Halsey Taylor 4470NLHB Series User manual

97886C (Rev. D - 09/15)
Hose Bib Fountain Accessories
PAGE 1
Owners Manual
HOSE BIB FOUNTAIN ACCESSORIES
For Use On 4400 Series Fountains With Floor Mount Base
Installer
To assure you install this accessory easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES.
Hose Bib Accessory
Models 4470NLHB* & LK4470NLHB*
Locking Hose Bib Accessory
Models 4471LHB* & LK4471LHB*
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

PAGE 2 97886C (Rev. D - 12/15)
Hose Bib Fountain Accessories
DESCRIPTION
75624C
75619C
45836C*
70977C
70972C
75623C
66555C
66475C
66641C
75535C
45837C*
45838C*
75521C
1
2
3
4
5
6
7
8
9
10
11
12
NS
PART NO.
Fitting - Hose Vacuum Breaker
Faucet - 1/2" NPT
Panel - Access W/Bib Recess
Nut - Lock 1/2" Conduit
Elbow - 90° x 1/2" MPT
Fitting - Tee 1/2" X 1/2" X 3/8"
Tube - 1/2" O.D. X 35.00" Lg.
Tube - 3/8" O.D.Tee to Strainer
Tube - 1/2" O.D. X 4.38" Lg.
Screw - 1/4-20 X 3/4" Torx
Panel - Locking Hose Bib
Door - Locking Hose Bib
Bit - Pinned Torx T-27
ITEM
NO.
PARTS LIST
FOUNTAIN BODY (EXISTING)
1
2
3
FINISHED
GRADE
INSTALLATION INSTRUCTIONS
1. Shut off water supply to fountain.
2. Determine location for installation of Hose Bib Accessory.
Remove existing access cover plate. This accessory is
designed to replace the existing access cover.
3. Disconnect the fountain water line from the main water
supply. Connect Tube (Item 8) to existing fountain
strainer as shown below.
4. Connect Tee (Item 6) to Tube (Item 8). Connect main water
supply to Tee using 1/2" Copper Tube (Item 9). DO NOT
TURN MAIN WATER SUPPLY ON AT THIS TIME !
5. Connect Hose Bib Accessory water line to the Tee and to
the Elbow (Item 5) on the Access Panel (Item 3) using
1/2" Copper Tube (Item 7) as shown below, maintain
loop in coil to facilitate installation and removal of Access
Panel.
6. Turn on main water supply. Check for leaks. If there are
leaks, turn off main water supply and correct the water
leaks as required. After insuring that all connections are
leak free, leave main water supply on and replace any
panels that may have been removed in the installation
process.
7. Assemble Hose Bib Accessory to the main fountain body.
4
5
6
7
8
9
WATER INLET
STRAINER
TO FOUNTAIN
REGULATOR
(EXISTING)
11 10
12
LOCKING HOSE BIB
FOUNTAIN BODY
(EXISTING)
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sufx example:
4470NLHBEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
*select color option to complete part number
NS = Not Shown