Binatone SPEAKEASY COMBO 2005 TRIPLE User manual

Before operating thisset,
please read theseinstructions carefully.
THE CORDLESS HANDSET IS NOT DESIGNED FOR
MAKING EMERGENCY TELEPHONE CALLS WHEN THE
POWER FAILS, BUT IF THERE IS A POWER FAILURE,
YOU CAN STILL USE THE BASE AND THE CORDED
HANDSET TO MAKE AN EMERGENCY CALL.
USER GUIDE
Speakeasy Combo 2005 Twin
Monday to Friday from 9:00am to 5:00pm
Tel: [phone]
**Please note that all calls are charged at local rate
Or visit our website: www.binatonetelecom.com
Helpline (for UK only)
Speakeasy Combo 2005 Triple

TECHNICAL DETAILS
Standard
Frequency range
Channel bandwidth
Operating range
Operating time
Temperature range
Digital Enhanced Cordless
Telecommunication (DECT)
1.88 to 1.9GHz (bandwidth = 20 MHz)
1.728 MHz
Up to 300m outdoors; Up to 50m indoors
Standby: 100 hours, Talking: 10 hours
Battery charge time:15 hours
Operating 0 C to 40 C, Storage -20 C to 60 C
CLEANING AND CARE
Do not clean any part of your phone system with benzene, thinners
or other solvent chemicals as this may cause permanent damage which is not
covered by the Guarantee.
When necessary, clean it with a damp cloth.
Keep your hot, humid conditions
or
strong sunlight,and don't let it get wet.
Every effort has been made to ensure high standards of reliability for your
However, if something does go wrong, please
repair it yourself, but consult your supplier or the Helpline.
do
not try to
phone system away from
phone system.
Electrical power
Charger unit:
Risk of explosion if battery is replaced by an incorrect type
Dispose of used batteries according to the instructions.
Port specification
The port (connected to the mains power supply) is a SELV port with
respect to EN41003.
respect to EN41003.
The port (connected to the telephone line) is a TNV port with
Battery Information
Ten Pao - S004LB0600045 / S004LV0600045
input 100-240VAC 50/60Hz 150mA,
output 6VDC 450mA
Corded Base:
Ten Pao - S004LB0600030 / S004LV0600030
input 100-240VAC 50/60Hz 150mA,
output 6VDC 300mA
GPI - VT40AAAHC 2 x1.2V AAA size 400mAh NiMH
BYD - H-AAA400A 2 x1.2V AAA size 400mAh NiMH
CORUN - AAAJ400 2 x 1.2 AAA Size 400mAh NiMH

1
TABLE OF CONTENTS
1IMPORTANT SAFETY INSTRUCTIONS ................................................................. 4
2INSTALLING YOUR PHONE .................................................................................6
2.1 CONNECTING THE CORDED BASE STATION ..............................................................6
2.2 INSTALLING THE CORDLESS HANDSET AND CHARGING THE BATTERIES....................7
3GETTING TO KNOW YOUR PHONE ...................................................................... 8
3.1 OVERVIEW OF THE CORDLESS HANDSET................................................................8
3.3 CORDLESS HANDSET MENU STRUCTURE...............................................................11
3.4 CORDED BASE STATION........................................................................................12
3.5 TEXT AND DIGIT ENTRY TABLE .............................................................................. 14
4USING YOUR PHONE...........................................................................................15
Using a cordless handset:
4.1 MAKE A CALL ....................................................................................................... 15
4.1.1 PREPARATORY DIALLING ..................................................................................... 15
4.1.2 DIRECT DIALLING ................................................................................................ 15
4.1.3 CALL FROM THE PHONEBOOK .............................................................................. 15
4.1.4 CALL FROM THE CALL LIST .................................................................................. 15
4.1.5 CALL FROM THE REDIAL LIST................................................................................ 15
4.1.6 CALL TIMER ........................................................................................................ 15
4.2 ANSWER A CALL...................................................................................................15
4.3 END A CALL.......................................................................................................... 16
4.5 ADJUST EARPIECE AND HANDSFREE VOLUME .......................................................16
4.6 MUTE A CALL........................................................................................................
4.7 TURN OFF THE HANDSET RINGER ..........................................................................16
4.8 TURN ON THE KEYPAD LOCK................................................................................. 16
4.9 REDIAL LAST........................................................................................................16
4.9.1 REDIAL A NUMBER FROM THE REDIAL LIST ........................................................... 17
4.9.2 STORE A REDIAL NUMBER INTO THE PHONEBOOK ................................................ 17
4.9.3 DELETE A REDIAL NUMBER.................................................................................. 17
4.9.4 DELETE ALL REDIAL LIST ENTRIES ....................................................................... 17
4.4 ....................................................................................16HANDSET SPEAKERPHONE
16
3.2 CORDLESS HANDSET DISPLAY ICONS AND SYMBOLS ............................................10
3.5.1 CORDLESS HANDSET CHARACTER SET ............................................................... 14

