Belson Outdoors RPPB6F User manual
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
( 1 ) - CENTER BENCH END ( 2 ) - BENCH ENDS
( 4 ) - FOUR FRAME RINGS
( 2 ) - BOTTOM PLATE
( 8 ) - EIGHT SIDE PANELS
B - BULL NOSED BENCH BOARD
( 2 ) - TWO BULL NOSED BENCH BOARDS
A - CENTER BENCH BOARD
( 4 ) - FOUR CENTER BENCH BOARDS
www.belson.com
1 - #3 PHILLIPS DRIVE BIT
2 - 9/16" SOCKET WRENCH
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
32 - #12 X 2-1/2" PAN HEAD PHILLIPS SCREW
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.
4 - 3/8" X 4-1/4" HEX BOLT HEAD BOLT
8 - 3/8" FLAT WASHER
4 - 3/8" NYLON LOCK NUT
www.belson.com
STEP #1:
AS SHOWN IN THE DIAGRAM BELOW, PLACE ONE SIDE PANEL FACE DOWN ON A FLAT SURFACE.
PLACE THE FRAME RINGS AT THE TOP AND BOTTOM SECTIONS OF THE PANEL, BEING SURE TO
LINE UP THE PRE-DRILLED HOLES IN THE FRAME RINGS TO THE PRE-DRILLED PILOT HOLES IN
THE SIDE PANEL. USE THE DIAGRAM BELOW FOR PLACEMENT. FASTEN USING ( 1 ) ONE 2-1/2”
PAN HEAD SCREW PER HOLE.
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #2:
PLACE ANOTHER SIDE PANEL BESIDE THE PREVIOUS PANEL, SO THAT IT TOUCHES AS DISPLAYED IN
THE DIAGRAM ABOVE. GENTLY TURN THE SIDE PANEL WITH THE RINGS INSTALLED ON TO THE NEW
SIDE PANEL, MAKING SURE THE HOLES LINE UP WITH THE PRE-DRILLED PILOT HOLES IN THE NEW
PANEL. FASTEN USING ( 1 ) ONE 2-1/2” PAN HEAD SCREW PER HOLE.
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #3:
REPEAT THE PREVIOUS STEP.
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #4:
PLACE THE BOTTOM PANEL INTO THE OPENING BETWEEN THE FRAME RINGS.
www.belson.com
STEP #5:
REPEAT STEP 2.
TURN THE PLANTER UPRIGHT ONTO ITS BASE. PLEASE USE CAUTION WHILE MOVING AS THE
PLANTER WILL WEIGHT APPROXIMATELY 96 POUNDS.
REPEAT STEPS #1-5 TO COMPLETE THE SECOND PLANTERS BOX.
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #6:
PLACE THE CENTER BENCH BOARDS ON A LEBEL SURFACE WITH THE PILOT HOLES FACING UP.
ON EACH SIDE OF THE CENTER BENCH BOARDS, PLACE ( 1 ) ONE SIDE BENCH BOARD WITH THE
PILOT HOLES CLOSEST TO THE CENTER BENCH BOARDS AND FACING UP.
STEP #7:
PLACE ( 1 ) ONE BENCH END IN POSITION AS SHOWN ABOVE BEING SURE TO ALIGN THE
PRE-DRILLED HOLES TO THE PILOT HOLES IN THE BENCH BOARDS. AFTER THE HOLES ARE
PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 2-1/2” FLAT HEAD PHILLIPS SCREW PER
HOLE TO SECURE.
NOTE: DO NOT TIGHTEN SCREW COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
#12 X 2-1/2” FLAT HEAD
PHILLIPS SCREW
www.belson.com
STEP #8:
PLACE THE REMAINING BENCH END AND CENTER BENCH END IN POSITION AS SHOWN ABOVE,
BEING SURE TO ALIGN THE PRE-DRILLED HOLES TO THE PILOT HOLES IN THE BENCH BOARDS.
AFTER THE HOLES ARE PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 2-1/2” FLAT HEAD
PHILLIPS SCREW PER HOLE TO SECURE.
NOTE: BE SURE TO TIGHTEN ALL SCREWS COMPLETELY AFTER THIS STEP.
#12 X 2-1/2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #9:
WITH BOTH PLANTER BOXES UPRIGHT, ALIGN THE PRE-DRILLED HOLES IN BENCH END, WITH
PREDRILLED HOLES IN SIDE PANELS OF PLANTER BOX. USE ( 1 ) ONE 3/8” X 4” HEX BOLT HEAD
BOLT, ( 2 ) 3/8” FLAT WASHER AND ( 1 ) ONE NYLON LOCK NUT PER HOLE TO SECURE.
** NOTE A - BENCH IS UPSIDE DOWN AND SIDE PANELS HAVE BEEN REMOVED FOR CLARITY.
** NOTE B - BOARDS HAVE BEEN REMOVED FOR CLARITY.
DO NOT REMOVE!
3/8” X 4” HEX BOLT HEAD BOLT
3/8” FLAT WASHER
Other Belson Outdoors Lawn And Garden Equipment manuals
