BLAUBERG VENTO Expert A50-1 W User manual

SMART
VENTO Expert A50-1 W
VENTO Expert Duo A30-1 W
CONNECTION TO SMART HOME
OPERATION MANUAL
EN

2
www.blaubergventilatoren.de
VENTO Expert
CONTENTS
PURPOSE
Purpose .................................................................................................2
Network parameters..............................................................................3
Control commands................................................................................3
Feedback ..............................................................................................4
A smart home is controlled only by the designated master device. All other devices such as telephones and the smart home system
are slaved to the master one via WiFi. The master automatically transmits control signals to the slaves.
A wireless network can be arranged in two ways:
1. A master device with its integrated Wi-Fi access point with a maximum of four slave devices connected.
However, if all the four connection slots of the master access point are in use, the master access point becomes inaccessible by a phone
or the smart home system.
2. Master devices, slave devices, phones and smart home system connect to a common router access point via Wi-Fi
In this case the master can simultaneously handle up to 32 slave connections and the smart home system. You can also connect several
master devices to the router network to enable zone-specific control.
The connection is set up by launching the Vents TwinFresh.exe file on your computer. Please refer to the ventilator user manual for instructions.
Master with
its WiFi
access point
Slave №1 Slave №2 Slave №3 Mobile
device
Wi-Fi router
Master Slave №1 ... ... Slave №32 Mobile
device
Mobile
device

www.blaubergventilatoren.de
3
VENTO Expert
The unit is controlled via UDP transport protocol.
Master device IP address is
• 192.168.1.4 – the master device runs without a router and has its own WiFi access point (see Connection diagram 1).
• Other IP – the master device connects to the router WiFi access point (Connection diagram 2). The master device IP address is set
manually by launching the Blauberg Vento.exe file on your PC.
The master device port is 4000.
Commands,
dec Description Value, dec Size, [bytes]
1Access of data for the control page (see «Mobile application») Any byte 1
2Unit activation/deactivation Any byte 1
3Unit activation/deactivation Any byte 1
4Speed selection
1 – Low
2 – Medium
3 – High
1
5Manual speed setting enabling and setup 22 - 255 1
6Air flow direction setting
0 – Ventilation
1 – Heat Recovery
2 - Air Supply
1
9Timer activation/deactivation 1 – Night mode
2 – Party mode 1
11 Humidity sensor threshold setting, [RH%] 40 - 80 1
15 Night mode timer setting, [sec] 0 – 86400 3
16 Party mode timer setting, [sec] 0 – 86400 3
17 Deactivation delay timer setting, [sec] 0 – 86400 3
21 Humidity sensor activation/deactivation Any byte 1
22 Relay sensor activation/deactivation Any byte 1
23 0-10 V sensor activation/deactivation (On/Off) Any byte 1
25 0-10 V sensor threshold setting, [%] 5 - 100 1
27 Access of data for the slave status page (see «Mobile application») Any byte 1
28 Master device search Any byte 1
30 Master device filter timer reset Any byte 1
31 Cloud server control activation 0 – Off
1 – On 1
0 1 2 3 4 5 6 7... N-2 N-1
0x6D 0x6F 0x62 0x69 0x6C 0x65 Command1 Value1 Command n value n 0x0D 0x0A
N is the packet size.
Example of unit activation/deactivation and low speed selection
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x03 0x04 0x01 0x0D 0x0A
Example of «Ventilation» air flow direction setting
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x06 0x00 0x0D 0x0A
Example of night mode timer setting: 24 hours, 00 minutes, 00 seconds
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x03 0x04 0x01 0x0D 0x0A
NETWORK PARAMETERS
CONTROL COMMANDS

