Belanger SpinLite User manual

SpinLite® Low Side Washer
Belanger, Inc. * P.O. Box 5470 * Northville, MI 48167-5470
Customer Service Phone [phone] * Fax [phone]
SpinLite® Low Side Washer
1MANUAL962 Rev 01

Belanger Equipment Owner’s Manual
SpinLite® Low Side Washer
Copyright 2022
Belanger, Inc®
This manual and the accompanying equipment are protected by United States trademark, copyright, and patent laws. You
may make one copy of this manual. Do not make additional copies of this manual or electronically transmit it in any form
whatsoever, in whole or in part, without the prior written permission of Belanger, Inc.®
The registered trademarks used in this document are the property of their respective owners. The use of such trademarks is
for reference purposes only and does not imply sponsorship or approval of Belanger, Inc. ® by these companies or any
companies affiliated with their respective owners.

CURRENT REVISION LOG
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Rev
Release
Date
Page
Description
01
03/21/22
Front Cover
Updated front cover to new design
Manual
Updated Belanger logo throughout the entire manual
3
Changed Belanger Limited Warranty on Parts from 30 days to 90 days
10
Top image: Removed 51”
Bottom image: Changed the 51” dimension to 13” Conveyor: 51” & 14-1/2” Conveyor: 52-1/2” (per
Project #32-523)
15
Added page Installation: Identify Conveyor (per Project #32-523)
16
Added Note about the 13” Conveyor being shown in images in manual
Updated dimension to driver side Low Side Washer 13” Conveyor: 51” and 14-1/2” Conveyor: 52-1/2”
Added to note under image: (13” Conveyor: 51” / 14-1/2” Conveyor: 52-1/2”) (per Project #32-523)
17
Removed placement dimensions DS: 47-1/2”, PS 103-1/2”, and spacing dimension 78-1/2” for the
staggered QuickFire® Plus assemblies
Updated dimension to driver side Low Side Washer 13” Conveyor: 51” and 14-1/2” Conveyor: 52-1/2”
Added to note under image: (13” Conveyor: 51” / 14-1/2” Conveyor: 52-1/2”) (per Project #32-523)
18
For Stand-Alone Installation: added dimension for 13” Conveyor: 51” / 14-1/2” Conveyor: 52-1/2”
Added dimension information to Step 2 for the 13” & 14-1/2” wide conveyors (per Project #32-523)
20
Removed placement dimensions DS: 47-1/2”, PS 103-1/2”, and spacing dimension 78-1/2” for the
staggered QuickFire® Plus assemblies
For Staggered with QuickFire® Plus Installation: added dimension for 13” Conveyor: 51” / 14-1/2”
Conveyor: 52-1/2” for placement of driver side SpinLite® Low Side Washer
Added dimension information to Step 2 for the 13” & 14-1/2” wide conveyors ( per Project #32-523)
42 & 43
Changed Motor/Gearbox from 1GEABX-AS660 to 112271 and 1GEABX-AS661 to 112272 (per
Project #10038)
Back Cover
Updated back cover to new design

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Table of Contents
Belanger Incorporated Limited Warranty..............................................................3
Operational Warning...............................................................................................4
Important Safety Information –MUST READ........................................................5
Safety Symbols and Signal Words .................................................................................................................................. 5
Safety Warnings .............................................................................................................................................................. 6
Introduction .............................................................................................................7
Before You Get Started ................................................................................................................................................... 8
Specifications..........................................................................................................9
Requirements .................................................................................................................................................................. 9
Physical .......................................................................................................................................................................................... 9
Utility............................................................................................................................................................................................... 9
Electrical......................................................................................................................................................................................... 9
General Dimensions...................................................................................................................................................... 10
Inspection ..............................................................................................................11
Equipment to Inspect Before Installation....................................................................................................................... 11
Motor Cables ................................................................................................................................................................................ 11
Hub LED Electrical Connections .................................................................................................................................................. 12
Installation .............................................................................................................15
Identify Conveyor .......................................................................................................................................................... 15
Tunnel Placement: Overview ........................................................................................................................................ 16
Standard, Stand-Alone Configuration .......................................................................................................................................... 16
Staggered, with QuickFire® Plus assemblies .............................................................................................................................. 17
Tunnel Placement: Preparation..................................................................................................................................... 18
Tunnel Placement: Stand-Alone Installation ................................................................................................................. 18
Tunnel Placement: Staggered Installation with QuickFire® Plus .................................................................................. 20
Loading ShineMitt™ Material on Hubs.......................................................................................................................... 22
Utilities........................................................................................................................................................................... 26
Water Connections: Water Line to the SpinLite® Low Side Washers ......................................................................................... 26
Pneumatic Connections: Air Panel to Cylinders........................................................................................................................... 28
Electrical Connections: Air Panel to Controller ............................................................................................................................ 30
Pneumatic Connections: Initial Air Settings for Air Panel ............................................................................................................ 31
Electrical Connections: Motor....................................................................................................................................................... 32
Maintenance ..........................................................................................................36
Daily .............................................................................................................................................................................. 36
Monthly.......................................................................................................................................................................... 36
Quarterly........................................................................................................................................................................ 36
Troubleshooting............................................................................................................................................................. 37

