Bermuda 400 User manual

Instruction Manual
Ideal for outdoor water features
Feature Pumps
IMPORTANT: Please read this instruction manual carefully before
using this product. Keep the manual safe for future reference.
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 1 28/09/2020 14:32:20

2
Thank you for purchasing a Bermuda outdoor Feature Pump. Feature Pump
is specifically designed to power a variety of self-contained water features
and connects quickly and simply to flexible pipes and hoses. Each pump
includes flow control on the pump body, to enable water feature adjustment,
making the flow of water just right. To ensure that this product is safely and
correctly used and at its optimal performance, please read this instruction
booklet carefully before use.
Attention
1. Keep out of the reach of children.
2. A drip loop should be installed in the cable, to ensure that water cannot
travel down it and into an electrical socket.
3. An RCD (of which the rated working current is not over 30mA) must be
installed when using the pump, and the power socket must be connected
to an earth.
4. Bermuda Feature Pumps are designed for under water use only. Running
the pump dry, without water inside the pump, is strictly prohibited. Dry
running may also cause irreparable damage, and invalidate any warranty.
5. The device must not be used to pump any flammable liquids or water with
a temperature higher than 35⁰C.
6. Always disconnect the power supply when handling, servicing or
maintaining the pump.
7. Do not attempt to unplug the pump or disconnect from the power supply
with wet hands.
8. Do not carry or retrieve the pump from the water feature by pulling the
electrical cable.
9. The power cable cannot be replaced. If the power cable becomes damaged
near to the pump body it cannot be replaced, and electricals are sealed
inside the unit to make them waterproof.
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 2 28/09/2020 14:32:20

3
Features
• Highly insulated and water proof.
• New, high performance impeller design.
• Built-in overcurrent and overheat protection.
• Multi-functional design, suitable for water filters, fountains or pumping
water in a variety of situations.
• Simple to use and maintain.
• Steady and quiet performance.
Usage
Suitable for outdoor water features only. Can be run continuously, 24 hours
per day.
1. The device should be placed in enough water to ensure that the pump
body is always covered. The water feature hose should be connected to the
pump outlet, which will then feed water to the outlet in the feature. Hose
clips (not supplied) may be used for extra fastening, but are not supplied.
2. The pump output is adjustable. To turn water flow up or down slowly
turn the disc on the front of the pump either clockwise or anti-clockwise,
watching water output as you do so.
3. When first connected to the power, spend 30 minutes checking that the
pump is running as it should, steady, normal, and without any abnormal
flow, or fault. Check connections to the water feature to ensure there are
no leaks.
Maintenance
Regularly inspect and clean the pump housing to make sure it has not
accumulated too much dirt, algae and leaves. Visibly reduced pump flow is a
strong indicator that either the pump intake is nearly completely blocked, or
the hose or water feature is blocked, and needs cleaning. Always check that the
Feature Pump is submerged in water. Small water reservoirs can lose water
rapidly through evaporation, causing the pump to run dry, and flow to stop.
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 3 28/09/2020 14:32:20

4
Cleaning
Step 1: Remove the front casing from the pump by squeezing the sides and
pulling it away.
Step 2: Turn the impeller housing anticlockwise to expose the impeller inside.
Step 3: Take care when handling the ceramic impeller shaft. This is not
covered by warranty. Ensure it is clean, and not cracked or broken.
Step 4: Inspect the impeller and clean if necessary. All blades should be intact
and the magnet clean, intact and not cracked or warped.
Step 1 Step 2
Step 3 Step 4
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 4 28/09/2020 14:32:21

5
Trouble shooting
1. If the pump is not working after being connected, please check if the plug
is loose, if it has been properly wired into the plug, RCD plug or outdoor
switchbox, and that the plug and cable are not damaged. Never dismantle
the pump by yourself if malfunction occurs. Check that the RCD has been
reset and power to outdoor electricals is switched on, and not tripped or
fused.
2. If the motor of the pump is running but with less water flow or water
pressure, check that the pump housing is not already blocked by too much
dirt and leaves, and that the Head Max (height of water it is pumping to,)
has not been exceeded.
3. Check that there is sufficient water in the water feature reservoir to ensure
that the pump is under water at all times.
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 5 28/09/2020 14:32:21

6
Outlet
Seal ring
Axle sleeve
Shaft
Pump
Body
Impeller
Rotor cover
Front cover
Specifications
MODEL BER CODE OUTPUT POWER HMAX HOSETAILS DIMENSIONS
400 BER0001 350lph / 77gph 6W 0.8m 13mm 69 x 54 x 82mm
750 BER0057 750lph / 165gph 12W 1.5m 13mm 75 x 57 x 92mm
1000 BER0058 1,000lph / 220gph 16W 1.8m 16mm 89 x 70 x 111mm
1500 BER0059 1,500lph / 330gph 25W 2.5m 19mm 104 x 93 x 140mm
2000 BER0392 2,000lph / 440gph 43W 3.0m 19mm 118 x 101 x 158mm
3000 BER0083 3,000lph / 660gph 68W 3.5m 25mm 132 x 106 x 172mm
4000 BER0084 4,000lph / 880gph 75W 3.0m 25mm 132 x 106 x 172mm
Exploded view
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 6 28/09/2020 14:32:21

7
Guarantee
This product is guaranteed against defects in material and workmanship
for one year from the date of purchase, under normal usage. The
guarantee DOES NOT APPLY in case of improper use, negligence, lack of
maintenance or accidental damage to the pump. If the pump fails due to a
manufacturing fault within this period it will be either repaired or replaced
free of charge. Moving parts or wearable parts including the impeller and
any washers or O rings are not covered by the guarantee and are available
to order from your Bermuda retailer.
Should your Bermuda product stop working refer first to trouble shooting
and if this does not help, return the product to the place of purchase.
Liability is limited to replacement of the faulty product only. No other costs
will be reimbursed. This guarantee is not transferable and does not affect
your statutory rights.
Do not attempt to tamper with or access electrical components inside the
pump body. Doing so will invalidate the warranty.
The manufacturer or supplier shall not be responsible, or held liable for any
damages caused by defective components or materials of this product, or
for loss incurred by interruption of service, or any consequential/incidental
damages and expenses arising from the production, sale use or misuse of
this product or any other consequential loss.
Any warranty claim must be accompanied by a valid, dated proof of
purchase. Evolution Aqua, Bermuda, its distributors and dealers shall not
be held liable for any loss of fish, plants or any other livestock as a result of
any failure or defect of this product.
The installation and use of your product outside of our recommendations
as printed in this manual may also void the warranty.
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 7 28/09/2020 14:32:21

www.bermudawatergardens.com
BERMUDA an Evolution Aqua brand.
Evolution House, Kellet Close, Wigan, Lancashire, WN5 0LP
DISTRIBUTED BY: Certikin, Witan Park, Avenue 2,
Station Lane Industrial Estate, Witney, Oxfordshire, UK, OX28 4FJ
Feature Pumps - Instruction Manual - FP Pumps 2021.indd 8 28/09/2020 14:32:21