Beko WRS 5511 BWW User manual

EN |HU |
2820670858
Washing Machine
User’s Manual
WRS 5511 BWW
Mosógép
Használati útmutató

3/ EN Washing Machine / User’s Manual
1 Important nstructons for safety and envronment
This section contains safety instructions that will help protect from risk of personal injury or proper-
ty damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by persons whose physical,
sensory or mental capabilities were not fully developed or who lack experience and knowledge
provided that they are supervised or trained on the safe usage of the product and the risks it
brings out. Children must not play with the product. Cleaning and maintenance works should not
be performed by children unless they are supervised by someone.
• Children of less than 3 years should be kept away unless continuously supervised.
• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machi-
ne will cause electrical parts to overheat. This will cause problems with your product.
• If the product has a failure, it should not be operated unless it is repaired by the Authorized
Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering on after a power interrup-
tion. If you wish to cancel the programme, see "Cancelling the programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the
grounding installation made by a qualified electrician. Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local
regulations.
• The water supply and draining hoses must be securely fastened and remain undamaged.
Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water in the drum. Otherwise,
risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open just a few
minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the
door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by
grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing machines only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and repairing proce-
dures.
• Always have the installation and repairing procedures carried out by the Authorized Service
Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried
out by unauthorized persons.
• If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a
similarly qualified person (preferably an electrician) or someone designated by the importer in
order to avoid possible risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded surface.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic
surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for commercial use and it must
not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3 Chldren's safety
• Packaging materials are dangerous to children. Keep packaging materials in a safe place away
from reach of the children.
• Electrical products are dangerous for the children. Keep children away from the product when it is
in use. Do not let them to tamper with the product. Use child lock to prevent children from inter-
vening with the product.

4/ EN Washing Machine / User’s Manual
• Do not forget to close the loading door when leaving the room where the product is located.
• Store all detergents and additives in a safe place away from the reach of the children by closing
the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass becomes
hot. Therefore, keep especially the children away from the loading door of the
machine while the washing operation is in progress.
1.4 Package nformaton
• Packaging materials of the product are manufactured from recyclable materials in accordance
with our National Environment Regulations. Do not dispose of the packaging materials together
with the domestic or other wastes. Take them to the packaging material collection points desig-
nated by the local authorities.
1.5 Dsposng of the waste product
• This product has been manufactured with high quality parts and materials which can be reu-
sed and are suitable for recycling. Therefore, do not dispose the product with normal domestic
waste at the end of its service life. Take it to a collection point for the recycling of electrical and
electronic equipment. Please consult your local authorities to learn the nearest collection point.
Help protect the environment and natural resources by recycling used products. For children's
safety, cut the power cable and break the locking mechanism of the loading door so that it will be
non-functional before disposing of the product.
1.6 Complance wth WEEE Drectve
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classifi-
cation symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be
reused and are suitable for recycling. Do not dispose of the waste product with normal
domestic and other wastes at the end of its service life. Take it to the collection center for
the recycling of electrical and electronic equipment. Please consult your local authorities
to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not con-
tain harmful and prohibited materials specified in the Directive.
2 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready
for use, review the information in the user manual and make sure that the electricity, tap water supply and
water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a
qualified technician and plumber to have any necessary arrangements carried out.
CPreparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
BWARNING: Installation and electrical connections of the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried
out by unauthorized persons.
AWARNING: Prior to installation, visually check if the product has any defects on it. If so, do not have it
installed. Damaged products cause risks for your safety.
CMake sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with full load- when they are placed on top of each
other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may fall below 0°.