SPINLITE® LOW SIDE WASHER
2Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Table of Contents
Maintenance (continued)....................................................................................368
Exploded Parts View......................................................................................................................................................38
Leg Assembly Components: Driver & Passenger Side................................................................................................................ 38
Manifold Assembly....................................................................................................................................................................... 39
Arm Assembly: Overview............................................................................................................................................................. 40
Driver Side Arm Assembly: Cylinder Assembly ........................................................................................................................... 40
Driver Side Arm Assembly: Pivot Shaft, Bearing Assemblies & Electrical Cables ...................................................................... 41
Driver & Passenger Side Arm Assembly: Shaft Assembly .......................................................................................................... 41
Passenger Side Arm Assembly: Cylinder Assembly & Electrical Cables .................................................................................... 42
Passenger Side Arm Assembly: Pivot Shaft & Bearing Assemblies............................................................................................ 42
Motor Gearbox & Torque Plate Assembly ................................................................................................................................... 43
Slip Ring Assembly: 110708 (2)................................................................................................................................................... 43
Motor/Gearbox, Drive Shaft & Cover Assembly........................................................................................................................... 44
Hub Assembly: Overview............................................................................................................................................................. 45
Hub Assembly: 110703 (2)........................................................................................................................................................... 46
Hub ShineMitt™ Fill Pattern......................................................................................................................................................... 47
Hub ShineMitt™........................................................................................................................................................................... 47
ShineMitt™ Short Lead: 111060 (Qty. 80)................................................................................................................................... 48
Hub Cover Assembly: 110763 (2)................................................................................................................................................ 49
LED RGB Assembly: 110764 (2) ................................................................................................................................................. 49
Filler Strips for Driver Side ........................................................................................................................................................... 50
Filler Strips for Passenger Side ................................................................................................................................................... 51
Air Panel: 102060......................................................................................................................................................................... 52

