme is running. The door can only be opened a while after the
programme comes to an end.

8/ EN Washing Machine / User’s Manual
Awarning: In case of misplacing the laundry, noise and vibration problems may occur in the machine.
3.7 Using detergent and softener
CWhen using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's
instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.
Detergent Drawer
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• Never leave the detergent drawer open while the washing programme is running!
• When using a programme without prewash, do not put any detergent into the prewash compartment
(compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment
nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the
detergent bag or the dispensing ball directly among the laundry in the machine.
• If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash
compartment (compartment nr. "2").
Choosing the detergent type
The type of detergent to be used depends on the type and colour of the fabric.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely
for delicate clothes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for woolens.
A
warning: Use only detergents manufactured specifically for washing machines.
warning: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and
water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid
problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
• Use lesser detergent for small amounts or lightly soiled clothes.
Using softeners
Pour the softener into the softener compartment of
the detergent drawer.
• Do not exceed the (>max<) level marking in the
softener compartment.
• If the softener has lost its fluidity, dilute it with
water before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid detergent cup in compartment nr. “2”.
• If the lqud detergent has lost ts fludty, dlute t wth water before puttng n the detergent cup.
2
231

9/ EN Washing Machine / User’s Manual
Lght colours and whtes Colours Dark colours Delcates/Woollens/
Slks
(Recommended
temperature range based on
soiling level: 40-90 °C)
(Recommended
temperature range based
on soiling level: cold -40 °C)
(Recommended
temperature range
based on soiling
level: cold -40 °C)
(Recommended
temperature range
based on soiling level:
cold -30 °C)
Soiling Level
Heavly Soled
(dffcult
stans such as
grass, coffee,
fruts and
blood.)
It may be necessary to pre-
treat the stains or perform
prewash. Powder and liquid
detergents recommended
for whites can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to clean
clay and soil stains and the
stains that are sensitive to
bleaches.
Powder and liquid
detergents recommended
for colours can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches. Use
detergents without bleach.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended
for heavily soiled
clothes.
Prefer liquid detergents
produced for delicate
clothes. Woollen and
silk clothes must be
washed with special
woollen detergents.
Normally
Soled
(For example,
stans caused
by body on
collars and
cuffs)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
normally soiled clothes.
Powder and liquid
detergents recommended
for colours can be used at
dosages recommended
for normally soiled clothes.
Use detergents without
bleach.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended for
normally soiled
clothes.
Prefer liquid detergents
produced for delicate
clothes. Woollen and
silk clothes must be
washed with special
woollen detergents.
Lghtly Soled
(No vsble
stans exst.)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
lightly soiled clothes.
Powder and liquid
detergents recommended
for colours can be used at
dosages recommended for
lightly soiled clothes. Use
detergents without bleach.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended for
lightly soiled clothes.
Prefer liquid detergents
produced for delicate
clothes. Woollen and
silk clothes must be
washed with special
woollen detergents.
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the Delayed
Start function, do not use liquid detergent.
Using gel and tablet detergent
Apply the following instructions when using tablet, gel and similar detergents.
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the
gel detergent into the main wash detergent compartment during first water intake. If your machine contains a
liquid detergent cup, fill the detergent into this cup before starting the programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum
before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the drum before
washing.
CTablet detergents may leave residues in the detergent compartment. If you encounter such a case, place the tablet
detergent between the laundry, close to the lower part of the drum in future washings.
Use the tablet or gel detergent without selecting the prewash function.
Using starch
• Add liquid starch, powder starch or the fabric dye into the softener compartment.
• Do not use softener and starch together in a washing cycle.
• Wipe the inside of the machine with a damp and clean cloth after using starch.
Using bleaches
• Select a programme with prewash and add the bleaching agent at the beginning of the prewash. Do not put
detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and
add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing
step.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin
irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes.
• When using oxygen based bleaches, select a programme that washes at a lower temperature.
• Oxygen based bleaches can be used together with detergents; however, if its thickness is not the same with
the detergent, put the detergent first into the compartment nr. "2" in the detergent drawer and wait until the
detergent flows while the machine is taking in water. Add the bleaching agent from the same compartment while
the machine is still taking in water.

10 / EN Washing Machine / User’s Manual
When you want to use lqud detergent, pull the
apparatus towards yourself. The part that falls down
wll serve as a barrer for the lqud detergent. If
requred, clean the apparatus wth water when t
s n place or by removng t. If you wll use powder
detergent, the apparatus must be secured at top
poston.
When you want to use lqud detergent, pull the
apparatus towards yourself. The part that falls down
wll serve as a barrer for the lqud detergent. If
requred, clean the apparatus wth water when t
s n place or by removng t. If you wll use powder
detergent, the apparatus must be secured at top
poston.