5/ EN Washing Machine / User’s Manual
• Place the product at least 1 cm away from the edges of other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement.
Remove the packaging reinforcement by pulling the ribbon.
2.3 Removing the transportation locks
AWARNING: Do not remove the transportation locks before taking out the packaging reinforcement.
AWARNING: Remove the transportation safety bolts before operating the washing machine! Otherwise,
the product will be damaged.
1. Loosen all the bolts with a suitable spanner until they rotate freely (C).
2. Remove transportation safety bolts by turning them gently.
3. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved
again in the future.
Never move the product without the transportation safety bolts properly fixed in place!
2.4 Connecting water supply
CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary
to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run
smoothly. Attach a pressure reducing valve if water pressure is higher.
CIf you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the
supplied stopper to the hot water valve before operating the product. (Applies for the products supplied
with a blind stopper group.)
AWARNING: Models with a single water inlet should not be connected to the hot water tap. In such a case
the laundry will get damaged or the product will switch to protection mode and will not operate.
AWARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on your
laundry.
1. Tighten all hose nuts by hand. Never use a tool when tightening
the nuts.
2. Open the taps completely after making the hose connection to
check for water leaks at the connection points. If any leaks occur,
turn off the tap and remove the nut. Retighten the nut carefully after
checking the seal. To prevent water leakages and damages caused
by them, keep the taps closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

6/ EN Washing Machine / User’s Manual
AWARNING: Your house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to
ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that
it cannot come out.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the heights
described in the figure.
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose
may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose
and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and
leak.
2.6 Adjusting the feet
A WARNING: In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance the machine by
adjusting the feet.
Otherwise, the product may move from its place and cause crushing and vibration
problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and balanced.
3. Tighten all lock nuts again by hand.
AWARNING: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician
install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-plugs.
BWARNING: Damaged power cables must be replaced by the Authorized Service Agents.

7/ EN Washing Machine / User’s Manual
3 Preparation
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or
pillow case.
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and
brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash“machine washable”or“hand washable”labeled products only with an appropriate programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the
instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce
pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be
shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the
inner parts of the machine in time and can cause damage.
3.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the programme you have selected, but do not
overload; see, "Programme and consumption table".
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing
process.
• Do not use detergent in excess of the amount recommended on the detergent package.
3.4 Initial use
Before starting to use the product, make sure that all preparations are made
in accordance with the instructions in sections“Important safety instructions”
and“Installation”.
To prepare the product for washing laundry, perform first operation in Drum
Cleaning programme. If your product is not equipped with Drum Cleaning
programme, perform the Initial Use procedure in accordance with the
methods described under“5.2 Cleaning the loading door and the drum”
section of the user manual.
CUse an detergents suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is
not harmful for the product.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse order of removal procedure.
CNever move the product without the transportation safety bolts properly fixed in place!
AWARNING: Packaging materials are dangerous to children. Keep packaging materials in a safe place away
from reach of the children.

8/ EN Washing Machine / User’s Manual
3.5 Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
The machine automatically adjusts the amount of water according to the weight of the loaded laundry.
Awarning:Follow the information in the“Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.
3.6 Loading the laundry
1. Open the loading door.
2. Place laundry items loosely into the machine.
3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.
CThe loading door is locked while a programme is running. The door can only be opened a while after the
programme comes to an end.
Awarning: In case of misplacing the laundry, noise and vibration problems may occur in the machine.
3.7 Using detergent and softener
CWhen using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's
instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.
1
3
2
Detergent Drawer
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• Never leave the detergent drawer open while the washing programme is running!
• When using a programme without prewash, do not put any detergent into the prewash compartment
(compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment
nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the
detergent bag or the dispensing ball directly among the laundry in the machine.
• If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash
compartment (compartment nr. "2").
Choosing the detergent type
The type of detergent to be used depends on the type and colour of the fabric.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely
for delicate clothes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for woolens.
A
warning: Use only detergents manufactured specifically for washing machines.
warning: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and
water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid
problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
• Use lesser detergent for small amounts or lightly soiled clothes.

