Bernini Table guard fly fan User manual

January 2021 © Yeiser Research & Development LLC and Bernini Fountains® Trade names, product names and logos

used in this document are the trademarks or registered trademarks of Yeiser Research & Development LLC, Santee, CA 92071

Table Guard Fly FanTM Instructions

ASSEMBLY:

Figure 2 Figure 3

Figure 4

Figure 5 Figure 6 Figure 7

Figure 1

Battery Installation:

Step 1: Remove the Table Guard Fly FanTM from the packaging (Figure 1).

Step 2: Open the Battery Compartment Door (Figure 2 A ). The Battery Compartment Door swings open (Figure 3 A ).

Step 3: Insert 2 AA Batteries into Battery Compartment (Figure 3 B ) (Batteries not included, for best results use fresh batteries).

Step 4: Close the Battery Compartment Door (Figure 4 A ). The Battery Compartment Door has 2 clips that t into 2 corresponding square holes. Swing and snap closed (Figure 5 A ).

Step 5: If you wish to hang the Table Guard Fly FanTM from the ceiling, a built in hook on the base of the fan (Figure 7 A ) allows it to hang upside down, and a notch in the hook

ensures it will hang straight.

Please Note:

1. Do not mix old and new batteries.

Do not mix alkaline, standard (Carbon-zinc),

or rechargeable (Ni-Cd, Ni-Mh, etc) batteries.

001247 BSFI rev v2h us

Santee, California 92071 | World Wide Patents Pending | Email: [email protected] | On the web: www.berninifountains.com

Facebook & Pinterest: Bernini Fountain Company | Instagram: @berninifountains

Made in China | Designed in the USA

LIMITED ONE YEAR WARRANTY

This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This product has a one year limited warranty on all

materials and workmanship. Bernini® warrants the original purchaser of this product that the product will be free from manufacturing defects in workmanship and

material for a period of one (1) year from the date of original purchase. If within one (1) year this product fails due to defect in material or workmanship, Bernini® will

repair, replace or supply any defective part at their discretion. The purchaser must contact Bernini® and provide a description of the defective part, including digital

pictures if requested, with the original purchase documentation as validation of warranty coverage. This warranty does not cover or apply to: (a) damage to the

product due to misuse, mishandling, or abuse, (b) products not used in accordance with instructions, (c) product not assembled or installed according to instructions,

and (d) normal wear and tear. Call us for assistance at +1 (619) 449-2392 or you can email us at customercare@

berninifountains.com

or mail us at: 9545 Pathway

Street, Santee, CA 92071, Our Customer Care Department is available: Monday - Friday 8:30am to 4:00pm PST / 11:30am - 7:00pm EST

Operation:

1. When the Table Guard Fly Fan is turned on (Figure

6 A ), it will run for 4 hours and then automatically

shut off. After 4 hours you can restart your Table

Guard Fly Fan by turning the unit off and back on.

The Table Guard Fly Fan will then run for another 4

hours. The Table Guard Fly Fan can be turned off

at any time turning the switch to the off position.

Congurations:

Configuration 1. When the Table Guard Fly Fan

operates in Configuration 1 mode, it creates a 2

Dimensional spatial plane (Figure 8).

Configuration

In this configuration the Table Guard

Fly Fan creates a 3 Dimensional spatial plane further

increasing its effective area (Figure 9 & 10). Simply lift

up the two short blades (Figure 9 A & B ). Slide the

two blades together where the slot is cut in the middle

of the blades (Figure 10 A & B ). This locks the two

blades together for 3 Dimension operation.

Please read first before returning:

Please call us for assistance at 1-619-449-2392 or email us at customercar[email protected]. Our Customer Care Department is available: Monday - Friday