11 / EN Washing Machine / User’s Manual
5 Operating the product
5.1 Control panel
9
6
3
4.3 Operating the product
4.3.1 Control panel
1 - Programme Selection knob (Uppermost position On / Off)
2 - Spin Speed Indicator LEDs
3 - Child Lock Enabled LED
4 - Door Lock Enabled LED
5 - Delayed Start Indicator LEDs
6 - Programme Follow-up LEDs
7 - Start / Pause Button
8 - Delayed Start Setting Button
9 - Spin Speed Adjustment button
4.3.2 Preparng the machne
1.Make sure that the hoses are connected tightly.
2.Plug in your machine.
3.Turn the tap on completely.
4.Place the laundry in the machine.
5.Add detergent and fabric softener.
4.3.3 Programme selecton and tps for effcent washng
1.Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance
with the "Programme and consumption table" and the temperature table below.
2.Select the desired programme with the Programme Selection knob.

12 / EN Washing Machine / User’s Manual
Programme °C
Maximum load (kg) Programme Duration (min) Water consumption (l) Power consuption (kVt/h) Spin speed
Cottons
90 6 180 83 1.95 1000
60** 6 255 46.4 0.910 1000
60** 3 205 35.4 0.480 1000
40 6 180 81 0.95 1000
20 6 180 81 0.50 1000
Classic 40** 3 205 35 0.475 1000
Cottons 60° With Prewash 60 6 200 92 1.80 1000
Eco 40-60
40*** 6 197 49.0 1.050 1000
40*** 3 155 40.0 0.522 1000
40*** 1. 5 155 36.0 0.400 1000
Synthetics
40 2.5 120 66 0.75 1000
Synthetics
20 2.5 120 66 0.25 1000
Mini
30 628 60 0.15 1000
Wool / Hand Wash 40 1,5 65 45 0.45 1000
Down Wear 40 1,5 105 85 0.8 1000
Shirts 40 2,5 80 42 0.6 800
Drum Clean 90 - 160 67 2.1 600
4.3.4 Programme and consumpton table
4.3.4 Programme and consumpton table
** : Classic and Cottons 60 °C ( ) are the test programs in accordance with EN 60456:2016 and energy label
with Commission Delegated Regulation (EU) 1061/2010
***: Eco 40-60 is the test program in accordance with EN 60456:2016/prA:2019 and energy label with
Commission Delegated Regulation (EU) 2019/2014
- : See the programme description for maximum load.
C
Water and power consumption may vary subject to the changes in water pressure, water hardness
and temperature, ambient temperature, type and amount of laundry, spin speed, and changes in
electric voltage.
Depending on the amount of laundry you have loaded into your machine, there may be a
difference of 1-1.5 hours between the duration shown in the Programme and consumption table
and the actual washing duration. Duration will be automatically updated soon after the washing
starts.
Always select the lowest appropriate temperature. The most efficient programmes in terms of
energy consumption are generally those that perform at lower temperatures and longer duration.
Noise and remaining moisture content are influenced by the spinning speed: the higher the
spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture
content.

13 / EN Washing Machine / User’s Manual
Eco 40-60
40 1000 63:17 1,050 49,0 42 62
40 1000 32:35 0,522 40,0 31 62
40 1000 1,5 2:35 0,400 36,0 27 62
Cottons 20 1000 603:00 0,500 81,0 20 62
Cottons 60 1000 603:20 1,800 92,0 60 62
Synthetcs 40 1000 2,5 02:00 0,750 66,0 40 45
Quck 30 1000 600:28 0,150 60,0 23 62
Temperature
selecton (° C)
Spn speed (rpm)
Capacty(kg)
Duraton of the
program (hh:
mm)
Energy
consumpton
(kWh / cycle)
Water
consumpton
(l / cycle)
Washng
temperature (° C)
Resdual
humdty (%)
Consumpton Values (EN)