2
Using the corded base:
4.10 MAKE A CALL .......................................................................................................17
4.12 ANSWER A CALL...................................................................................................18
4.13 ENDING A CALL.....................................................................................................
4.1 REDIAL NUMBER
IND THE HANDSET .............................................................................................19
MAKE AN INTERNAL CALL ...................................................................................19
INTERCOM......................................................................................................... 19
CALL ALL HANDSETS ......................................................................................... 20
TRANSFER AN EXTERNAL CALL .......................................................................... 20
MAKE A 3-WAY CONFERENCE CALL.................................................................... 20
PRIVATE PHONEBOOK (Cordless Handsets Only) ..........................................21
ADD A NEW PHONEBOOK ENTRY........................................................................... 21
SEARCH A PHONEBOOK ENTRY.............................................................................21
VIEW A PHONEBOOK ENTRY.................................................................................. 21
EDIT A PHONEBOOK ENTRY...................................................................................22
DELETE A PHONEBOOK ENTRY..............................................................................22
DELETE ALL ENTIRESPHONEBOOK .......................................................................22
CHECK THE PHONEBOOK USAGE...........................................................................22
F
4.4. Handset Speakerphone
4.1 AKE A CALL1 M ........................................................18FROM DIRECT MEMORY KEYS
IRECT THE LAST ...................................................................... 18
4.1 IRECT ........................................................................................18MEMORY KEYS
4.15.1 ........................................................ 18SAVING NUMBER IN DIRECT MEMORY KEY
CALLER DISPLAY (NETWORK DEPENDENT - Cordless Handsets Only).......23
VIEW THE CALL LIST ............................................................................................. 23
STORE A CALL LIST NUMBER INTO THE PHONEBOOK............................................. 23
DELETE AN ENTRY IN THE CALL LIST .....................................................................24
DELETE ALL ENTIRESCALL LIST ...........................................................................24
VIEW THE DETAILS OF THE CALL LIST ENTRY.........................................................24
18
4 D
5 D
5PAGING AND INTERCOM USE (For Multi Cordless Handset Systems)..........19
5.1
5.2
5.2.1
5.2.2
5.2.3
5.2.4
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7
7.1
7.2
7.3
7.5
7.4

3
PHONE SETTINGS (Cordless Handsets Only)...................................................25
DATE AND TIME SETTINGS.....................................................................................25
CHANGE THE DATE FORMAT ................................................................................ 25
CHANGE THE TIME FORMAT................................................................................. 25
SET THE TIME ..................................................................................................... 25
SET THE DATE ....................................................................................................26
ALARM SETTINGS..................................................................................................
TURN ON/OFF THE ALARM.................................................................................... 26
SET THE ALARM TIME ......................................................................................... 27
HANDSET SETTINGS.............................................................................................. 27
RINGER SETUP ...................................................................................................
SET ALERT TONES .............................................................................................. 28
SET THE HANDSET LANGUAGE............................................................................. 28
RENAME THE HANDSET ....................................................................................... 28
CHOOSE THE INFORMATION TO BE DISPLAYED IN IDLE........................................... 28
SET THE AUTO ANSWER ...................................................................................... 29
BASE SETTINGS....................................................................................................29
DE-REGISTER A HANDSET ................................................................................... 29
CHANGE THE DIAL MODE ..................................................................................... 29
CHANGE THE TIME ..................................................................... 30
CHANGE THE SYSTEM PIN CODE......................................................................... 30
RECALL (FLASH)
RESET YOUR CORDLESS HANDSET....................................................................... 30
REGISTRATION ....................................................................................................31
TROUBLESHOOTING ...........................................................................................32
11 ......................................................................33
12 ......................................................................................
DECLARATION OF CONFORMITY
PRODUCT GUARANTEE
26
27
34
8
8.1
8.1.1
8.1.2
8.1.4
8.1.3
8.2
8.2.1
8.3
8.2.2
8.3.1
8.3.2
8.3.3
8.3.4
8.3.5
8.3.6
8.4
8.4.1
8.4.2
8.4.3
8.4.5
8.4.4
9
10

