Berkeley GEMINI ZHI-DRY-2238 User manual

972-926-6488
www.aycllc.com
[email protected]
CONTACT US
MODEL: ZHI-DRY-2238
HAIR DRYING
ACCELERATOR
GEMINI
INSTALLATION OF STAND AND BASE
Assemble the stand as illustrated below.
Place the machine onto the stand, and adjust it to desired height.
1.
2.
Height Adjustment knob
CAUTION:
Do not touch the surface or the safety net on the circular heating
element, as tremendous heat is produced during operation
A ground wire must be connected to the wall power supply
Machine must be serviced or repaired by a certified technician or
technician from our authorized dealer. Repaired machine must be
fully inspected in order to meet safety stands before use.
In the case where the wire is damaged or aged, new 53 (RVV)
3*0.75mm2 wire must be replaced by a certified technician from
our authorized dealer.
Thank you very much for purchasing our Hair Dryer. Please read our
user manual carefully prior to use. If the instructions are followed,
the excellent performance and operation will be clear.
4~8"
ATTENTIONS:
Do not block the cooling vent of the machine.
The machine should be turned off for 15 minutes
after it has been operating for an hour.
Please check the machine often when it is
operating.
Keep the heating plates 4"~8" away from
customer.
Do not move the machine around when it is operating.

4
+ 1 0 + 1
1
1
4
4
4
11
Timer
Boot start
Left
Time Setting1
Up
4
Time Setting
Boot start
Cool
Down
O3
Right
Middle
Start/Stop
11
CONTROL PANEL:
Use this to change the temperature of the hair dryer
Press the Temperature key will change the level each time they are pressed.
When the indicator lights are on, each level of temperature is indicated in the below table.
When the lights are off, the heating element will stop working and the fan will be off after
90 seconds
There may be slight variation in temperature depending on usage. The Standard Internal
Temperature is the temperature at approximately 5 minutes after operation. The actual
temperature may be slightly higher than displayed if it has been operating for over a
period of time.
Standard Hood
Internal
Temperature (°C)
LEVEL 0 1 2 3 4
~50 °C ~62°C ~73 °C ~85 °C
(122 °F) (143 °F) (164 °F) (185 °F)
TIME DISPLAY
②
③
①
Press once, time increases minute by minute.
Press once, time increases in ten minute increment.
④⑤⑥⑦⑧
Temperature Lever Key
⑨
⑩
⑪
Cooling Key: Press this key to cool down the device. Cooling is on when the time display is
showing C0, C1, C2.
O3 Key: Press this key to use the O3 function to accelerate skin microcirculation.
Start/Stop Key: Use this key to start or stop the device.
OPERATING MANUAL
Plug the machine into a power supply and turn the Main Power Switch on.
When “00” is displayed on the time display window, it means that the
machine is ready for operation.
When the circular heating element is not in its initial position, it will
return to its default place.
Start the device:
Press START/STOP key to start the operation.
Set the appropriate temperature and time.
Each button regulates the temperature of each heating element
Choose O3 according to the desired hair treatment.
Choose cooling key according to the desired hair treatment.
Turn off the machine
Press START/STOP key, the time display will show “00”, the fan will stop
after 3 minutes.
Timer:
Buzzer will buzz for 5 times, indicating the set time is up, and the
display will show “00”.
If “Cooling Key” is pressed, buzzer will buzz for 2 times, the display will
show “C0” to indicate the machine is cooling off.
The cooling operation can be turned off by pressing the “Cool “ key or
simply turn the switch off.
Please unplug the machine after use.
1.
2.
3.
4.
5.
FUNCTIONS
There are five separate heating plates of which the temperature can
be controlled individually by pressing buttons on the control panel.
O3 strengthens and rejuvenates the hair follicles, and helps nourish
the scalp and the hair.
TROUBLE SHOOTING
Status Reason Solution
There is noise with
the fan
The fans are dirty
There no lubricant in the part of
rotation
1.
2.
Clean the fan
Add lubricating oil to the rotation part
1.
2.
Heating element does
not produce heat
Heating element is not turned on
Wiring is loose
1.
2.
Adjust temperature to non-zero status
Right the wire
1.
2.
The fan stops working The processor is broken Replace spare parts