14 / EN Washing Machine / User’s Manual
4.3.5 Man programmes
Depending on the type of fabric, use the following main programmes.
• Cottons 20-40-90
Use this programme for your cotton laundry (sheets, bedlinen, towels, bathrobes,
underwear etc.). Your laundry will be washed with vigorous washing action for a longer
washing cycle.
• Synthetics
Use to wash your synthetc clothes (shrts, blouses, synthetc/cotton blends, etc.). Your laundry
wll be washed wth a gentle acton for a shorter washng cycle when compared to the Cottons
programme. For curtans and tulle, t s recommended to use Synthetcs 20˚C or 40˚C programme.
• Woollens / Hand Wash)
Use to wash your woolen/delicate laundry. Your laundry will be washed with a very gentle
washing action in order not to damage the clothes.
4.3.6 Addtonal programmes
For special cases, additional programmes are available in the machine.
C
Additional programmes may differ according to the model of the machine.
• Eco 40-60
The Eco 40-60 programme is able to clean normally soiled cotton laundry declared to be
washable at 40 °C or 60 °C, together in the same cycle, and that this programme is used to
assess the compliance with the EU ecodesign legislation.
Although it washes longer than all other programmes, it provides high energy and water
savings. Actual water temperature may be different from the stated wash temperature. When
you load the machine with less laundry (e.g. ½ capacity or less), periods in programme stages
may automatically get shorter. In this case, energy and water consumption will decrease more.
• Cottons 60 / Classic
Use to wash your normally soiled, durable cotton and linen laundry. Although it washes
longer than all other programmes, it provides high energy and water savings. Actual
water temperature may be different from the stated wash temperature. When you load
the machine with less laundry (e.g. ½ capacity or less), periods in programme stages may
automatically get shorter. In this case, energy and water consumption will decrease more,
providing a more economic wash.
• Cottons 60° with Prewash
Use this programme only for heavily soiled cotton clothes. Add detergent into the prewash
compartment.
• Express
Use this programme to wash your lightly soiled cotton clothes in a short time.
• Shirts
This programme is used to wash the shirts made from cotton, synthetic and synthetic
blended fabrics altogether. It reduces wrinkles. Pre-treatment algorithm is executed.
• Apply the pre-treatment chemical on your garments directly or add it together with
detergent when the machine starts to take water from the main washing compartment.
Thus the machine will wash them in a short period of time and expected lifespan of your
shirts will extend.

15 / EN Washing Machine / User’s Manual
• Duvet / Down Wear
Use this programme to wash your fiber duvets that bear "machine washable" tag. Check
that you have loaded the duvet correctly in order not to damage the machine and the
duvet. Remove the duvet cover before loading the duvet into the machine. Fold the duvet
into two and load it into the machine. Load the duvet into the machine paying attention to
place it in a way that it will not contact the bellow or the glass.
C
Do not load more than 1 double fiber duvet (200 x 200 cm).
Do not wash your duvets, pillows and etc. that contain cotton in the machine.
ACAUTION:
Do not use the washing machine to wash materials such as carpets, rugs etc.
Permanent damage occurs in the machine.
• Down Wear
Use this programme to wash your coats, vest, jackets etc. containing feathers with a
"machine-washable" label on them. Thanks to special spinning profiles, it is ensured that
the water reaches the air gaps amongst the feathers.
• Drum Clean
Use regularly (once in every 1-2 months) to clean the drum and provide the required
hygiene. Operate the programme while the machine is completely empty. To obtain
better results, put powder lime-scale remover for washing machines into the detergent
compartment no. “2”. When the programme is over, leave the loading door ajar so that the
inside of the machine gets dry.
C
This is not a washing programme. It is a maintenance programme.
Do not run the programme when there is something in the machine. If you try to do so, the
machine detects that there is load inside and aborts the programme.
4.3.7 Specal programmes
For specific applications, select any of the following programmes.
•Centrifugado y vaciado (Spin+Drain)
You can use this function to remove the water on the garment of drain the water in the
machine.
Before selecting this programme, select the desired spin speed and press Start / Pause
button. First, the machine will drain the water inside of it. Then, it will spin the laundry with
the set spin speed and drain the water coming out of them.
If you wish to drain only the water without spinning your laundry, select the Pump+Spin
programme and then select the No Spin function with the help of Spin Speed Adjustment
button. Press Start / Pause button.
C
Use a lower spin speed for delicate laundries.
4.3.8 Speed selecton
Whenever a new programme is selected, the recommended spin speed of the selected
programme is displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed
decreases gradually. Then, depending on the model of the product, "Rinse Hold" and "No