9/ EN Washing Machine / User’s Manual
Using softeners
Pour the softener into the softener compartment of
the detergent drawer.
• Do not exceed the (>max<) level marking in the
softener compartment.
• If the softener has lost its fluidity, dilute it with
water before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid detergent cup in compartment nr.“2”.
• If the lqud detergent has lost ts fludty, dlute t wth water before puttng n the detergent cup.
Lght colours and whtes Colours Dark colours Delcates/Woollens/
Slks
(Recommended
temperature range based
on soiling level: 40-90 °C)
(Recommended
temperature range based
on soiling level: cold
-40 °C)
(Recommended
temperature range
based on soiling
level: cold -40 °C)
(Recommended
temperature range
based on soiling level:
cold -30 °C)
Soiling Level
Heavly
Soled
(dffcult
stans such
as grass,
coffee, fruts
and blood.)
It may be necessary to
pre-treat the stains or
perform prewash. Powder
and liquid detergents
recommended for whites
can be used at dosages
recommended for
heavily soiled clothes. It
is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Use detergents without
bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for heavily soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.
Normally
Soled
(For
example,
stans
caused by
body on
collars and
cuffs)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
normally soiled clothes.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for normally soiled
clothes. Use detergents
without bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended for
normally soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.
Lghtly
Soled
(No vsble
stans exst.)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
lightly soiled clothes.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for lightly soiled clothes.
Use detergents without
bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for lightly soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.

10 / EN Washing Machine / User’s Manual
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use
the Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
Apply the following instructions when using tablet, gel and similar detergents.
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent
cup, put the gel detergent into the main wash detergent compartment during first water intake.
If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the
programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into
the drum before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the
drum before washing.
CTablet detergents may leave residues in the detergent compartment. If you encounter such a case, place
the tablet detergent between the laundry, close to the lower part of the drum in future washings.
Use the tablet or gel detergent without selecting the prewash function.
Using starch
• Add liquid starch, powder starch or the fabric dye into the softener compartment.
• Do not use softener and starch together in a washing cycle.
• Wipe the inside of the machine with a damp and clean cloth after using starch.
Using bleaches
• Select a programme with prewash and add the bleaching agent at the beginning of the prewash.
Do not put detergent in the prewash compartment. As an alternative application, select a
programme with extra rinse and add the bleaching agent while the machine is taking water from
the detergent compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes
skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured
clothes.
• When using oxygen based bleaches, select a programme that washes at a lower temperature.
• Oxygen based bleaches can be used together with detergents; however, if its thickness is not the
same with the detergent, put the detergent first into the compartment nr. "2" in the detergent
drawer and wait until the detergent flows while the machine is taking in water. Add the bleaching
agent from the same compartment while the machine is still taking in water.

11 / EN Washing Machine / User’s Manual
Operatng the product
4.1 Control panel
1 - Programme Selection knob (Uppermost position On / Off)
2 - Spin Speed Indicator LEDs
3 - Child Lock Enabled LED
4 - Door Lock Enabled LED
5 - Delayed Start Indicator LEDs
6 - Programme Follow-up LEDs
7 - Start/Pause Button
8 - Delayed Start Setting Button
9 - Spin Speed Adjustment button
4.2 Preparng the machne
1.Make sure that the hoses are connected tghtly.
2.Plug n your machne.
3.Turn the tap on completely.
4.Place the laundry n the machne.
5.Add detergent and fabrc softener.
4.3 Programme selecton and tps for effcent washng
1.Select the programme sutable for the type, quantty and solng degree of the laundry n accordance
wth the“Programme and consumpton table”and the temperature table below.
2.Select the desred programme wth the Programme Selecton knob.
9
6
3