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Belanger Incorporated Limited Warranty
LIMITED WARRANTY:
Equipment:
Subject to the limitations stated below, Seller warrants that the Equipment sold hereunder, which is fabricated by Seller,
shall be free from defects in workmanship and material under normal use and service for a period of 1 year plus 30 days
from the date of invoice - CATPumps will be warranted for 2 years from the date of invoice.
Parts:
Subject to the limitations stated below, Seller warrants that the Parts sold hereunder, shall be free from defects in
workmanship and material under normal use and service for a period of 90 days from the date of invoice.
Limitations on All Warranties:
The warranties contained in this Section 13 are subject to the following limitations: (1) they are void if the factory
specifications for operation and maintenance, found in original equipment manuals, and component manuals, are not
followed, or if other than factory authorized erection, alterations or modifications are made to any Parts or Equipment; (2)
defective Parts are warranted to the Purchaser only for repair or replacement through an authorized Purchaser or
Distributor of Seller, or direct with Seller for a period of 13 months from the date of invoice; however, this warranty excludes
all claims for failure resulting from normal wear and tear, improper installation, omission of factory specified preventative
maintenance, misuse, abuse, negligence, third party damages, or acts of God and Purchaser agrees to submit to and
assist Seller or its authorized Purchaser or Distributor in conducting in-warranty inspections of the Goods including
inspection of any Equipment or Parts claimed to be defective by the Purchaser; (3) the cost of providing labor or repair to
replace Equipment and Parts warranted to Purchaser will be included within the warranty only if such claim is made within
120 days from the date of invoice and then only during normal business hours through an authorized Purchaser or
Distributor of Seller, or direct with Seller, and labor and service provided beyond the labor warranty period shall be subject
to labor charges at the rates established by the local authorized Purchaser or Distributor or direct with Seller; (4) the
warranties shall be void for all Equipment failures and premature Part wear caused by the use of corrosive chemicals in the
wash process, and the following list includes some, but not all, of the particularly corrosive chemicals that if used in
conjunction with Equipment or Parts will void the warranty: Hydrofluoric Acid, Ammonium Bi-fluoride, Bromic Acid, Muriatic
Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric Acid, Sodium Hydroxide and Chlorinated Solvents;
(5) Seller makes no warranty, express or implied, with respect to the design or operation of any entire system, in which
Seller’s Equipment or Parts sold hereunder are mere components;(6) in no event shall Seller be liable for any incidental,
special, consequential, punitive or exemplary damages resulting from the furnishing, performance or use of any Goods or
services sold pursuant hereto, whether due to a breach of contract, breach of warranty, negligence or any other claim at
law or equity. Seller shall not be liable for any damages of any kind, including, but not limited to, loss of business;
inconvenience, or property damage of any kind; nor for any damages of whatever nature resulting in any way from the
Purchaser’s selection and use of any chemicals not manufactured exclusively by Seller but used with the purchased
Equipment or Parts; or for any service not expressly provided herein related to or arising from the Equipment or Parts sold.
Seller shall not be liable for damages resulting from Purchaser’s use of any engineering recommendations, sales
representations, technical assistance, advice, or data other than that information contained in Belanger manuals; (7) all
warranties, express, implied, or statutory, pertaining to the Equipment and Parts apply to the Purchaser only; are not
transferable; are fully set forth herein; and no addition to or modification thereto shall be binding upon the Seller, unless
made in writing and signed by a duly authorized employee of Seller.
No Other Warranties:
THIS LIMITED WARRANTY FOR EQUIPMENT AND PARTS IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, WHETHER STATUTORY OR OTHERWISE, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE CONTAINED IN THE UNIFORM COMMERCIAL CODE –SALES ARE EXPRESSLY DISCLAIMED.
Copyright ©2020 by Belanger, Inc. All rights reserved. No part of this work may be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval
system, except as may be expressly permitted by the 1976 Copyright Act. Belanger reserves the right to change or modify
the Belanger Inc. Limited warranty without notice.

SPINLITE® LOW SIDE WASHER
4Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Operational Warning
Formulations containing the chemicals listed below are particularly dangerous and should not be
used even at low concentrations:
•Hydrofluoric Acid
•Ammonium Bi-fluoride
•Bromic Acid
•Muriatic Acid
•Sulfonic Acid
•Phosphoric Acid
•Hydrogen Cyanide
•Hydrochloric Acid
•Chlorinated Solvents
Belanger, Inc.®, does not endorse or condone the use of chemicals that are potentially dangerous to human health, the
environment, or property. Belanger® recognizes that it is the right and sole decision of the end-user operators of our
equipment as to the type and dilution ratio of the chemicals used in their facilities. We strongly recommend that the end-
user does not select products containing any of the chemicals listed above as an ingredient in the wash solutions. The
chemicals listed above are potentially dangerous to human health and have a detrimental, deteriorating effect on the
equipment and the facility. Be advised that a portion of, or all of your warranty will be voided if you determine to use any
of the chemicals listed above as an ingredient in the wash solutions in conjunction with your Belanger® automatic car
wash equipment:
Limitation (4), of Paragraph (8), Limited Warranty, of the Belanger® Terms and Conditions of Sales describes the
potential limitation of warranty due to your chemical selection:
(4) This warranty shall be void for all equipment failures and premature component wear caused by the use of
corrosive chemicals in the wash process. The following list includes some, but not all, of the particularly corrosive
chemicals that if used in conjunction with Belanger® equipment will void the warranty: Hydrofluoric Acid, Ammonium
Bi-fluoride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric Acid, and
Chlorinated Solvents. The Purchaser also agrees to accept the responsibility and liability for the selection and use of
any chemicals listed above;
However, should the end-user decide to use formulations containing any of the above ingredients, the end-user should
institute a comprehensive training program and implement detailed operational parameters within their organization for
the proper handling and treatment of such products to minimize the potential dangers involved. Consult your chemical
supplier for assistance in establishing operational guidelines in the use of their products. MSDS (Material Safety Data
Sheet) should be obtained from the chemical supplier before using any chemical formulation.
CAUTION
The installer is responsible for re-tightening ALL lugs, set screws, and terminals
located in the electrical panels during the installation process. Components may
vibrate loose during shipping.

