Bergeron By Design Height Right Chair User manual

Height Right Chair
ASSEMBLY GUIDE
WARNING:Prevent serious injury or
death from falls or sliding out.
• Never leave child unattended
• Always keep child in view
• Secure straps tightly
• Never use as a stepping stool
• Always secure child in the restraint
!
!
Parts
Left SideRight Side Foot Rest (8 pcs.) (4 pcs.)(4 pcs.)
3 4 5
(8 pcs.)
ab
c d
e
(6 pcs.) Right + Left Cap Right + Left Clip
* optional with tray
and grab rail.
Seat
a
e
d
d
dd
c
c
d
2 Back Supports Front Support 2 Metal Cross Bars Allen KeyBack
Insert a Wooden Dowel (e) into the larger hole in each of the Back Supports
and Front Support. Insert a Wood Nut (a), as shown into the inner holes of
the 3 Supports. Attach the 3 Wooden Supports as shown and insert Long
Screws (d). Loosely tighten the Long Screws into Wood Nuts through the Left
Side with the Allen Key. Labeling on the Rear Supports should be visible.
Attach the 2 Metal Cross Bars as shown and
insert Screws (c) . Loosely tighten the
Screws (c) into the Metal Cross Bars through
Left Side with the Allen Key.
Slide in the Seat and Foot Plate with the curved
edges facing forward. Make sure that the Seat
and Foot Rest are at the appropriate height for
the occupant. See the Sizing section for proper
placement of the Seat and Foot Rest.
Insert the rest of the Dowels, Wood Nuts, and
Screws as needed to attach the Right Side of
the chair. Do Not fully tighten screws.
Insert a Wood Nut (a), as shown into the inner holes of the Back. Attach the
Back as shown and insert a Long Screw (d). Loosely tighten the Long Screw
into Wood Nut through the Left Side with the Allen Key.
• Use for children 6 months and up
or when child can sit independently
• The front edge of the footrest should
never extend beyond the bottom
edge of the front supports at floor level
• SHORTER THAN
BACK SUPPORTS
FRONT
SUPPORT IS
SHORTER
HARDWARE a (3pcs.)
d (3pcs.)
e (3pcs.)
HARDWARE a (4pcs.)
d (4pcs.)
e (3pcs.)
c (2pcs.)
HARDWARE c (2pcs.)
HARDWARE a (1pcs.)
d (1pcs.)
ad
c
c
* As the child grows,
the TOP metal cross
bar CAN be removed.
Logos this side
1 2
WARNING: The child should be secured in the high chair at all times by the restraining
system. The tray is not designed to hold the child in the chair. It is recommended that the chair be
used only by children capable of sitting upright unassisted.

Bergeron By Design •15 South Second St. Dolgeville, NY 13329 •1.866.529.8407
Product Care
Clean chair with damp cloth; then wipe dry. With normal use, over time screws may loosen. Please maintain tight screws. Use chair on level surface.
Notice
When restraint system is used properly this high chair meets U.S. ASTM F-404 safety standard. Use only Height Right Chair accessories and parts. Height
Right Chair parts are not interchangable with other manufacturers’ products. Replace any worn parts immediately for safety. © 2009 Bergeron By Design.
Customer Service
Toll Free: 1.866.529.8407
International: 1.315.429.8407
Fax: [phone]
5 Year Limited Warranty
Bergeron by Design warrants to the original retail purchaser of the Height Right Chair product, that if any part or component
proves defective in material or workmanship within one year of the purchase date, the defective part will be repaired or
replaced (at Bergeron by Design’s discretion) free of charge. Warranty service may be performed by an authorized service
center or at Bergeron by Design’s discretion.
This warranty does not cover normal wear and tear, or damage caused by accident or misuse.
To exercise this limited warranty, the user should first obtain a Return Authorization Number from Bergeron By Design.
The product must be delivered charges pre-paid (UPS recommended) to the factory
or to an authorized service center, together with a copy of the original invoice, the Return Authorization Number and a
written description of the problem.
6 7 8b
8a
If the Tray or Grab accessories ARE used;
Attach the Right Clip as shown in upper picture
with 2 Small Screws (b). Repeat for Left. If Tray
or Grab accessories ARE not used; Attach
Black Caps with 2 small Screws (b). as shown in
lower picture. Repeat for Left.
• Place child in seat. Crotch strap comes up between child’s legs. Both
Lap Straps come around child from center of back and “CLICK” into
Crotch Strap. Adjust length of Lap straps to secure child in seat.
• Press center button on Crotch Strap buckle to release child from belt.
Seat and Footrest Adjustment 3 Point Belt Installation
Lap
Straps
Crotch
Strap
3 Point Belt Operation
Lap Strap “CLICK”
Crotch
Strap
Bottom of
Seat Plate
Height
• The seat is placed at optimal height when
the child’s elbows are level with the top
of the table.
• The foot plate is placed at optimal height
when the child’s foot can rest flat
on it’s surface.
Depth
• For optimal depth of the seat, position
child’s back against backrest with seat
supporting 3/4 of thigh.
• For safety, the footrest should not exceed
the front legs of the chair.
Teen / Adult Use
• Remove Seat Plate & Top metal cross bar.
• Use the Foot Rest as the Seat Plate for a
larger seating surface.
• Tighten all screws.
HARDWARE_ b (4pcs.)
When Tray or Grab accessories are installed an
audible “click” will be heard from primary lock.
Engage the second safety Latch Lever by
pushing it forward into the primary spring lock.
TIGHTEN ALL SCREWS (BOTH SIDES) IN
ORDER 1-5 _DO NOT OVER TIGHTEN!
• IF TOP METAL CROSS BAR
IS NOT NECESSARY-
START WITH # 2
Top Metal
Cross Bar
Bottom
Metal
Cross Bar
Front
Support
Back Rest
Back Leg
Supports
5
4
3
2
1
“CLICK”
Second
Safty Latch
Engaged. Primary
Spring Lock
8b
8a