4
1IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury,
including the following:
1) Read and understand all the instructions.
2) Follow all warnings and instructions marked on the product.
3) Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4) Keep this product away from hot, humid conditions or strong sunlight,
and don't let it get wet or use it near water (for example, near a bath tub,
5) Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
6) Unplug this product from the wall outlet and refer servicing to our
•When the power supply cord or plug is damaged or frayed.
•If the product does not operate normally by following the operating
•If the product has been dropped and the cabinet has been damaged.
•
If the product exhibits a distinct change in performance.
7) NEVER use this product outdoors during a thunderstorm. Unplug the
base from the telephone line and the mains socket when there are
8) Do not use the telephone to report a gas leak in the vicinity of the leak.
9) Use only the supplied NiMH (Nickel Metal Hydride) batteries! The
operation periods for the handsets are only applicable with the default
11) Do not use third party charging bays.
12) Make sure the batteries are fitted into the handset in the correct polarity.
13) Dispose of batteries safely. Do not immerse them in water, burn them,
Repair Centre under the following conditions:
battery capacities.
instructions.
or put them where they could get punctured.
Damage may be caused to the batteries.
storms in your area. Damage caused by lightning is not covered by the
guarantee.
shower, kitchen sink, swimming pool).
10) The use of other battery types or non-rechargeable batteries/primary
cells can be dangerous. These may cause interference and/or damage
to the unit or surroundings. The manufacturer will not be held liable for
damage arising from such non-compliance.

5
Package contents
The twin package contains the following items:
• 1 Cordless Handset
• 1 Base station
• 1 AC power adapter for the base station
• 1 Telephone line cord
• 2 Rechargeable Batteries
• 1 User manual
• 1 Charger Pod with connected AC power adapter
• 1 Corded Handset
• 1 Coiled cord for the corded handset
NOTE: If you have a Triple or Quad system, you will also have the
requisite extra cordless handsets, batteries and charger pods.
Handset - Base Connection
1) When purchased, all handsets are already registered to the base unit and
2) To use your cordless handset and base unit together, you must be able to
establish a radio link between them. The signal between the handset and
> Any large metal object, such as a refrigerator, mirror or filing cabinet,
between the handset and the base unit may block the radio signal.
> Other solid structures, like walls, may reduce the signal strength.
> Other electrical equipment may cause interference and/or affect the range.
3) Do not place close to another telephone, a TV or audio equipment - it may
cause interference.
4) Out of Range warning. If you hear a warning tone during a call, and/or the
sound in the earpiece becomes faint or distorted, you may be going out of
range of the base unit, so move nearer to the base unit within 20 seconds,
otherwise the call may be cut off.
Maximum range up to 300 metres outdoors or 50 metres indoors. Be aware
should link to it when they are all powered up.
the base is in accordance with the normal standards for a DECT phone:
that:

6
2INSTALLING YOUR PHONE
IMPORTANT
The base must be plugged into an electrical outlet at all times to work fully,
and the cordless handset will not work without it. Only use the power supply
adapters and telephone line cord supplied with the product. Others may not
2.1 Connecting the Corded Base
be compatible and may cause a hazard.
If you have a Broadband line (ADSL)
If you connect your telephone to a line with a
insert a micro-filter between the telephone
and the telephone line, otherwise you may get
interference between the telephone and the broadband,
which could cause problems.
In a home with broadband, every telephone must have a micro-filter connected,
not just the one at the telephone point that your modem is connected to.
If you need more broadband (ADSL) micro-filters, contact your broadband
1. Connect the corded
2. Plug the power adapter
handset to the base
station, using the
coiled line cord
& telephone line cord
into the sockets at the
back of the base.
provided and making
sure the plugs are
inserted fully and click
into place in the sockets
on the handset and the
side of the base.
3. Plug the power adapter into a 230Vac, 50Hz mains
socket, and the line cord into your telephone line socket.
broadband (ADSL) connection, you will need to
supplier.