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Important Safety Information – MUST READ
This section introduces the hazard and safety precautions associated with installing, maintaining, or
servicing this product. Before performing any task on this product, read this safety information and the
applicable sections in this manual, where additional hazards and safety precautions for your task may be
found. Electrical shock could occur and cause death or serious injury if these safe service procedures
are not followed.
Safety Symbols and Signal Words
Alert Symbol
This safety alert symbol is used in this manual and on warning labels to alert
you to precautions, which must be followed to prevent potential personal
safety hazards. Obey safety directives that follow this symbol to avoid
possible injury or death.
Signal Words
The signal words used in this manual and on warning labels tell you the seriousness of particular
safety hazards. The precautions that follow must be followed to prevent death, injury, or damage to
the equipment.
DANGER
This signal word is used to alert you to a hazard or unsafe practice which WILL RESULT IN
DEATH OR SERIOUS INJURY
This alerts you to a hazard or unsafe practice which COULD RESULT IN DEATH OR SERIOUS
INJURY
CAUTION
This signal word designates a hazard or unsafe practice which MAY RESULT IN MINOR INJURY
CAUTION
When used by itself, CAUTION designates a hazard or unsafe practice which MAY RESULT IN
PROPERTY OR EQUIPMENT DAMAGE
Before You Begin
Only trained or authorized individuals knowledgeable in the related procedures should install,
inspect, maintain or service this equipment.
Read the Manual
Read, understand and follow this manual and any other labels or related materials supplied with this
equipment. If you do not understand the procedure, call a Belanger, Inc. representative at 248-349-
7010. It is imperative to your safety and the safety of others to understand the procedures before
beginning work.

SPINLITE® LOW SIDE WASHER
6Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Important Safety Information – MUST READ
Safety Warnings
DANGER
DISCONNECT MAIN POWER SUPPLY PRIOR TO
SERVICING OR MAINTAINING EQUIPMENT
Belanger recommends that all workers observe the OSHA (U.S. Department of
Labor Occupational Safety & Health Administration) Lockout / Tagout procedure
prior to performing service or maintenance on machinery and equipment. Doing so
will prevent unexpected energization, startup, or release of hazardous energy while
maintenance and servicing activities are being performed.
BE SURE TO OBSERVE THE OPERATING ENVELOPE.
EQUIPMENT MAY START UNEXPECTICALLY. OVERHEAD,
ROTATING, AND/OR MOVING COMPONENTS COULD RESULT
IN SERIOUS INJURY OR DEATH.
BE AWARE OF FOREIGN OBJECTS IN THE AREA
SURROUNDING A ROTATING PIECE OF EQUIPMENT.
OBJECTS MAY BECOME TANGLED WITH EQUIPMENT AND
COULD RESULT IN SERIOUS INJURY OR DEATH.
CAUTION
BE AWARE OF HAZARDS ASSOCIATED WITH
EQUIPMENT INSTALLED ON THE FLOOR
THAT MAY BE A TRIP HAZARD.
It is imperative to your safety and the safety of others to always follow safe work
procedures.

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Introduction
Thank you for your purchase of the Belanger, Inc. SpinLite® Low Side Washers. This manual will
familiarize you with the SpinLite® Low Side Washer installation, operation, and maintenance.
Both passenger and driver side Low Side Washers are easily mounted to the tunnel floor requiring only
the installation of the ShineMitt™ cleaning material and the connection of the utilities.
Before attempting to install the equipment, please read the entire instruction manual and refer to it
throughout the installation process. Keep this manual as a guide to proper maintenance.
IT IS IMPERATIVE THAT WHEELS ARE SPINNING DURING
ANY PERIOD THAT THE CONVEYOR IS ACTIVATED
SpinLite® Low Side Washer
Driver Side Assembly
SpinLite® Low Side Washer
Passenger Side Assembly
Motor/Gearbox
& Cover
Hub Assembly
with LED Lights
Electrical
Junction Box
ShineMitt™
Cleaning Material
Water
Manifold
Pivot Stop
Leg
Assembly
Arm Asy. with Drive
Shaft & Bearings
Hub Cover