16 / EN Washing Machine / User’s Manual
Spin" options appear on the display. When "No Spin" is selected, the rinse level indicator
lights will not turn on.
Rinse hold
If you are not going to unload your clothes immediately after the programme completes,
you can use rinse hold function to keep your laundry in the final rinsing water in order to
prevent them from getting wrinkled when there is no water in the machine. Press Start
/ Pause button after this process if you want to drain the water without spinning your
laundry. Programme will resume and complete after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause
button.
The programme will resume. Water is drained, laundry is spun and the programme is
completed.
C
If the programme has not reached the spinning step, you can change the speed without
switching the machine to Pause mode.
4.3.9 Delayed Start
With the Delayed Start function the startup of the programme may be delayed up to 3, 6 or
9 hours.
C
Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the
clothes.
1. Open the loading door, place the laundry and put detergent, etc.
2. Select a washing programme and spin speed.
3. Set the desired time by pressing the Delayed Start button. When the button is pressed once, 3 hours
delayed start is selected. When the same button is pressed again, 6 hours delay is selected, and when
it is pressed for the third time, 9 hours delayed start is selected. If you press the Delayed Start button
once again, Delayed Start function will be canceled.
4. Press Start / Pause button. Previous delayed start time light turns off and next delayed start time
light turns on after every 3 hours.
5. At the end of the countdown, all delayed start lights will turn off and the selected programme will
start.
C
You can switch the machine to pause mode and add laundry during the delayed start period.
Changing the delayed start period
If you want to change the time during countdown, you will need to cancel the programme
and set the delay time again.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
1. Turn the Programme Selection knob to any programme. Thus, Delayed Start function will be
canceled. The End/Cancel light flashes continuously.
2. Then, select the programme you want to run again.
3. Press Start / Pause button to start the programme.
4.3.10 Startng the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up light showing the startup of the programme will turn on.
4.3.11 Chld Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you
can avoid any changes in a running programme.

17 / EN Washing Machine / User’s Manual
C
If the Programme Selection knob is rotated when the child lock is active, "Child Lock Enabled
LED" will flash 3 times. The Child Lock does not allow any change in the programmes or the
selected speed.
Even if another programme is selected with the Programme Selection knob while the Child
Lock is active, previously selected programme will continue running.
When the Child Lock is active and the machine is running, you can switch the machine
to Pause mode without deactivating the Child Lock by turning the Programme Selection
knob to On / Off position. When you turn the Programme Selection knob afterwards, the
programme will resume.
To activate the Child Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds. While you are holding for
3 seconds, the "Child Lock Enabled LED" will flash. You can release the buttons when the
LEDs become permanently on.
To deactivate the Child Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds while any programme is
running. While you are holding for 3 seconds, the "Child Lock Enabled LED" will flash. You
can release the buttons when the LED turns off completely.
C
In addition to the method above, to deactivate the Child Lock, switch the Programme
Selection knob to On / Off position when no programme is running, and select another
programme.
Child Lock is not deactivated after power failures or when the machine is unplugged.
4.3.12 Progress of programme
Progress of a running programme can be followed from the Programme Follow-up
indicator. At the beginning of every programme step, the relevant indicator light will turn
on and light of the completed step will turn off.
You can change the speed settings without stopping the programme flow while the
programme is running. To do this, the change you are going to make must be in a step after
the running programme step. If the change is not compatible, relevant lights will flash for 3
times.
C
If the machine does not proceed to the spinning step, the Rinse Hold function might be
active or the automatic unbalanced load detection system might be activated due to the
unbalanced distribution of the laundry in the machine.
4.3.13 Loadng door lock
There is a locking system on the loading door of the machine that prevents opening of the
loading door in cases when the water level is unsuitable.
Loading door light will start flashing when the machine is switched to Pause mode. The
machine checks the level of the water inside. If the level is suitable, the Loading Door light
turns off and the loading door can be opened within 1-2 minutes.
If the level is unsuitable, the Loading Door light remains on and the loading door cannot be
opened. If you are obliged to open the Loading Door while the Loading Door light is on, you
must cancel the current programme. See. "Cancelling the programme"
4.3.14 Changng the selectons after programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to pause mode while a programme
is running. The light of the step which the machine is in starts flashing in the Programme
Follow-up indicator to show that the machine has been switched to the pause mode.

