Bertazzoni KT Series User manual

WWW.BERTAZZONI.COM
BERTAZZONI
INSTRUCTIONS D’INSTALLATION ET D’UTILISATION
HOTTES MURALES T-FORME
BERTAZZONI
EN
FR
INSTALLATION AND USER MANUAL
WALLMOUNT T-SHAPE DESIGN HOODS
KT..XT

CONTENTS
Section Page
IMPORTANT SAFETY INSTRUCTIONS 3
RANGE HOOD DIMENSIONS 6
INSTALLATION HEIGHT REQUIREMENTS 7
PARTS 8
TOOLS NEEDED 10
VENTING METHOD 11
INSTALLING 12
CHOOSING VENTING METHOD 17
ATTACH VENTING: VENTED 18
ATTACH VENTING: RECIRCULATING 22
CONNECTING HOUSE POWER 26
OPERATING THE CONTROLS 27
CLEANING STAINLESS STEEL 29
CARING FOR FILTERS 29
REPLACING THE ACTIVATED CHARCOAL FILTER 30
REPLACING BULBS 30
WIRING DIAGRAM 31
WARRANTY 32

3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START INSTALLING
THIS Range Hood
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or medium setting.
b) AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.CrepesSuzette,
CherriesJubilee,PeppercornBeefFlambé).
c) Cleanventilatingfansfrequently.Greaseshouldnotbeallowedtoaccumulateonfanorlter.
d)Useproperpansize.Alwaysusecookwareappropriateforthesizeofthesurfaceelement.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASEFIRE,OBSERVETHEFOLLOWING*:
a) SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturno󰀨theburner.
BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATEAND
CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DONOTUSEWATER,includingwetdishclothsortowels-aviolentsteamexplosionwillresult.
d) UseanextinguisherONLYif:
1. YouknowyouhaveaClassABCextinguisher,andyoualreadyknowhowtooperateit.
2. Thereissmallandcontainedintheareawhereitstarted.
3. Theredepartmentisbeingcalled.
4. Youcanghttherewithyourbacktoanexit.
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING-TOREDUCETHERISKOFFIREORELECTRICSHOCK,donotusethisfanwithany
solid-state speed control device.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. Usethisunitonlyinthemannerintendedbythemanufacturer.Ifyouhaveanyquestions,
contact the manufacturer.
2. Beforeservicingorcleaningunit,switchpowero󰀨atservicepanelandlocktheservicedi-
sconnecting means to prevent power from being switched on accidentally. When the service
disconnectingmeanscannotbelocked,securelyfastenaprominentwarningdevice,such
asatag,totheservicepanel.
CAUTION:ForGeneralVentilatingUseOnly.DoNotUseToExhaustHazardousorExplosive
Materials and Vapors.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccordance
WithAllApplicableCodesAndStandards,IncludingFire-RatedConstruction.
2. Su󰀩cientairisneededforpropercombustionandexhaustingofgasesthroughtheue
(chimney)offuelburningequipmenttopreventbackdrafting.Followtheheatingequipment
manufacturer's guideline and safety standards such as those published by the National Fire
ProtectionAssociation(NFPA),andtheAmericanSocietyforHeating,RefrigerationandAir
ConditioningEngineers(ASHRAE),andthelocalcodeauthorities.
3. Whencuttingordrillingintowallorceiling,donotdamageelectricalwiringandotherhidden
utilities.
4. Ducted fans must always be vented to the outdoors.

4
ALL WALL AND FLOOR OPENINGS WHERE THE Range Hood IS INSTALLED MUST BE
SEALED.
This Range Hood requires at least 24" of clearance between the bottom of the Range Hood and the
cooking surface or countertop. This hood has been approved by ULat this distance from the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops and
combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface
or countertop. Consult the cooktop or range installation instructions given by the manufacturer before
making any cutouts.
MOBILEHOMEINSTALLATIONTheinstallationofthisRange Hoodmustconformtothe Manufactured
HomeConstructionandSafetyStandards,Title24CFR,Part3280(formerlyFederalStandardforMobile
Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements"
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOT obstruct the ow of combustion and ventilation air.
• Failure to follow venting requirements may result in a re.
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either through the
wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to provide e󰀩cient
performance. Thesizeof the ductwork should be uniform. Do not install two elbows together. Use duct
tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening around
the cap.
Flexibleductworkisnotrecommended.Flexibleductworkcreatesbackpressureandairturbu-
lence that greatly reduces performance.
Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts. Do
not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame
must be constructed.
WARNING-ToReduceTheRiskOfFire,UseOnlyMetalDuctwork.
CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do
notventexhaustairintospaceswithinwallsorceilingsorintoattics,crawlspaces,orgarages.
Cold Weather installations
An additional back draft damper should be installed to minimize backward cold air ow and a nonmetallic thermal
break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper
should be on the cold air side of the thermal break. The break should be as close as possible to where the vent
system enters the heated portion of the house.