(BACK)
Press to clear a character or stop the alarm if applicable, press to mute / unmute during a call.
2.2 Installing the cordless handset and charging the batteries
2) Place the 2 supplied batteries into the battery compartment with the
polarity markings as indicated.
3)
4) Put the cordless handset on the charger and charge for 15 hours
before using the handset for the first time. The handset will give a
beep when it is properly placed on the charger.
Slide the battery compartment cover back until it clicks into place.
Use only NiMH rechargeable batteries.
7
1) Slide open and remove the battery compartment cover from the
back of the handset.

8
3GETTING TO KNOW YOUR PHONE
3.1 Overview of the Handset
1 LEFT SOFT KEY (MENU/OK)
In idle mode: Press to access the main menu
In sub-menu mode: Press to confirm the selection
During a call: Press to access Intercom/
2 RIGHT SOFT KEY ( )
In main menu mode: Press to go back to idle
In sub-menu mode: Press to go back to previous
In sub-menu mode: Press and hold to go back
In editing / predialling mode: Press to clear a
character / digit
In editing / predialling mode: Press and hold to
delete all the characters/ digits
During a call: Press to mute / unmute the
microphone
In idle mode: Press to intercom another handset
UP ( )
In idle mode: Press to access the Call List
In menu mode: Press to scroll up the menu items
In Phonebook list / Redial list / Call List:
During a call: Press to increase the earpiece or speaker volume
DOWN ( )
In idle mode: Press to access the Redial List
In menu mode: Press to scroll down the menu items
In Phonebook list / Redial list / Call List: Press to scroll down the list
During a call: Press to decrease the earpiece or speaker volume
Phonebook/ Redial List/ Call List
screen
level
to idle screen
3
Press to scroll up the list
4
TALK
In idle / predialling mode : Press to make a call
In Redial list / Call List / Phonebook entry: Press to make a call to
the selected entry in the list
During ringing: Press to answer a call
5
1
5
7
8
2
4
6
9
3
10
11
During ringing: Press to decrease the ringer volume
During ringing: Press to increase the ringer volume

9
During a call: Press to end a call and go back to idle screen
In menu / editing mode: Press to go back to previous menu
In menu / editing mode: Press and hold to go back to idle screen
In idle mode: Press and hold to power off the handset
In idle mode (when the handset is powered off): Press and hold to
ALPHANUMERIC KEYPAD, * (STAR), # (HASH)
Press to insert a digit / character / * / #
* key in idle mode: Press and hold to enable or disable the keypad lock
* key during a call (in Pulse mode): Press to switch to tone mode
# key in Idle mode: Press and hold to turn on / off the handset ringer
0 key in idle / predialling / number editing mode: Press and hold to
# key in Call List mode: Press to review caller's number if applicable
6 OFF
power on the handset
7
insert a pause
SPEAKERPHONE ( )
During a call: Press to turn on / off the speakerphone.
In Idle mode / predialling mode / Redial list / Call List / Phonebook
entry: Press to make a call with speakerphone
During ringing: Press to answer a call with speakerphone
FLASH (Recall)
In idle / predialling mode: Press to insert a recall signal (also called Flash)
During a call: Press to send a recall signal (also called Flash)
EARPIECE
MICROPHONE
9
8
10
11

10
3.2 Display Icons and Symbols
The LCD display gives you information on the current status of the telephone.
(MENU)
(INT)
Scroll up / down the menu items / Phonebook list / Redial list / Call List
Steady when the handset is in range of the base. Flashes when out of
Steady when an intercom is in progress.
Flashes when there is an incoming internal call.
Indicates a call is in progress.
Indicates that handsfree is being used.
Indicates that the handset ringer is switched off.
Steady when an alarm is set. Flashes when an alarm time is reached.
Indicates that the keypad is locked.
Indicates when you have a new Voice Mail message. (This is a caller
display service and is not usually available from UK network providers.)
When not on a charger, indicates the battery is fully charged.
When on a charger, the whole icon flashes while the battery is being
When not on the charger, indicates the battery needs charging.
Flashes when low battery power level is detected, including when first
Indicates when there are more characters or numbers in front of those
Indicates when there are more characters or numbers after those
LEFT SOFT KEY function. Press MENU/OK to access the main menu.
LEFT SOFT KEY function. Press MENU/OK to confirm the current
Indicates a new call in the call list.
RIGHT SOFT KEY function. Press C/MUTE to start an intercom call.
charged, but when the battery is fully charged, only the internal block
of the icon flashes.
put on charge.
being displayed.
being displayed.
selection.
range of the base or not registered to the base.