4
www.blaubergventilatoren.de
VENTO Expert
0123456 7...
0x6D 0x61 0x73 0x74 0x65 0x72 Parameter1 value1 … Parameter n value n
FEEDBACK
Parameters,
dec Description Value, dec Size, [bytes]
3Device status (On/Off) 0 – Off
1 – On 1
4Selected speed
1 – Low
2 – Medium
3 – High
4 – Manual
1
5Manual speed setting value 22 - 255 1
6Air flow direction
0 – Ventilation
1 – Heat Recovery
2 – Air Supply
1
8Current humidity level, [RH%] 39 - 90 1
9Operation mode
0 – Regular
1 – Night mode
2 – Party mode
1
11 Humidity sensor activation threshold, [RH%] 40 - 80 1
12 Alarm status (emergency stop)(status bar) 0 – No
1 – Yes 1
13 Relay sensor status (status bar) 0 – No
1 – Yes 1
14 Party mode / night mode timer countdown, [sec] 0 – 86400 3
15 Current night time mode timer setting, [sec] 0 – 86400 3
16 Current party mode timer setting, [sec] 0 – 86400 3
17 Current deactivation delay timer setting (boost mode), [sec] 0 – 86400 3
18 Filter end of life message (status bar) 0 – 86400 1
19 Humidity sensor status (status bar) 0 – No
1 – Yes 1
20 BOOST mode after any sensor response (status bar) 0 – No
1,2 – Yes 1
21 Humidity sensor 0 — Off
1 – On 1
22 Relay sensor 0 — Off
1 – On 1
23 0 – 10 V sensor 0 — Off
1 – On 1
25 0 – 10 V sensor activation threshold, [%] 5 - 100 1
26 0 – 10 V sensor status (status bar) 0 — Off
1 – On 1
27 Slave device search 0 – offline
>0 – online 32
28 Response to «Slave device search» request IP address 4
31 Cloud server control activation status 0 — Off
1 – On 1
37 0 – 10 V sensor current status 0 – 100 1

www.blaubergventilatoren.de
5
VENTO Expert
There are four types of feedback packets:
1. Control page data. Parameters: 3,9,12,19,13,26,4,5,6,8,14,18,20,37
2. Settings page data. Parameters: 11,21,22,23,15,16,17,25,31
3. Slave device search data: Parameters: 27
4. Response to «Slave device search» request. Parameters: 28
Feedback packet 1 is sent in response to control commands 1,3,4,5,6,9 and 30.
Feedback packet 2 is sent in response to control commands 2,21,22,23 and 31.
Feedback packet 3 is sent in response to control command 27.
Feedback packet 4 is sent in response to control command 28.
Example of data request for the control page
Request:
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x01 0x0D 0x0A
Response:
0x6D 0x61 0x73 0x74 0x65 0x72 0x03 0x01 0x09 0x00 0x0C 0x00 0x13 0x00
0x0D 0x00 0x1A 0x00 0x04 0x02 0x05 0x3C 0x06 0x00 0x08 0x32
0x0E 0x00 0x00 0x00 0x12 0x00 0x14 0x00
Example of data request for the settings page
Request:
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x02 0x0D 0x0A
Response:
0x6D 0x61 0x73 0x74 0x65 0x72 0x0B 0x46 0x15 0x01 0x16 0x01
0x17 0x01 0x0F 0x00 0x70 0x80 0x10 0x00 0x38 0x40 0x11 0x00 0x07 0x8
0x19 0x32
This response displays the night mode timer setting: 08:00:00, party mode timer setting: 04:00:00, delay timer setting: 00:30:00 and other
parameters.
Example of data request for the slave device search page
Request:
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x1B 0x0D 0x0A
Response:
0x6D 0x61 0x73 0x74 0x65 0x72 0x1B 0x6E 0x69 0xB4 0xC8 0xAA 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Example of slave device search
Request:
0x6D 0x6F 0x62 0x69 0x6C 0x65 0x1C 0x0D 0x0A
Response:
0x6D 0x61 0x73 0x74 0x65 0x72 0x1C 0xC0 0xA8 0x00 0x02
This response displays the master device IP address which is 192.168.0.2

www.blaubergventilatoren.de
VENTO_Expert(DUO)_W_SmartHouse_v.1(1)_EN