Beltronics RX45 User manual



 Please read both sides of these
instructions before starting your
installation.
For the easiest trouble-free
installation, install the Interface
first, and wire it to a 12-volt
switched circuit.
Then before installing the other
components, plug all of them into
the Interface and power up the
unit to confirm proper operation.
To get the best possible
performance, installation of the
Radar/Laser receiver is critical.
Although radar signals will pass
through some materials, including
plastic, laser signals will not. For
this reason the receiver must have
a clear view of the road in order to
work properly.

 
 
 Installation of this system
requires some experience and
expertise in automotive
electronics. Car Audio specialists
and many new car dealers can
install this for you.
 If you choose to install it
yourself without expertise in
automotive electronics, please
note that it can cause personal
injury or damage to your vehicle.
 If your vehicle is damaged
during installation, its safety
systems may be compromised and
could cause personal injury or
property damage.
 Improper installation may also
void RX45’s warranty.

 
 
 
Front Radar/Laser Receiver
• Miniature weather-proof Radar/Laser
Receiver
• Universal mounting bracket with
stainless steel hardware
• Built-in 16 foot shielded cable with
water proof connector
• 12 nylon wire ties to secure cable
Miniature Display Controller
• Display Controller mounts easily to
instrument pod, dashboard or console
• Optional hidden display included
Interface
• Central module connects to switched
12-volt power and ground
• All components plug directly in using
modular connections
• 3M connector taps into existing
vehicle wiring
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are
operational
• Fully compatible with Laser Shifters
Beltronics
5442 West Chester Road
West Chester OH 45069
Service 800.341.2288
www.beltronics.com
©2010 Beltronics. Beltronics, RX45, SmartShield, AutoScan, ThreatDisplay and TechDisplay are trademarks of Beltronics USA, Inc. SWS is a trademark of SWS, L.C.
Manufactured and Printed in Canada. Features, specifications and prices subject to change without notice.
NOTE: INSTALL THE RECEIVER
HORIZONTALLY AND LEVEL,
WITH A CLEAR VIEW OF THE
ROAD.
                       
Installation Manual
                         

Beltronics RX45 Installation Manual
E
C
D
A
B
A
A
F
Display Controller
1 Determine the best location for the Display
Controller in the vehicle’s interior. (Consult
customer if necessary.)
2 Remove paper backing on the backside of
the display and apply to a clean dry surface.
3 Route display cable and plug into jack
marked “Display” on the Interface.
Interface
1 Install Interface under the dash using
supplied zip-ties. DO NOT MOUNT IN
ENGINE COMPARTMENT.
2 Connect black wire (–) to ground, and red-
striped wire (+) to a switched 12-volt supply.
(If RX45 is left in the “on” position, it will
automatically power on and off with the
ignition). Use blue 3M connector (provided)
to tap into existing circuit if needed.
3 Receiver and Display Controller plug into
the Interface. Be sure to plug all cables into
the correct jacks.
Interior of Vehicle
12 Volt
Power Line
±
Front Radar/Laser Receiver
1 Determine the best location for the Radar/
Laser Receiver. The best location is typically
under the bumper, or inside the front grill of
the vehicle. For the best performance, install
the Receiver horizontally, with a clear “view”
of the road.
2 Using the built-in mounting holes on the
Receiver, or the supplied right-angle
mounting bracket, mark the hole locations.
Drill pilot holes in the vehicle if necessary.
3 Mount the Receiver using the supplied
hardware. (If right-angle mounting bracket is
used, secure the Receiver to the right-angle
bracket first, then install bracket with
Receiver to the vehicle.)
Concealed LED Display (Optional)
If a more discreet display is preferred the
included LED can be installed:
1 Drill a 1/4" hole, and install the LED clip.
2 Snap LED into clip from behind.
3 Plug the modular connector into RX45’s
Interface marked “LED.”
Receiver Cable
1 Connect the receiver cable to the receiver.
2 Route cable through the firewall, and
secure with zip-ties (included).
3 Route receiver cable into the vehicle’s
interior. If there is not a suitable opening, drill
a 13/32" or 7/16" hole.
4 Pull cable through firewall, and plug
connector into the jack labeled “Antenna” on
the Interface.
TEST
After all components are installed correctly:
1 Turn vehicle’s ignition to the “on” position.
2 Turn RX45 on by pressing the power
button located on the front of the Display
Controller.
3 RX45 will cycle through a short startup
sequence.
4 If any error messages come up, see the
Owner’s Manual for details.
5 Pull cable through the firewall and seal the
hole as needed. Use silicone sealant (not
supplied) if necessary.
NOTE:
1. Only drill hole in firewall after thoroughly
investigating location first, ensuring no other
wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
3. Do not splice cable.
NOTE:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
B
E
NOTE:
1. Make certain that the Display is clearly
visible from the driver’s position, and that the
controls can be easily accessed without
interfering with normal driving.
D
C