11
In idle mode, press <MENU/OK> to go to CALL LIST, the first option in the
3.3 Cordless Handset Menu Structure
menu list.
Press <UP> or <DOWN> to go to other options in the menu list.
Press <MENU/OK> to enter a sub-menu or function.
RIGHT SOFT KEY function. Press C/MUTE to go back to the
previous menu level or cancel the current action.
RIGHT SOFT KEY function. Press C/MUTE to mute/unmute the
microphone during a call, delete characters, or stop an alarm.
Keys C / MUTE (INT)
<UP/DOWN>
Key Press
<MENU>
<UP/
DOWN>
<UP/
DOWN>
<UP/
DOWN>
<UP/
DOWN>
<UP/
DOWN>
The following keys have direct functions in idle mode:
Press <C/MUTE> to go back to the previous level.
Sub
menu Shows
EMPTY or
Then press
<MENU/OK>
for:
ADD TO PB
DELETE
DELETE ALL
Shows EMPTY or
Then press
<MENU/OK> for:
ADD
PB STATUS or
ADD
VIEW
EDIT
DELETE
DELETE ALL
PB STATUS
BS RINGER
RING VOLUME
DELETE HS
DIAL MODE
FLASH TIME
CHANGE PIN
ALARM
RING SETUP
TONE SETUP
LANGUAGE
RENAME HS
HS DISPLAY
AUTO ANSWER
DATE & TIME
PIN?
Main
Menu
CALL LIST
PHONEBOOK
BS
SETTINGS HS SETTINGS REGISTRATION DEFAULT
DETAILS
the first
Phonebook entry.
the first Call
List entry.
Shows EMPTY or
the first Redial
Shows EMPTY or
the first Call List
entry.
Shows the
available intercom
numbers, or starts
the intercom
other cordless
handsets is
Sub menu
(Press
MENU/OK
not empty)
ADD TO PB
DELETE
DELETE ALL
ADD TO PB
DELETE
DELETE ALL
DETAILS
if the list is
List entry.
ringing if only one
registered.

12
3.4 Corded Base Station
g m
2
1
3
4
6
5
7
1 STORE
In idle mode: Press to enter the Direct Memory storing mode.
2 FIND
In idle mode: Press to find/page all registered cordless handsets.
Press the button again, or press <TALK>, <OFF> or <C/MUTE> on a
Press and hold to enter registration mode.
3 FLASH (Recall)
Press to send a Recall signal (also called Flash).
4 REDIAL
In idle mode: Press to dial to the last number dialled, in speakerphone
cordless handset, to turn off the page signal.
12
8
9
11
10
During a call:
mode.

13
5 VOLUME- Press to decrease the listening volume.
Press to decrease the corded base ringer volume.
6 VOLUME+
a) During a call: Press to increase the listening volume.
b) When ringing: Press to increase the corded base ringer volume.
7 SPEAKER
a) In idle: Press to access the line in speakerphone mode.
b) During a call: Press to toggle between the speakerphone and the
c) During ringing: Press to answer a call in speakerphone mode.
earpiece mode.
8 */ TONE
a) During dialling or storing a number: Press to insert a *.
b) In Pulse dialling mode: Press to switch from pulse to tone
dialling for the rest of that call.
9# / PAUSE
a) During dialling or storing a number: Press to insert a #.
Press and hold to insert a pause (P).
10 ALPHANUMERIC KEYPAD
a) During dialling or storing a number: Press to enter digits.
11 BASE CRADLE / HOOKSWITCH
12 DIRECT MEMORY KEYS (M1, M2 and M3)
a) In idle mode: Press to dial the number stored in the memory key in
speakerphone mode.
a) During a call:
b) When ringing

