Berkeley OCTOPUS Instruction manual

Quick User Guide
TM
OCTOPUSOCTOPUS
(outside U.S. & Canada) [phone]
www.bvsystems.com
[e-mail]
Before You Start - Unpack and completely charge up your Octopus using the supplied power transformer and charg-
ing dock. Be sure unit is seated rmly in the charging dock so that charging LED atop unit is lit. The mini-USB port loctated
on the side of unit can be used for trickle charge and rmware updates. Check with BVS support for latest rmware and
updating instructions. Be sure to only use provided multiband antenna or other antenna authorized by BVS support. This
will ensure that unit properly scans all bands, carriers and frequencies at maximum sensitivity.
Starting Up - Before powering up, connect the antenna. Power up Octopus by pressing the white button below the
touchscreen. This same button is the only physical button on the unit and also powers down the unit by holding it in for a
few seconds. Octopus will immediately begin scanning all nearby base stations. After about 10 seconds of a startup screen,
Octopus will display the main screen of carrier choices (Octopus scans all U.S. regional carriers (over 60) but only displays
those on the carrier list screen which appears next) while continuing to scan for all nearby signals. Choose your carrier of
choice or all 4G. Allow at least 30 seconds for full scan to complete. Three small dots in the lower right corner of the screen
indicate scanning is still in progress. Tap on the gear icon (settings menu) at any time to adjust the vibrating and audible
alerts as well as check your current rmware and unit serial number. See next page of this user guide for all screens and
their paths.
Scanning and Sorting - Once Octopus has nished completely scanning, you may sort all base station signals by
either carrier, frequency or signal strength. 4G signal strength is measured in RSRQ (dB) and RSRP (dBm). Tapping the CAR-
RIER, FREQ or RSRQ/RSRP buttons will sort the list by any of those choices. If Octopus identies more than 6 unique base
stations, a PAGE down button appears for additional pages of base stations to search through. PAGE up button appears on
the next page allowing users to move through all pages. Touch the freeze button (lower left) anytime to freeze the screen(s)
to view measurements across all pages, take notes or snap a quick pic with your smartphone. This mode also saves mea-
surement data for download to PC (see user manual). Push the same button again to resume real time measurements.
Choosing Your Base Station - Once you have located the base station of interest, touch it to take you to the ac-
tive signal carrier measurement screen. From this screen you can view the channel number and realtime signal strength
as you move around and also to align external antennas to nearby base stations. Single measurement screen allows users
to toggle between RSRP and RSSI measurments in dBm as well as view RSRQ without having to leave this screen. A thin
watermark line above the vertical signal strength bar indicates peak measurement observed during the entire session. Tap
the CID button to view more information about this particular base station.
Antenna Alignment - Disconnect your included omni directional SMA antenna and connect directly to your mounted
(or soon to be mounted) antenna xture while viewing the single carrier screen. Begin with broad sweeps and then turn
your antenna slower to ne tune adjustment so that it is pointing directly to the base station you want off in the distance.
Once your signal strength is at maximum, install and tighten your permanent antenna and connect it directly to your cell
booster. You can now move on to scan more base stations and install more cell boosters if needed.

SORT THROUGH ONLY AT&T BASE STATIONS BY FREQUENCY, RSRQ OR RSRP (SHOWN)
SORT THROUGH ONLY VERIZON BASE STATIONS BY FREQUENCY, RSRQ OR RSRP (SHOWN)
SORT AMONG ALL 4G CARRIERS BY RSRP (SHOWN), RSRQ OR FREQUENCY
DIRECT MEASUREMENT OF AT&T 4G LTE BASE STATION IN RSRP. TAP RSSI BUTTON TO SWITCH TO RSSI MEASUREMENTS. VIEW ADDITIONAL INFO ABOUT THIS PARTICULAR BASE STATION BY TAPPING THE CID BUTTON.
CHOOSE CARRIER DIRECTLY OR ALL 4G OR ALL 3G UMTS BASE STATIONS. UNIT SCANS ALL 4G IN BACKGROUND BY DEFAULT
ACCESS SETTINGS MENU AT ANYTIME TO ADJUST ALERTS
SORT THROUGH ONLY T- MOBILE BASE STATIONS BY FREQUENCY, RSRQ OR RSRP (SHOWN) TOUCH SNOWFLAKE BUTTON ANYTIME TO FREEZE ALL
CURRENT SCREENS FOR VIEWING MEASUREMENTS AND STORING THOSE SCREENS INTO INTERNAL MEMORY. MEA- SUREMENT DATA CAN BE DOWNLOADED TO PC FOR FUR- THER ANALYSIS - SEE USER MANUAL FOR INSTRUCTIONS. OCTOPUS’ INTERNAL DATA BUFFER IS OVERWRITTEN EACH TIME YOU PUSH THE SNOWFLAKE BUTTON. YOU MAY NAVIGATE TO ANY PAGE FOR VIEWING WHILE THIS MODE IS ENGAGED. TAP BUTTON AGAIN TO RESUME REAL TIME MEASURMENTS.
VIEW THIS ADDITIONAL CID MEASUREMENTS FOR A SPE- CIFIC BASE STATION.