18 / EN Washing Machine / User’s Manual
Additionally, when the loading door is openable, the Loading Door light turns off completely.
Changing the speed settings
You can change the speed settings of the programme that is currently running. See "Speed
selection".
C
If no change is allowed, the relevant light will flash 3 times.
Adding or taking out laundry
You can load/unload laundry when a programme is running if the water level is appropriate
to open the door. To do this:
1. Press Start / Pause button to switch the machine to pause mode. The programme follow-up light of
the relevant step during which the machine was switched into the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4. Close the Loading Door.
5. Make changes in speed settings, if necessary.
6. Press Start / Pause button to start the machine.
4.3.15 Cancellng the programme
To cancel the programme, turn the Programme Selection knob to select another
programme. Previous programme will be cancelled. End / Cancel light will flash
continuously to notify that the programme has been canceled.
Your machine will end the programme when you turn the Programme Selection knob;
however, it does not drain the water inside. When you select and start a new programme,
the newly selected programme will start depending on the step the previous programme
was canceled in. For example, it may take in additional water or continue to wash with the
water inside.
C
Some programmes may start by discharging the water inside the machine. Depending on the
step where the programme was canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
4.3.16 End of programme
When the programme ends, "End" LED becomes on at the Programme Follow-up indicator.
1. Wait until the "Door Lock Enabled LED" goes off completely.
2. To switch off the machine, turn the Programme Selection Knob to On/Off position.
3. Take out your laundry and close the loading door. Your machine is ready for the next washing cycle.
4.3.17 Your machne features "Pause Mode".
After you switch on your machine with the programme selection button (by switching the
button to a different position than the On/Off position), if no programme is started or no
other procedure is performed in the selection step or no action is taken within approx. 2
minutes after the selected programme ends, your machine will switch to energy saving
mode automatically. The brightness of the indicator lights will decrease. Also, if your
product has a display that shows programme time, this display will be completely turned
off. If you turn the Programme Selection knob or touch any button, lights and display will
switch back to previous condition. The selections which you make when exiting from the
energy efficiency may change. Please check the correctness of your selections before
starting the programme. If necessary, please make your settings again. This is not an error.

19 / EN Washing Machine / User’s Manual
5 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every 4-5 washing cycles)
as shown below in order to prevent accumulation of powder detergent in
time.
Lft the rear part of the sphon to remove t as llustrated.
C
If more than normal amount of water and softener mixture starts to gather in the softener compartment,
clean the siphon.
2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with
your skin when cleaning.
3 After cleaning, replace the siphon back to its seating and push its front section downwards to make
sure that the locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in your machine in time and may cause
unpleasant odours and washing complaints. To avoid this, use the Drum Cleaning programme. If
your machine is not featured with Drum Cleaning programme, use Cottons-90 programme and
select Additional Water or Extra Rinse auxiliary functions as well. Run the programme without any
laundry in the machine. Before starting the programme, put max. 100 g of powder detergents into the
main wash detergent compartment(compartment nr. 2). If the detergent is in tablet form, put only
one tablet into compartment nr. 2. Dry the inside of the bellow with a clean piece of cloth after the
programme has come to an end.
CRepeat Drum Cleaning process in every 2 months.
Use an detergents suitable for the washing machines.
After every washing check that no foreign substance is left in the drum.
If the holes on the bellow shown in the figure is blocked, open the holes
using a toothpick.
CForeign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using
cleaning agents for stainless steel. Never use steel wool or wire wool.
AWARNING: Never use sponge or scrub materials. These will damage the painted and plastic surfaces.
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary,
and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of
each water intake hose where they are connected to the tap. These filters prevent foreign substances
and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.

20 / EN Washing Machine / User’s Manual
1 Close the taps.
2 Remove the nuts of the water intake hoses to access
the filters on the water intake valves. Clean them with
an appropriate brush. If the filters are too dirty, take
them out by means of pliers and clean them.
3 Take out the filters on the flat ends of the water
intake hoses together with the gaskets and clean
thoroughly under running water.
4 Replace the gaskets and filters carefully in their places
and tighten the hose nuts by hand.
5.5 Draining remaining water and cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging
the pump impeller during discharge of washing water. Thus, the water will be discharged without any
problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is
clogged or in every 3 months. Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of
freezing of the water, water may have to be drained completely.
AWARNING: If the product is not in use, turn the tap off, detach the supply hose and drain the water inside
the machine against any freezing possibility in the region of installation.
WARNING: After each use close the supply hose tap of the product.
In order to clean the dirty filter and discharge the water:
1 Unplug the machine to cut off the supply power.
AWARNING: Temperature of the water inside the machine may rise up to 90 ºC. To avoid burning risk, clean
the filter after the water in the machine cools down.
2 Open the filter cap.
3 Some of our products have emergency draining
hose and some does not have. Follow the steps
below to discharge the water.
Discharging the water when the product has an
emergency draining hose:
a Pull the emergency draining hose out from its
seat
b Place a large container at the end of the hose.
Drain the water into the container by pulling out
the plug at the end of the hose. When the