14
Using a cordless handset:
3.5.1 English Character Set
Key Alphanumeric Editing
(For phonebook name editing and renaming handset)
Number Editing
(For phone number
editing, date/time
Key press 1st 2nd
3rd 4th 5th 6th 7th 8th 9th 10th
1 space - 1 1
2 A B C 2 2
3 D E F 3 3
4 G H I 4 4
5 J K L 5 5
6 M N O 6 6
7 P Q R S 7 7
8 T U V 8 8
9 W X Y Z 9 9
0 0 0, P (Pause)
* * ? / \ ( ) *
# # ‘ , - & #
Writing Tips:
1. Once a character is selected, the cursor will move to the next position
2. You can move the cursor within the text with the <UP/DOWN> keys on
3. Press <C/MUTE> to delete the last character.
4.
after a short pause.
the handset to amend the text entry.
3.
The following table shows you where each letter and punctuation character
can be found on the cordless handset, by using repeated presses of the
This will be helpful when storing a name in the handset phonebook or
renaming your handset.
In editing mode, a cursor is displayed to indicate the current text entry
position. It is positioned at the right of the last character entered.
Press and hold <C/MUTE> to delete the entire text string.
5 Text and Digit Entry Table
alphanumeric keypad.
editing)
Note: There are some different characters available if the handset language
is changed (see 8.3.3).

15
4USING YOUR PHONE
Using a cordless handset:
4.1 Make a Call
4.1.1 Preparatory Dialling
Enter the phone number and press <TALK> or <SPEAKERPHONE> to
dial the number. When entering the number, if you make a mistake,
4.1.2 Direct Dialling
Press <TALK> or <SPEAKERPHONE> to connect to the line and then enter
4.1.3 Call from the phonebook
4.1.4 Call from the Call List
Press <UP/CALLS> to go to the most recent entry in the Call List and press
<UP/DOWN> to select the desired Call List entry. Press <TALK> or
<SPEAKERPHONE> to dial out the selected Call List entry.
Press <DOWN/REDIAL> to access the redial list and press <UP/DOWN> to
select the desired redial number. Press <TALK> or <SPEAKERPHONE> to
dial out the selected redial number.
4.1.6 Call Timer
Your handset automatically times the duration of every call. The call timer
will display as soon as you answer a call or 15 seconds after dialling, and
remains on the screen for 5 seconds after the end of a call. It is shown in
4.2 Answer a Call
If the handset is not on the charger:
When the phone rings, press <TALK> / <SPEAKERPHONE> to answer
Note: If AUTO ANSWER is set ON, then lifting the handset off the charger
will answer the call automatically and no buttons need to be pressed.
a call.
hours, minutes and seconds format (HH:MM:SS).
with the <C/MUTE> key.)
press <C/MUTE> to delete digits.
the phone number. (Note: if you enter a wrong digit you cannot correct it
Press <MENU/OK> and <UP/DOWN> to access the phonebook and press
<MENU/OK> and <UP/DOWN> to select the desired phonebook entry.
Press <TALK> or <SPEAKERPHONE> to dial out the selected phonebook
entry.
4.1.5 Call from the Redial List
Note: From idle, you can also access the Call List, by pressing <MENU/OK>
twice.

When the phone rings, pick up the corded handset to talk to the caller.
4.3 End a Call
During a call connection, press <OFF> to end the call.
OR
Put the handset on the charger to end the call.
4.5 Adjust Earpiece and Handsfree Volume
There are 5 levels (VOLUME 1 to VOLUME 5) to choose from for each of
During a call:
Press <UP/DOWN> to select volume 1-5. The current setting is shown.
When you end the call, the setting will remain at the last selected level.
4.6 Mute a Call
You can talk to someone nearby without letting the caller hear you during a
call.
During a call:
Press <C/MUTE> to mute the microphone. MUTED is shown on the display,
and your caller cannot hear you.
Press <C/MUTE> again to unmute the microphone.
4.7 Turn Off the Handset Ringer
In idle mode, press and hold the < # > key to turn off the handset ringer.
The "RINGER OFF" icon is shown on the display.
If the handset ringer is off, press and hold the < # > key to turn it back on.
The "RINGER OFF" icon will disappear.
4.8 Turn on the Keypad Lock
In idle mode, press and hold the < * > key to turn on the keypad lock.
The "KEYPAD LOCK" icon is shown on the display.
In keypad lock mode, press and hold the < * > key to turn off the keypad lock.
The "KEYPAD LOCK" icon will disappear.
4.9 Redial Last
The handset saves the last 5 numbers called. If you have stored a name
in the phonebook to go with the number, the name will be displayed instead.
The most recent last number will display at the top of the redial list.
the earpiece and handsfree volumes.
During a call, you can press <SPEAKERPHONE> to alternate between
hands-free speakerphone and normal handset use.
4.4. Handset Speakerphone
16
Note: You can still answer a call when the keypad lock is on.