SPINLITE® LOW SIDE WASHER
8Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Introduction
Before You Get Started
Below is a list of the SpinLite® Low Side Washer equipment you will receive in your shipment and the
tools that are needed to install the equipment.
Tools needed for installation:
Forklift (optional)
Level
Hammer drill with 5/8” bit
50-foot extension cord
Tape measure (25 feet or greater)
Safety glasses
Miscellaneous hand tools
Work gloves
Equipment included: Qty
SpinLite® Low Side Washer Driver Side Assembly
1
SpinLite® Low Side Washer Passenger Side Assembly
1
SpinLite® Low Side Washer Drive Shaft & Hub Assembly, installed
2
ShineMitt™ Cleaning Material: 111060
80
Motovario Motor/Gearbox & Cover, installed
2
Accessory Box: 111744
1
Accessory Box (111744) includes: Qty
Air Panel: 102060
1
Kwik Bolts 3 Zinc 5/8” x 6”: 1FSTNR-ST750
8
Clamp Single Ear for 1/2” Hose: 1CLAMP467
4
Note: Uncrate and inspect the shipment for damage, and verify that all pieces are there. If there is
any damaged equipment, file a claim with the trucking company immediately. Receiving party
is responsible for filing a claim with the trucking company. Notify your local distributor or
Belanger, Inc.® immediately if the shipment is determined damaged or incomplete.

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Specifications
Requirements
Physical
Tunnel space: required driver side
68”
Tunnel space: required passenger side
68”
Utility
Electrical
Two 1 HP, 3-Phase Motors, terminated in Junction Box at the top of each Leg Assembly. See
the chart below for requirements.
Two 24V Signal Wires from the configured LED SpinLite Lighting Panel, terminated at the
Junction Box at the top of each Leg Assembly
One 110V Control Wire terminated at Supplied Pneumatic Control Panel
Water
One 1/2” poly-flow tube for Chemical/Water, Tee’d to feed driver and passenger side SpinLite®
Low Side Washer assemblies, terminated at Water Manifold on each Leg Assembly
Water Output: 6 GPM total (Two Nozzles per side: 1.5 GPM x 65°@ 40 psi per Nozzle)
Pneumatic
One 1/4” poly-flow tube Main Pneumatic feed to Air Panel (1CFM)
Four 1/4” Airlines for Extend and Retract of the Arm Cylinders on each SpinLite® Low Side
Washer Assembly
Electrical
Voltage
Hz
FLA
Per Motor
208
60
4.6
230
60
4.2
460
60
2.1
575
60
1.7
DISCONNECT AND LOCKOUT ELECTRICAL POWER BEFORE SERVICING ANY
EQUIPMENT!
CAUTION
Always wear safety glasses when performing maintenance on any equipment.
CAUTION
It is recommended that a licensed electrician is contracted to perform all electrical installations.
CAUTION
A compressed Air System should be set correctly to support 90 PSI necessary to operate equipment,
but should never be set to deliver more than 120 PSI air pressure to the Belanger specified
equipment.

SPINLITE® LOW SIDE WASHER
10 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Specifications
General Dimensions
Top View
68”
Equipment Envelope
157”
Entrance View
106”
13” Conveyor: 51”
14-1/2” Conveyor: 52-1/2”