12 / EN Washing Machine / User’s Manual
Programme °C
Maximum load (kg) Programme Duration (min) Water consumption (l) Power consuption (kVt/h) Spin speed
Cottons 90° 90 5 180 80 1,75 1000
Cottons 40°40 5180 78 0.80 1000
Cottons 20°20 5180 78 0.35 1000
Cottons 60° with Prewash 60 5 200 88 1.40 1000
Cottons Eco 60° 60** 5 255 46 0.87 1000
Cottons Eco 60° 60** 2.5 170 42.5 0.49 1000
Cottons Eco 40° 40** 2.5 170 42.5 0.49 1000
Synthetics 40°40 2,5 120 62 0.65 1000
Synthetics 20°20 2,5 120 62 0.20 1000
Mini 30°30 528 55 0,15 1000
Woollens / Hand Wash 40°40 1,5 65 45 0.40 1000
Down Wear 40° 40 1,5 105 75 0.50 1000
Shirts 40° 40 2,5 80 40 0.55 800
Drum Clean 90 -160 65 2.00 600
4.4 Programme and consumpton table
** : Energy Label programme (EN 60456 Ed.3)
** “Cotton Economic 40°C and Cotton Economic 60°C are standard programmes.” These programmes are
known as ‘40°C cotton standard programme’ and ‘60°C cotton standard programme’ and indicated with the
symbols on the panel.
Water and power consumption may vary subject to the changes in water pressure, water hardness and
temperature, ambient temperature, type and amount of laundry, spin speed, and changes in electric voltage.
Depending on the amount of laundry you have loaded into your machine, there may be a difference of 1-1.5
hours between the duration shown in the Programme and consumption table and the actual washing duration.
Duration will be automatically updated soon after the washing starts.
4.5 Man programmes
Dependng on the type of fabrc, use the followng man programmes.
• Cottons
Use ths programme for your cotton laundry (sheets, bedlnen, towels, bathrobes, underwear etc.). Your
laundry wll be washed wth vgorous washng acton for a longer washng cycle.
• Synthetcs
Use to wash your synthetc clothes (shrts, blouses, synthetc/cotton blends, etc.). Your laundry wll be
washed wth a gentle acton for a shorter washng cycle when compared to the Cottons programme. For
curtans and tulle, t s recommended to use Synthetcs 20˚C or 40˚C programme.
• Wool / Hand Wash
Use to wash your woolen/delcate laundry. Your laundry wll be washed wth a very gentle washng acton
n order not to damage the clothes.
“The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of
machine washable wool products provided that the products are washed according to the instructions on
the garment label and those issued by the manufacturer of this washing machine. M0000.”
“In UK, Eire, Hong Kong and India the Woolmark trade mark is a Certification trade mark.”

13 / EN Washing Machine / User’s Manual
4.6 Addtonal programmes
For specal cases, addtonal programmes are avalable n the machne.
Addtonal programmes may dffer accordng to the model of the machne.
• Cotton Economy
Use ths programme to wash your laundry washable n cottons programme for a longer tme, stll wth a
very good performance for savng purposes.
Cotton Eco programme consumes less energy compared to other cotton programmes.
• Cottons wth Prewash
Use ths programme only for heavly soled cotton clothes. Add detergent nto the prewash compartment.
• Mn 30
Use ths programme to wash your lghtly soled cotton clothes n a short tme.
• Shrts
Ths programme s used to wash the shrts made from cotton, synthetc and synthetc blended fabrcs
altogether. It reduces wrnkles. Pre-treatment algorthm s executed.
• Apply the pre-treatment chemcal on your garments drectly or add t together wth detergent when the
machne starts to take water from the man washng compartment. Thus the machne wll wash them n a
short perod of tme and expected lfespan of your shrts wll extend.
• Down Wear
Use ths programme to wash your coats, vest, jackets etc. contanng feathers wth a “machne-washable”
label on them. Thanks to specal spnnng profles, t s ensured that the water reaches the ar gaps
amongst the feathers.
• Drum Cleanng
Use regularly (once n every 1-2 months) to clean the drum and provde the requred hygene. Operate
the programme whle the machne s completely empty. To obtan better results, put powder lme-scale
remover for washng machnes nto the detergent compartment no. “2”. When the programme s over,
leave the loadng door ajar so that the nsde of the machne gets dry.
Ths s not a washng programme. It s a mantenance programme.
Do not run the programme when there s somethng n the machne. If you try to do so, the
machne detects that there s load nsde and aborts the programme.
4.7 Specal programmes
For specfc applcatons, select any of the followng programmes.
• Rnse
Use when you want to rnse or starch separately.
• Spn+Pump
You can use ths functon to remove the water on the garment of dran the water n the machne.
Before selectng ths programme, select the desred spn speed and press Start / Pause button. Frst, the
machne wll dran the water nsde of t. Then, t wll spn the laundry wth the set spn speed and dran the
water comng out of them. If you wsh to dran only the water wthout spnnng your laundry, select the
Pump+Spn programme and then select the No Spn functon wth the help of Spn Speed Adjustment
button. Press Start / Pause button.
Use a lower spn speed for delcate laundres.
4.8 Speed selecton
Whenever a new programme s selected, the recommended spn speed of the selected programme s
dsplayed on the spn speed ndcator.
To decrease the spn speed, press the Spn Speed Adjustment button. Spn speed decreases gradually.
Then, dependng on the model of the product,“Rnse Hold”and“No Spn”optons appear on the dsplay.
When“No Spn”s selected, the rnse level ndcator lghts wll not turn on.
Rnse hold
If you are not gong to unload your clothes mmedately after the programme completes, you can
use rnse hold functon to keep your laundry n the fnal rnsng water n order to prevent them from
gettng wrnkled when there s no water n the machne. Press Start / Pause button after ths process

14 / EN Washing Machine / User’s Manual
f you want to dran the water wthout spnnng your laundry. Programme wll resume and complete
after dranng the water. If you want to spn the laundry held n water, adjust the Spn Speed and press
Start / Pause button.
The programme wll resume. Water s draned, laundry s spun and the programme s completed.
If the programme has not reached the spnnng step, you can change the speed wthout
swtchng the machne to Pause mode.
4.9 Delayed Start
Wth the Delayed Start functon the startup of the programme may be delayed up to 3, 6 or 9 hours.
Do not use lqud detergents when you set Delayed Start! There s the rsk of stanng of the
clothes.
1. Open the loadng door, place the laundry and put detergent, etc.
2. Select a washng programme and spn speed.
3. Set the desred tme by pressng the Delayed Start button. When the button s pressed once, 3 hours
delayed start s selected. When the same button s pressed agan, 6 hours delay s selected, and when
t s pressed for the thrd tme, 9 hours delayed start s selected. If you press the Delayed Start button
once agan, Delayed Start functon wll be canceled.
4. Press Start / Pause button. Prevous delayed start tme lght turns off and next delayed start tme
lght turns on after every 3 hours.
5. At the end of the countdown, all delayed start lghts wll turn off and the selected programme wll
start.
You can swtch the machne to pause mode and add laundry durng the delayed start perod.
Changng the delayed start perod
If you want to change the tme durng countdown, you wll need to cancel the programme and set the
delay tme agan.
Cancelng the Delayed Start functon
If you want to cancel the delayed start countdown and start the programme mmedately:
1. Turn the Programme Selecton knob to any programme. Thus, Delayed Start functon wll be canceled.
The End/Cancel lght flashes contnuously.
2. Then, select the programme you want to run agan.
3. Press Start / Pause button to start the programme.
4.10 Startng the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up lght showng the startup of the programme wll turn on.
4.11 Chld Lock
Use Chld Lock functon to prevent chldren from tamperng wth the machne. Thus you can avod any
changes n a runnng programme.
If the Programme Selecton knob s rotated when the chld lock s actve,“Chld Lock Enabled
LED”wll flash 3 tmes. The Chld Lock does not allow any change n the programmes or the
selected speed.
Even f another programme s selected wth the Programme Selecton knob whle the Chld
Lock s actve, prevously selected programme wll contnue runnng.
When the Chld Lock s actve and the machne s runnng, you can swtch the machne
to Pause mode wthout deactvatng the Chld Lock by turnng the Programme Selecton
knob to On / Off poston. When you turn the Programme Selecton knob afterwards, the
programme wll resume.
To actvate the Chld Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds. Whle you are holdng for 3 seconds, the
“Chld Lock Enabled LED” wll flash. You can release the buttons when the LEDs become permanently on.