4.9.2 Store a Redial Number into the Phonebook
1. Follow Steps 1 and 2 in section 4.9.1.
2. Press <MENU/OK> to show ADD TO PB.
3. Press <MENU/OK> and then enter the name you want it to have in the
4. Press <MENU/OK> and then modify the number, if necessary.
5. Press <MENU/OK> to show <MELODY 1>.
6. Press <UP/DOWN> to browse the melody list. The respective melody
will be played when browsing the melody list.
7. Press <MENU/OK> to confirm, and the entry will be stored.
phonebook.
(Note: The selected melody will only be played when you receive a call
if you subscribe to Caller Display and the incoming number matches the
4.9.3 Delete a Redial Number
1. Follow Steps 1 and 2 in section 4.9.1.
2. DELETE.
3. Press <MENU/OK> to confirm, and the entry will be deleted.
4.9.4 Delete All Redial List Entries
1. Follow Steps 1 and 2 in section 4.9.1.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE ALL.
3. Press <MENU/OK> to display CONFIRM?.
4. Press <MENU/OK> to confirm. All entries will be deleted and the display
Using the corded base:
will show EMPTY.
Press <MENU/OK> and <UP/DOWN> to select
1. Pick up the corded handset or press < SPEAKER> on the corded base.
2. Enter the phone number.
4.10 Making a call
4.9.1 Redial a Number from the Redial List
1. In idle mode, press <DOWN/REDIAL> to access the redial list.
Note: If the redial list shows a name, press the < # > key to view the
2. Press <UP/DOWN> to browse the redial list.
3. Press <TALK> / <SPEAKERPHONE> to dial to the selected redial
Note: If there are no numbers in the redial list, the display shows“EMPTY”.
number.
number of this entry.
17
WARNING: There will be a 3-second delay, after picking up the corded
handset or pressing the <SPEAKER> button, before any digits
period.
stored number.)
will dial out, but any digit keys pressed during this time will still
be detected and the numbers will be dialled out after the delay

18
1. During a call, put the corded handset on the corded base cradle.
Or If you are using the speakerphone, press <SPEAKER> to end the call.
In idle mode, press <REDIAL> on the corded base. If there is a redial
number, the number will dial out in speakerphone mode.
There are 3 direct memory keys (M1 to M3) on the corded base for you to
store frequent use numbers, of up to 24 digits each.
If more that 24 digits are entered, only the first 24 digits are stored.
4.13 Ending a Call
4.14 Dialling the Last Redial Number
4.15 Direct Memory Keys
4.15.1 Saving a Number in a Direct Memory Key
Lift up the corded handset to switch the call to the earpiece mode.
1. In idle mode, press <M1>, <M2> or <M3> to dial the number stored in
the direct memory keys via speakerphone.
Note : If the selected direct memory key is empty, an error tone is emitted
4.11 Making a Call From Direct Memory Keys
Lift up the corded handset to switch the call to the earpiece mode.
1. Pick up the corded handset or press <SPEAKER> to answer the
4.12 Answering a Call
1. In idle mode, press STORE.
Press
If there is already a number in your selected direct memory
key, the new number will replace the previous number.
2.
1.
2. Enter the phone number.
Note: The Direct Memory Key stores cannot be cleared completely.
To remove a number, you can only overwrite it with a new number.
incoming call.
via speakerphone and the corded base will return to idle mode.
<M1>, <M2> or <M3> to store the number in that memory.