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Inspection
Equipment to Inspect Before Installation
Uncrate the driver and passenger side SpinLite® Low Side Washer assemblies and inspect for damage.
Before removing the SpinLite® Low Side Washer assemblies from the shipping pallets, several electrical
and component connections on the units should be inspected. Inspect the following:
Motor Cables
The Spin Lite® LSW assemblies each have a 1HP 3-Phase motor that comes wired for the voltage
selected when ordered which was either 208/230, 460, or 575 VAC.
1) Refer to the yellow sticker on the SpinLite® LSW Assemblies Electrical Junction Box to
verify that the motors are wired correctly for the site voltage.
2) The Electrical Cables for the Motor and LED lights are already routed from the
Motor/Gearbox Cover assembly, through the Arm, into the Leg, and then into the Electrical
Junction Box attached to the Leg Assembly. Refer to the image below.
3) The Motor and LED cables are ready to be connected to their Main Power source after
installation.
Note: If there is any damaged equipment, file a claim with the trucking company immediately.
Receiving party is responsible for filing claim with trucking company. Notify your local
distributor or Belanger, Inc. immediately if shipment is determined damaged or incomplete.
Motor Cable
Electrical
Junction Box
LED Cable
CAUTION:
FACTORY WIRED
208/230 VAC
CAUTION:
FACTORY WIRED
575 VAC
CAUTION:
FACTORY WIRED
460 VAC
Leg Assembly
Motor/Gearbox &
Cover Assembly
Arm Assembly
Note:
Parts of the Arm and Leg assembly were
made transparent in image to clearly see
the routing of the Motor and LED cables.
3/4” Liquid Tite Conduit
encloses both Cables
3/8” LiquidTite Conduit,
in two (2) places,
encloses each Cable

SPINLITE® LOW SIDE WASHER
12 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Inspection
Equipment to Inspect Before Installation
Hub LED Electrical Connections
Each SpinLite® LSW assembly has an electrical Slip Ring and Wire Harness to power the LEDs on
the Hub. All electrical connections: power cable to Slip Ring, Slip Ring to Wire Harness, and Wire
Harness to LEDs need to be inspected. Each of these wire connections must be secure, protected
from water intrusion, and have adequate clearance from the spinning Hub Skins during operation.
1) Remove the Motor/Gearbox Top Cover to gain access to the LED Main Power Cable to Slip
Ring electrical connection.
2) Locate the Slip Ring electrical connection and disconnect the wires, apply dielectric grease
to the receptor side of the connector to help protect the connection from water intrusion.
3) Align the Slip Ring connectors properly and reconnect the wires, as shown in the image
above on the right. Wrap the connection with electrical tape to protect it even more from the
car wash elements.
4) Reattach the Top Cover to the Motor/Gearbox Bottom Cover.
Slip Ring
LED Power
Cable
Note: When making the wire connections be sure to use the indicators to align them correctly;
they should go together easily. DO NOT force a connection it may bend the pins in the
connector which may result in some or all of the LEDs not working.
Align the indicators and
press the connectors
together gently.
Step 3:
Locate and
disconnect
the Main LED
Power Cable
from the Slip
Ring Wire.
Step 2a:
Apply dielectric grease
to the Slip Ring Wire
Receptor.
Step 2b:
Slip Ring Wire
Motor/ Gearbox
Top Cover

SPINLITE® LOW SIDE WASHER
1MANUL962 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Inspection
Equipment to Inspect Before Installation
Hub LED Electrical Connections
5) Remove the Hub Covers on both of the SpinLite® LSW assemblies, see image below left.
6) Remove one of the Hub Skins on each of the SpinLite® LSW Hub Assembly to gain access
to the Wire Harness and LED wires, see image above right.
7) Locate the Wire Harness to Slip Ring connection and the four (4) LED connections.
Disconnect each of the wire connections and apply dielectric grease to the receptor side of
the connector to help prevent water intrusion.
8) Align the connectors properly and reconnect the wires. Wrap the connections with electrical
tape to protect them from the car wash elements.
Hub Covers
Hub Skins
Wire Harness
LEDs
Note: When making the wire connections be sure to use the indicators to align them correctly;
they should go together easily. DO NOT force a connection it may bend the pins in the
connector which may result in some or all of the LEDs not working.
Slip Ring to Wire Harness Connection
Step 7 & 8:
For each of the electrical connections do the following:
1.)
Disconnect each and apply dielectric grease to
receptor side
2.) Properly align and reconnect connectors
3.) Wrap connections with electrical tape
Wire Harness to LED Connections
It may be necessary to
remove some of the zip ties
to perform Step 7.
Note:

SPINLITE® LOW SIDE WASHER
14 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL962
Inspection
Equipment to Inspect Before Installation
Hub LED Electrical Connections
9) Verify that the Wire Harness wires are secured to the Drive Shaft with tie straps and the LED
Connections are above the Hub Spider with proper clearance from the spinning Hub Skins.
10) Reinstall the Hub Skins and Hub Covers onto the Hubs assemblies.
Secure the Wire Harness to
the Drive Shaft with zip ties
and make sure the LED
Connections are above the
Hub Spider.
Step 9: