Belair 3000 User manual

Belair 3000
Operating instructions (E)
Congratulations on your purchase!
Belair is a product that provides for effective removal of odours in
toilet rooms. It upholds the highest standards of comfort,
functionality, quality, design and energy efficiency.
Belair is a toilet seat with an integrated filter that quickly and
efficiently eliminates unpleasant gases before they become dispersed
into the surrounding environment.
Adjustable screws allow for simple assembly and disassembly of the
device on most toilet bowls.
The device requires less than a tenth of the energy of conventional
bathroom ventilation systems and saves on the loss of heating energy
during cold periods of the year.
Please carefully read through the operating instructions in their
entirety before putting the device into operation.
Note!
- Prior to operation, please check to make sure your voltage system
corresponds to the voltage indicated for the device (220-230 volts).
- Never clean the device when the filter housing is open.
- Make sure that no water or other fluid enters the air intake slots. Any
fluid inside the device could cause permanent damage.
- Children or individuals with limited physical, sensory or mental
capacities should only employ this product after a thorough
explanation of how to use devices connected to electric power.

1. Assembly
a. Install the Belair 3000 like a conventional toilet seat: If necessary,
first remove the old seat by loosening the screws on the sides of the
toilet bowl (down below).
b. Place the Belair 3000 on the toilet bowl and insert the eccentric
screws (8) provided with the assembly kit through the eyes on the seat
holder (7) and then through the holes in the toilet bowl.
c. Before tightening the Belair screws with the provided nuts, make
sure the sensor on the underside (4) is in contact with the rim of the
toilet bowl when the seat (1) is lowered. If not, reposition the device
until this is the case. Now tighten the nuts very firmly.
d. Connect the device to the power supply by inserting the power
adapter into a power socket. If no power socket is available in the toilet
room, you can run the cable under the door to the outside and connect
it to a standard extension cord if required.
If necessary, use self-adhesive cable holders to guide the cable along
the wall.
Note: Do not leave any sections of the cable lying unsecured on the
floor, as this would constitute a risk of falling and damage the device

if accidentally pulled.
2. Utilisation
The sensor mounted on the underside activates the ventilation function
when the user sits down on the seat. The gases are thus directly
captured and eliminated.
Avoid unnecessarily dropping the seat down onto the toilet bowl.
Repeated dropping of the seat could damage the device.
3. Cleaning
Belair is cleaned like a normal toilet seat with commercially available
toilet cleaners and a non-abrasive cloth.
Note: Do not clean with a toilet brush or a soaking wet sponge as this
could cause water to enter the air intake slots (6). In this case, the
warranty becomes null and void.
4. Changing the filter
With the decrease of the filter’s effectiveness over time – after a
period of one year at the latest – the filter (3) should be removed by
simultaneously pressing on the snap-fit closures and lifting the cover
of the filter housing (5) and subsequently replaced with a new filter.
Filters can be purchased at any store where the devices are sold.
Another option is to order a subscription for the filters. Simply use the
enclosed order card or sign up at ...
www.belair-swiss.ch
... for the filter subscription system.
Dispose of the old filter along with regular household waste.
5. Troubleshooting
a. Problem: The device does not switch on.
> Is the adapter of the device correctly plugged in? If not, plug in the
adapter in the correct manner. You might also need to check the fuses
or circuit breakers for that particular outlet.
> Does the protruding sensor on the underside of the seat come into
contact with the toilet bowl when the seat is lowered? If not, loosen
the screws and reposition the device until sensor touches the toilet
bowl. Tighten the screws again.

b. Problem: The device does not eliminate odours.
> Is a filter inserted? Check whether a filter is contained in the filter
housing (at the back). If yes, the filter might be used up (after approx.
one year). If the filter has gotten wet, it could be that it is no longer
effective. Insert a new filter.
See www.belair-swiss.ch.
c. Problem: The lid (2) has become detached from the seat.
> The lid can be detached from the seat for cleaning. To reattach it,
simply place it back onto the two nubs on the sides of the seat.
6. Warranty
As the manufacturer, we offer a warranty for this device valid for one
year from the date of purchase. Within this warranty period, we will
remedy all defects due to material or manufacturing defects at no
charge, either through repair or exchange as we see fit. The warranty
can be claimed in all countries where Belair is sold by authorised
retailers.
Excluded from warranty coverage are: damage from improper use,
normal wear and tear as well as defects that only insignificantly
affect the value or usability of the device.
If the product is worked on by agents other than authorised Belair
customer service partners or if replacement parts are used that were
not provided by Belair, the warranty becomes null and void.
For warranty claims, please properly clean and disinfect the device and
send it along with the proof of purchase to an authorised Belair
customer service partner. Uncleaned devices will not be accepted.
Technical specifications:
- Voltage/Power:
220-230 volts / 2.8 watts
BELAIR SOLUTIONS AG
Wiesenstrasse 11
CH – 8008 Zurich
Tel. [phone]
[email protected]
www.belair-swiss.ch
www.belair-swiss.ch