Belling BRHCF9BLS User manual

Cooker Hood
Instruction Manual
BRHCF9BLS
BRHCF9BLB
BRHCF6BLB

Content
Safety instructions
1
Installation
3
Start using your cooker hood
8
Troubleshooting
9
Maintenance and cleaning
10
Environment protection
14

1
SAFETY INSTRUCTIONS
This manual explains the proper installation and use of your cooker hood, please read it
carefully before using even if you are familiar with the product. The manual should be kept in
a safe place for future reference.
These instructions shall also be available in an alternative format, e.g. on a website or on
request from the user in a format such as a DVD.
Never to do:
●Do not try to use the cooker hood
without the grease filters or if the filters
are excessively greasy!
●Do not install above a cooker with a high
level grill.
●Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
●Never leave naked flames under the
cooker hood.
●If the cooker hood is damaged, do not
attempt to use.
●Do not flambé under the cooker hood.
●CAUTION: Accessible parts may become
hot when used with cooking appliances.
●The minimum distance between the
supporting surface for the cooking vessels
on the hob and the lowest part of the
cooker hood. (When the cooker hood is
located above a gas appliance, this
distance shall be at least 65 cm)
●The air must not be discharged into a flue
that is used for exhausting fumes from
appliances burning gas or other fuels.
Always to do:
●Important! Always switch off the
electricity supply at the mains during
installation and maintenance such as light
bulb replacement.
●The cooker hood must be installed in
accordance with the installation
instructions and all measurements
followed.
●All installation work must be carried out by
a competent person or qualified
electrician.
●Please dispose of the packing material
carefully. Children are vulnerable to it.
●Pay attention to the sharp edges inside
the cooker hood especially during
installation and cleaning.
●When the cooker hood is located above a
gas appliance,the minimum distance
between the supporting surface for the
cooking vessels on the hob and the
lowest part of the cooker hood that
distance must be:
Gas cookers: 75 cm
Electric cookers: 65 cm
Coal or oil cookers: 75 cm
●Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker hood.
●Warning: Failure to install the screws or
fixing device in accordance with these
instructions may result in electrical
hazards

2
●Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
Always to do:
●Always put lids on pots and pans when
cooking on a gas cooker.
●When in extraction mode, air in the room
is being removed by the cooker hood.
Please make sure that proper ventilation
measures are being observed. The cooker
hood removes odours from room but not
steam.
●Cooker hood is for domestic use only.
●If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
●This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
●Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
Always to do:
●Caution: The appliance and its accessible
parts can become hot during operation.
Be careful to avoid touching the heating
elements. Children younger than 8 years
old should stay away unless they are
under permanent supervision.
●There shall be adequate ventilation of the
room when the cooker hood is used at
the same time as appliances burning gas
or other fuels.
●There is a fire risk if cleaning is not carried
out in accordance with the instructions
●Regulations concerning the discharge of air
have to be fulfilled.
●Clean your appliance periodically by
following the method given in the chapter
MAINTENANCE.
●For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this
instruction manual.
●Regarding the details about the method
and frequency of cleaning, please refer to
maintenance and cleaning section in the
instruction manual.
●Cleaning and user maintenance shall not
be made by children without supervision.
●When the cooker hood and appliances
supplied with energy other than
electricity are simultaneously in operation,
the negative pressure in the room must
not exceed 4 Pa (4 x 10-5 bar).
●WARNING: Danger of fire: do not store
items on the cooking surfaces.
●Asteam cleaner is not to be used.
●NEVER try to extinguish a fire with water,
but switch off the appliance and then
cover flame e.g. with a lid or a fire blanket.

3
INSTALLATION (VENT OUTSIDE)
MOUNTING OF THE V-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the half-parts to
its body.The images only show an example of how to mount the V-flap,the outlet may be
various according to different models and configuration.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6
• a pin 3 should be top oriented;
• the axis 4 should be inserted in the holes 5 on body;
• repeat all the operations for the 2nd half-part
INSTALLATION
If you have an outlet to the outside, your cooker hood can be connected as below picture by
means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material with
an interior diameter of 150mm)

4
1. Before installation, turn the unit off and unplug it from the outlet.
2. The cooker hood should be placed at a distance of 65~75cm above the cooking surface for
best effect.
3. Install the hook on a suitable place once the installation height is fixed, and keep it in line.
The fixed position of the inside chimney bracket is the place of chimney. See pic 2.
4. Fasten the outlet with 4 pcs ST4*8mm, fix the expansion pipe and tie it with cable tie. See
Pic 3.

5
5. Fix the outside chimney bracket on the outside chimney, and be sure that the inside
chimney can be adjusted freely. Afterwards, install the chimney on the cooker hood.See Pic4.
6. Put the cooker hood on the hook. See Pic 5.
5. Adjust the height of the inside chimney to the position of the inside chimney bracket and fix
it with screws, after adjusting the position, fix the body with safety screw. See Pic 6.

6
Note: The two safety vents are positioned on the back housing, with diameter of 6mm.
HINTS FOR EXHAUST DUCT INSTALLATION
The following rules must be strictly followed to obtain optimal air extraction:
• Keep expansion pipe short and straight.
• Do not reduce the size or restrict expansion pipe.
• When using expansion pipe always install the pipe pulled taut to minimize pressure loss.
• Failure to observe these basic instructions will reduce the performance and increase noise
levels of the cooker hood.
• Any installation work must be carried out by a qualified electrician or competent person.
•Do not connect the ducting system of the hood to any existing ventilation system which is
being used for any other appliance ,such as warmer tube, gas tube , hot wind tube.
•The angle of the bend of the expansion pipe should not be less than 120º; you must direct
the pipe horizontally, or, alternatively, the pipe should go up from the initial point and should
be led to an outer wall.
•After the installation ,make sure that the cooker hood is level to avoid grease collection at
one end.
•Ensure the expansion pipe selected for installation complies with relevant standards and is
fire retardant.

7
WARNING:
For safety reason, please use only the same size of fixing or
mounting screw which are recommended in this instruction
manual.
Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.

8
Start Using Your Cooker Hood
Touch control with LED display
1. Press the “Power” button, the button control the “on” & “off ” of the hood.
2. Keep pressing the button “Speed”, the motor runs as low / mid / high / low / mid…, and
the LED display will indicate as 1-2-3-1-2…
3. Press “Light” button, the light is on, press this button again, the light is off.
4. When the hood is working, press the “Timer” button, the hood will go into the status of
acquiescent working (acquiescent time is 9mins), and then, the LED display will indicate as
“9-8-7…-1-0”, when indicate “0”, the hood wil turn off automatically. If you keep pressing
“Timer” button, the hood will go on or off.