15 / EN Washing Machine / User’s Manual
To deactvate the Chld Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds whle any programme s runnng. Whle
you are holdng for 3 seconds, the“Chld Lock Enabled LED” wll flash. You can release the buttons
when the LED turns off completely.
In addton to the method above, to deactvate the Chld Lock, swtch the Programme
Selecton knob to On / Off poston when no programme s runnng, and select another
programme.
Chld Lock s not deactvated after power falures or when the machne s unplugged.
4.12 Progress of programme
Progress of a runnng programme can be followed from the Programme Follow-up ndcator. At
the begnnng of every programme step, the relevant ndcator lght wll turn on and lght of the
completed step wll turn off. You can change the speed settngs wthout stoppng the programme flow
whle the programme s runnng. To do ths, the change you are gong to make must be n a step after
the runnng programme step. If the change s not compatble, relevant lghts wll flash for 3 tmes.
If the machne does not proceed to the spnnng step, the Rnse Hold functon mght be
actve or the automatc unbalanced load detecton system mght be actvated due to the
unbalanced dstrbuton of the laundry n the machne.
4.13 Loadng door lock
There s a lockng system on the loadng door of the machne that prevents openng of the loadng
door n cases when the water level s unsutable. Loadng door lght wll start flashng when the
machne s swtched to Pause mode. The machne checks the level of the water nsde. If the level s
sutable, the Loadng Door lght turns off and the loadng door can be opened wthn 1-2 mnutes. If
the level s unsutable, the Loadng Door lght remans on and the loadng door cannot be opened.
If you are oblged to open the Loadng Door whle the Loadng Door lght s on, you must cancel the
current programme. See.“Cancellng the programme”
4.14 Changng the selectons after programme has started
Swtchng the machne to pause mode
Press the Start / Pause button to swtch the machne to pause mode whle a programme s runnng.
The lght of the step whch the machne s n starts flashng n the Programme Follow-up ndcator to
show that the machne has been swtched to the pause mode. Addtonally, when the loadng door s
openable, the Loadng Door lght turns off completely.
Changng the speed settngs
You can change the speed settngs of the programme that s currently runnng. See“Speed selecton”.
If no change s allowed, the relevant lght wll flash 3 tmes.
Addng or takng out laundry
1. Press Start / Pause button to swtch the machne to pause mode. The programme follow-up lght of
the relevant step durng whch the machne was swtched nto the pause mode wll flash.
2. Wat untl the Loadng Door can be opened.
3. Open the Loadng Door and add or take out the laundry.
4. Close the Loadng Door.
5. Make changes n speed settngs, f necessary.
6. Press Start / Pause button to start the machne.
4.15 Cancellng the programme
To cancel the programme, turn the Programme Selecton knob to select another programme. Prevous
programme wll be cancelled. End / Cancel lght wll flash contnuously to notfy that the programme
has been canceled. Your machne wll end the programme when you turn the Programme Selecton
knob; however, t does not dran the water nsde. When you select and start a new programme, the
newly selected programme wll start dependng on the step the prevous programme was canceled n.
For example, t may take n addtonal water or contnue to wash wth the water nsde.
Some programmes may start by dschargng the water nsde the machne. Dependng
on the step where the programme was canceled n, you may have to put detergent and
softener agan for the programme you have selected anew.

16 / EN Washing Machine / User’s Manual
4.16 End of programme
When the programme ends,“End” LED becomes on at the Programme Follow-up ndcator.
1. Wat untl the“Door Lock Enabled LED”goes off completely.
2. To swtch off the machne, turn the Programme Selecton Knob to On/Off poston.
3. Take out your laundry and close the loadng door. Your machne s ready for the next washng cycle.
4.17 Your machne features“Pause Mode”.
After you switch on your machine with the programme selection button (by switching the button
to a different position than the On/Off position), if no programme is started or no other procedure
is performed in the selection step or no action is taken within approx. 2 minutes after the selected
programme ends, your machine will switch to energy saving mode automatically. The brightness
of the indicator lights will decrease. Also, if your product has a display that shows programme time,
this display will be completely turned off. If you turn the Programme Selection knob or touch any
button, lights and display will switch back to previous condition. The selections which you make
when exiting from the energy efficiency may change. Please check the correctness of your selections
before starting the programme. If necessary, please make your settings again. This is not an error.
5 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every 4-5 washing cycles)
as shown below in order to prevent accumulation of powder detergent in
time.
Lft the rear part of the sphon to remove t as llustrated.
C
If more than normal amount of water and softener mixture starts to gather in the softener compartment,
clean the siphon.
2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with
your skin when cleaning.
3 After cleaning, replace the siphon back to its seating and push its front section downwards to make
sure that the locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in your machine in time and may cause
unpleasant odours and washing complaints. To avoid this, use the Drum Cleaning programme. If your
machine is not featured with Drum Cleaning programme, use Cottons-90 programme and select
Additional Water or Extra Rinse auxiliary functions as well. Run the programme without any laundry in
the machine. Before starting the programme, put max. 100 g of powder detergents into the main wash
detergent compartment(compartment nr. 2). If the detergent is in tablet form, put only one tablet into
compartment nr. 2. Dry the inside of the bellow with a clean piece of cloth after the programme has
come to an end.
CRepeat Drum Cleaning process in every 2 months.
Use an detergents suitable for the washing machines.
After every washing check that no foreign substance is left in the drum.
If the holes on the bellow shown in the figure is blocked, open the holes
using a toothpick.

17 / EN Washing Machine / User’s Manual
CForeign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using
cleaning agents for stainless steel. Never use steel wool or wire wool.
AWARNING: Never use sponge or scrub materials. These will damage the painted and plastic surfaces.
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and
dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of
each water intake hose where they are connected to the tap. These filters prevent foreign substances
and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.
1 Close the taps.
2 Remove the nuts of the water intake hoses to access
the filters on the water intake valves. Clean them with
an appropriate brush. If the filters are too dirty, take
them out by means of pliers and clean them.
3 Take out the filters on the flat ends of the water
intake hoses together with the gaskets and clean
thoroughly under running water.
4 Replace the gaskets and filters carefully in their places
and tighten the hose nuts by hand.
5.5 Draining remaining water and cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging
the pump impeller during discharge of washing water. Thus, the water will be discharged without any
problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is
clogged or in every 3 months. Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of
freezing of the water, water may have to be drained completely.
AWARNING: If the product is not in use, turn the tap off, detach the supply hose and drain the water inside
the machine against any freezing possibility in the region of installation.
WARNING: After each use close the supply hose tap of the product.

18 / EN Washing Machine / User’s Manual
In order to clean the dirty filter and discharge the water:
1 Unplug the machine to cut off the supply power.
AWARNING: Temperature of the water inside the machine may rise up to 90 ºC. To avoid burning risk, clean
the filter after the water in the machine cools down.
2 Open the filter cap.
3 Some of our products have emergency draining
hose and some does not have. Follow the steps
below to discharge the water.
Discharging the water when the product has an
emergency draining hose:
a Pull the emergency draining hose out from its
seat
b Place a large container at the end of the hose.
Drain the water into the container by pulling out
the plug at the end of the hose. When the
container is full, block the inlet of the hose by replacing the plug. After the container is emptied, repeat
the above procedure to drain the water in the machine completely.
c When dranng of water s fnshed, close the end by the plug agan and fx the hose n ts place.
d Turn the pump filter to take it out.
Discharging the water when the product does not
have an emergency draining hose:
a Place a large container in front of the filter to
catch water from the filter.
b Loosen pump filter (anticlockwise) until water
starts to flow. Fill the flowing water into the
container you have placed in front of the filter.
Always keep a piece of cloth handy to absorb any
spilled water.
c When the water inside the machine is finished,
take out the filter completely by turning it.
4 Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.
5 Install the filter.
6 If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat
the tabs in the lower part into their places first, and then press the upper part to close.

19 / EN Washing Machine / User’s Manual
6 Technical specifications
Complyng Commsson Delegated Regulaton (EU) No 1061/2010
Suppler name or trademark Beko
Model name WRS 5511 BWW
Rated capacty (kg) 5
Energy effcency class / Scale from A+++ (Hghest Effcency) to D (Lowest Effcency) A++
Annual Energy Consumpton (kWh) (1) 148
Energy consumpton of the standard 60°C cotton programme at full load (kWh) 0.870
Energy consumpton of the standard 60°C cotton programme at partal load (kWh) 0.490
Energy consumpton of the standard 40°C cotton programme at partal load (kWh) 0.490
Power consumpton n‘off-mode’(W) 0.25
Power consumpton n‘left-on mode’(W) 1.00
Annual Water Consumpton (l) (2) 9679
Spn-dryng effcency class / Scale from A (Hghest Effcency) to G (Lowest Effcency) C
Maxmum spn speed (rpm) 1000
Remanng mosture Content (%) 62
Standard cotton programme(3) Cotton Eco 60°C and 40°C
Programme tme of the standard 60°C cotton programme at full load (mn) 255
Programme tme of the standard 60°C cotton programme at partal load (mn) 170
Programme tme of the standard 40°C cotton programme at partal load (mn)170
Duraton of the left-on mode (mn) N/A
Arborne acoustcal nose emssons washng/spnnng (dB) 60/78
Bult-n Non
Heght (cm) 84
Wdth (cm) 60
Depth (cm) 36.5
Net weght (±4 kg.) 51
Sngle Water nlet / Double Water nlet • / -
• Avalable
Electrcal nput (V/Hz) 230 V / 50Hz
Total current (A) 10
Total power (W) 1550
(1) Energy Consumpton based on 220 standard washng cycles for cotton programmes at 60°C and 40°C at full and partal load, and
the consumpton of the low-power modes. Actual energy consumpton wll depend on how the applance s used.
(2) Water consumpton based on 220 standard washng cycles for cotton programmes at 60°C and 40°C at full and partal load. Actual
water consumpton wll depend on how the applance s used.
(3) "Standard 60°C cotton programme" and the "standard 40°C cotton programme" are the standard washng programmes to whch
the nformaton n the label and the fche relates and these programmes are sutable to clean normally soled cotton laundry and
that they are the most effcent programmes n terms of combned energy and water consumpton.
Techncal specfcatons may be changed wthout pror notce to mprove the qualty of the product.

20 / EN Washing Machine / User’s Manual
7 Troubleshooting
Programme cannot be started or selected.
• Washng machne has swtched to self protecton mode due to a supply problem (lne voltage, water
pressure, etc.). >>> To cancel the programme, turn the Programme Selecton knob to select another
programme. Prevous programme wll be cancelled. (See“Cancelng the programme”)
Water in the machine.
• Some water mght have remaned n the product due to the qualty control processes n the
producton. >>> Ths s not a falure; water s not harmful to the machne.
Machine vibrates or makes noise.
• Machne mght be standng unbalanced. >>> Adjust the feet to level the machne.
• A hard substance mght have entered nto the pump flter. >>> Clean the pump flter.
• Transportaton safety bolts are not removed. >>> Remove the transportaton safety bolts.
• Laundry quantty n the machne mght be too lttle. >>> Add more laundry to the machne.
• Machne mght be overloaded wth laundry. >>>Take out some of the laundry from the machne or
dstrbute the load by hand to balance t homogenously n the machne.
• Machne mght be leanng on a rgd tem. >>> Make sure that the machne s not leanng on
anythng.
Machine stopped shortly after the programme started.
• Machne mght have stopped temporarly due to low voltage. >>> It wll resume runnng when the
voltage restores to the normal level.
Programme time does not countdown. (On models with display)
• Tmer may stop durng water ntake. >>> Tmer ndcator wll not countdown untl the machne takes
n adequate amount of water. The machne wll wat untl there s suffcent amount of water to avod
poor washng results due to lack of water. Tmer ndcator wll resume countdown after ths.
• Tmer may stop durng heatng step. >>> Tmer ndcator wll not countdown untl the machne
reaches the selected temperature.
• Tmer may stop durng spnnng step. >>> Automatc unbalanced load detecton system mght be
actvated due to the unbalanced dstrbuton of the laundry n the drum.
• Machne does not swtch to spnnng step when the laundry s not evenly dstrbuted n the drum
to prevent any damage to the machne and to ts surroundng envronment. Laundry should be
rearranged and re-spun.
Foam is overflowing from the detergent drawer.
• Too much detergent s used. >>> Mx 1 tablespoonful softener and ½ l water and pour nto the man
wash compartment of the detergent drawer.
• Put detergent nto the machne sutable for the programmes and maxmum loads ndcated n the
“Programme and consumpton table”. When you use addtonal chemcals (stan removers, bleachs and
etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
• Excessve foam mght have occurred and automatc foam absorpton system mght have been
actvated due to too much detergent usage. >>> Use recommended amount of detergent.
• Machne does not swtch to spnnng step when the laundry s not evenly dstrbuted n the drum
to prevent any damage to the machne and to ts surroundng envronment. Laundry should be
rearranged and re-spun.
Awarning:If you cannot eliminate the problem although you follow the instructions in this section,
consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.