Bell'O PVS4252 User manual
ASSEMB Y INSTRUCTIONS
PVS4252
AUDIO/VIDEO TE EVISION SYSTEM
Bell’O International Corp. will not be responsible for failure to assemble as directed or for the improper assembly, use or handling of this stand.
FOR YO R SAFETY, PLEASE FOLLOW THESE PRECA TIONS:
!
DO NOT P ACE ITEMS ON THE SHE VES WHICH EXCEED THE MAXIMUM WEIGHT IMITS OF 125 BS. FOR TOP SHE F,
50 BS. FOR THE MIDD E SHE F, AND 75 BS. FOR THE BOTTOM SHE F.
A WAYS P ACE THE HEAVIEST
COMPONENTS ON THE BOTTOM SHE F.
! A WAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMB ED UNIT.
! BE CAREFU WHEN MOVING THE ASSEMB ED FURNITURE AFTER THE G ASS SHE VES HAVE BEEN IN-
STA ED, AND/OR WHEN THERE IS EQUIPMENT OCATED ON THE FURNITURE AS THIS MAY CAUSE
THE SHE VES AND OTHER ITEMS TO BECOME UNSECURED AND FA .
! WHEN IN USE, THIS FURNITURE MUST BE P ACED ON A F AT, SO ID AND EVE SURFACE.
! DO NOT EAN ON THE TV WHEN IT IS ON THE TV STAND.
! DO NOT C IMB OR STEP ON THE STAND.
! DO NOT BANG INTO OR P ACE YOUR OWN WEIGHT ON THE G ASS SHE F.
PARTS IST
#
M2
M3
M4
M5
M6
M7
1
1
2
1
1
1
1
Quantity
Part
M1
#
M9
M10
M11
M12
M13
M14
1
16
6
12
1
1
1
Quantity
Part
M8
40 mm
35 mm
12 mm
1. ATTACH the eft Side E-Frame (M1) to the CMS®(Cable Management System) Rear Panel (M2) using four 40 mm Bolts (M11) and
one 12 mm Screw (M12) as shown above. TIGHTEN all Screws and Bolts fully.
2. ATTACH the Right Side E-Frame (M3) to the CMS®(Cable Management System) Rear Panel (M2) using four 40 mm Bolts (M11)
and one 12 mm Screw (M12) as shown above. TIGHTEN all Screws and Bolts fully.
M11
ASSEMB Y INSTRUCTIONS
NOTE: 2 PEOP E ARE RECOMMENDED TO ASSEMB E THIS FURNITURE. TO AVOID DAMAGE DURING ASSEMB Y,
IT SHOU D BE ASSEMB ED ON A SOFT SURFACE.
Fig. 1
M11
M1
M2
M3 M12
(View fromRear)
3. ATTACH the eft Side Support (M4) to the eft Side E-Frame (M1) using two 40 mm Bolts (M11) as shown above.
TIGHTEN all Bolts fully.
4. ATTACH the Right Side Support (M5) to the Right Side E-Frame (M3) using two 40 mm Bolts (M11) as shown above.
TIGHTEN all Bolts fully.
Fig. 2
M4
M1
M3
M5
M11
(View fromFront)
5. ATTACH the Bottom Front Shelf Support (M7) to the eft and Right Side Supports (M4, M5) and to the eft and Right Side
E-Frames (M1, M3). SECURE the Bottom Front Shelf Support using six 12 mm Screws (M12) as shown above. TIGHTEN all
Screws fully.
6. ATTACH the Top and Middle Front Shelf Supports (M6) to the eft and Right Side E-Frames (M1, M3) as shown.
SECURE EACH Front Shelf Support using two 12 mm Screws (M12) as shown above. TIGHTEN all Screws fully.
Fig. 3
M6
M6
M5
M12
M12
M12
M7
M3
M1
M12
M4
M12
7. On a soft, flat surface and with the help of an assistant, CAREFU YTI T the preassembled TVstand onto its back.
8. With the help of an assistant, CAREFU YP ACE the Bottom Glass Shelf (M10) into place. MAKESURE the silver discs under the Glass Shelf are
properly inserted into the holes in the bottom extensions of the eft and Right Side E-Frames (M1, M3) as shown. SECURE the Bottom Glass Shelf
using two 35 mm Screws (M13). Tighten, but be careful not to overtighten!
9. With the help of an assistant, CAREFU YP ACE the Middle Glass Shelf (M9) into place. MAKESURE the silver discs under the Glass Shelf are
properly inserted into the holes in the middle extensions of the eft and Right Side E-Frames (M1, M3) as shown. SECURE the Middle Glass Shelf
using two 35 mm Screws (M13). Tighten, but be careful not to overtighten!
10. With the help of an assistant, CAREFU YP ACE the Top Glass Shelf (M8) into place. MAKESURE the silver discs under the Glass Shelf are
properly inserted into the holes in the top extensions of the eft and Right Side E-Frames (M1, M3) as shown. SECURE the Top Glass Shelf using
two 35 mm Screws (M13). Tighten, but be careful not to overtighten!
11. With the help of an assistant, CAREFU Y IFT the TV stand up into an upright position.
NOTE (!): There are Adjustable Foot Levelers under the Left and Right Side Supports (M4, M5). T RN these Adjustable Levelers to make sure
the TV stand is LEVEL AND EVENLY S PPORTED on a flat, solid floor. There are three Adjustable Glass Pads along the top edge of EACH
Front Shelf Support (M6, M7). T RN the Adjustable Glass Pads to make sure ALL Glass Shelves are LEVEL AND EVENLY
S PPORTED before placing any items on them.
Fig. 4
M8
M9
M10
M13
M6
M6
M4
M7
M13
M13
!
Table of contents