5
ELECTRICAL REQUIREMENTS
A120volt, 60HzAC-only electricalsupply isrequiredon aseparate 15amp fusedcircuit. Atime-delay
fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with
the electrical rating of this unit as specied on the serial/rating plate located inside the unit near the
eld wiring compartment.
• Electrical ground is required on this Range Hood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO
NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. Afuse in the neutral or
grounding circuit could result in electrical shock.
• Check with a qualied electrician if you are in doubt as to whether the Range Hood is
properly grounded.
• Failure to follow electrical requirements may result in a re.
WARNING
!
StateofCaliforniaProposition65Warning(USonly)
WARNING
This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov

6
RANGE HOOD DIMENSIONS

7
INSTALLATION HEIGHT REQUIREMENTS
MIN. 24" OVER ELECTRIC
MIN. 30" OVER GAS
Min. 24" Min. 30"

8
PARTS
REF. PART QTY
AHood body 1
BTelescopic Lower Chimney 1
CTelescopic Upper Chimney 1
DChimney Brackets 2
EDamper Flaps 2
FHood wall Brackets 1
MDuctless Diverter 1
NRemote Control 1
REF PART
GPozi Screws 3/16" x 1 3/4" 6
HPozi Screws (1/8" x 3/16") 2
ITorx Screws 1/8" x 7/16" 4
LTorx Screws (1/4" x 2 3/4") 2
PARTS INCLUDED

9
B
A
F
C
D
E
M
N

10
PARTSNEEDED(NOTINCLUDED)
PARTS(cont.)
PART
6" Round Metal Ductwork
Drywall plugs or other suitable wall fasteners based on your instal-
lation.
Foil tape
TOOLS NEEDED
TOOL
Tape Measure
Pencil
Electric Drill with 5/16" Drill Bit
Phillips Screwdriver
Torx Screwdriver
Metal sheers
Work gloves
ACCESSORIES AVAILABLE
ACCESSORY SKU#
Replacement Activated Charcoal Filter # 901497
High Ceiling Chimney Kit - Upper and Lower Chimney Flue to replace
the original ue's to t up to 11' ceilings # 901583
Ba󰀪e lter kit # 901582

11
VENTING METHOD
VENTED
RECIRCULATING
1
Requires purchase of
Activated Charcoal
Accessory kit # 901497.
Horizontal
Vertical
6 "

12
INSTALLING
DRAW CENTER LINES
Draw a vertical line Xon the supporting wall to the ceiling or upper limit,
at the center of the area in which the hood will be installed.
Draw a horizontal line Ywhere the bottom edge of the hood will be
located, a minimum of 24" above an electric cooking surface and 30"
above a gas cooking surface.
2
Y
X
MIN. 24" OVER ELECTRIC/MIN. 30" OVER GAS Y

13
1. Place a bracket D on the wall as shown about 1/8" from the ceiling or
upper limit, aligning the center (notch) with the vertical reference line X
and mark the wall at the centers of the holes in the bracket.
2. Place the second bracket D on the wall as shown, below the rst
bracket, at the height of the upper chimney section Csupplied and
aligning the center (notch) with the vertical line.
3. Mark the wall at the centers of the holes in the bracket and mark the
point 1 and 2 for the Hood Body installation as shown(12 5/8" from the
horizontal line and 4 9/16" from the vertical line).
4. Drill ø 5/16" holes at all the center points marked (point 1,2,3,4,5,6) as
shown.
3
D
C

14
4
5
I = 6x
I = 6x
2X
Installation screws provided must be secured with wall plugs (purchase separately).
Insert the two screws Gsupplied with the hood into the Wall Bracket Fas shown
and do not tighten all the way to wall leaving 3/16" of the screw heads exposed.
F
G
Phillips Screwdriver

15
I = 6x
6
7
Usea level toinsure that Wall Bracket Fislevel and thenfully secure the twoscrews.
Hook the hood body onto the hood wall bracket F.
F
A
F

16
8Tighten the 2 screws Has shown.
H
Phillips Screwdriver

17
CHOOSING VENTING METHOD
VENTED
RECIRCULATING
Go to Pg.18
Go to Pg.22

18
1Install the Damper aps Ethatare includedwith hoodby snappingthe tabsinto place
inside the top of the hood before connecting ductwork.
ATTACH VENTING: VENTED
E
Install Roof or Wall Cap purchased separately. Connect the 6" metal ductwork to the
Roof or Wall Cap and then attach ductwork. Seal with foil tape.
2

19
3Install the 2 Chimney brackets Dto the middle and upper holes and secure with
screws Gas shown.
L = 4x
G
D
D
Phillips Screwdriver

20
4
5Secure the sides to the brackets by using the 4 screws I.
Slightly widen the two sides of the upper chimney Cand hook them behind the
brackets D, making sure that they are well seated.
N = 4x
D
C
C
I
Torx Screwdriver
D