Bio Smart Technologies In-Wall Series Setup guide
Therapeutic Infrared Heat
.
.
B IOS MART
®
Save these
Instructions
Includes:
Product information
Thermostat options
Installation guidelines
Operating Instructions
Technical Specications
Warranty & Service instructions
Installation and Operator’s Manual
Therapeutic infrared heating systems
for a green, healthy environment
BioSmart®In-Wall Far Infrared Heaters. Feel the Difference.
BioSmart Technologies
In-Wall Series
Bio-1000F
Bio-1200F
Customer/Warranty Service: 800-595-9605
Table of Contents
Section 1 - Understanding BioSmart Infrared Technology 1
Section 2 - Unpacking 2
Section 3 - For your Safety / Warnings 2
Section 4 - Installation Requirements 2
Heater Location 3
Thermostat Location and Requirements 3
Thermostat Options 3
Section 5 - Mounting Instructions 4
New Construction 4
Retrofit Installations 4
Wiring Instructions 5
Section 6 - Operating Instructions 5
Section 7 - Maintenance Requirements 5
Section 8 - Diagnostic Information 5
Troubleshooting 6
Component Diagram 7
Component Listings 7
Schematic 8
Section 9 - Technical Specifications 8
Section 10 - Warranty & Service Information 9
Page 1
©2017 BioSmart Technologies
Section 1 - Understanding BioSmart Infrared Technology
Infrared technology is not new, however, the use of commercial infrared technology for zoned interior applications is
40
45
50
55
60
65
70
75
80
85
0 1 2 3 4 5
Temperature (Fahrenheit)
Time (Hours)
47
48
47
67
70 73
76
80
74
83
75
Faster warm-up and retention time means dramatic
energy savings with BioSmart Infrared
20 - 50% Energy savings with
BioSmart Infrared
Test booth starting
temperature
e BioSmart heater reached 75 °F
nearly 70% faster, more than 2
hours sooner, saving over 2 KWh
of electricity!
Nearly 20%
faster to 72 °F
BioSmart Far Infrared vs Standard Coil-Type Radiant Heater
Coil-Type Radiant HeaterBioSmart Far Infrared Heater Dierence in time required to reach given temperature
Page 2
Customer/Warranty Service: 800-595-9605
Section 2 - Unpacking
that all the necessary installation hardware is included. Inspect the unit for any shipping damage that may have occurred.
You should have:
mounting the faceplate along with plastic inserts to cover up the screws.
Section 3 - For your Safety / Warnings
!
WARNING
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THE HEATER
or damage the heater.
the High-limit switch
Section 4 - Installation Requirements
millivolt thermostat.
the millivolt circuit inside the heater.
Page 3
©2017 BioSmart Technologies
Heater Location
Room with single heater Room with dual heaters Room with multiple heaters
= Preferred thermostat location
Thermostat Location and Requirements
thermostat location.
Thermostat Options
The use of a simple millivolt thermostat
settings during certain hours of the day.
ranges when it comes to choosing a thermostat.
Page 4
Customer/Warranty Service: 800-595-9605
Section 5 - Mounting Instructions
New Construction
Retrofit Installations
Installation Range
12” 12”
Installation Range
Hole Size
Stud Spacing
Page 5
©2017 BioSmart Technologies
Warning
heater up-side down.
Warning
Wiring Instructions
1 2 4
Legend
1.
2.
4. High voltage relay
Section 6 - Operating Instructions
will determine your comfort levels and energy savings. Be sure to familiarize yourself with your thermostats operations and
features in order to get the most advantage from your infrared heaters technology.
Section 7 - Maintenance Requirements
Section 8 - Diagnostic Information
Overview
Page 6
Customer/Warranty Service: 800-595-9605
Troubleshooting
The heater does not
turn on
A
B
Burning smell
A
B
this also causes the heater to automatically shut-down.
The heater gets too
hot causing the high
limit switch to trip
A
B
minutes after the heater has shut off in order to cool the heater down. This test must
operation of the center fan.
Excessive fan noise A
will eliminate the two outside fans or the middle fan from the diagnosis. You must
have the unit opened up to replace a fan if necessary.
Page 7
©2017 BioSmart Technologies
Component Diagram
7
9
11
2
4
14
12
1
10
Component Listings
1.
2.
4.
7.
9.
10.
11.
12. Fans
14.
Page 8
Customer/Warranty Service: 800-595-9605
Schematic
WALL
THERMOSTAT
AC
SSR
FAN 1 FAN 2 FAN 3
PCB
FAN 1FAN 3FAN 2
Fans
Ceramic
Terminal
Block
Ceramic
Infrared
Element
Ceramic
Infrared
Element
High-Limit
Switch
Standard In-Wall 1000w
2017/5/8
010
020
030
040
170
110
120
180
Section 9 - Technical Specifications
Model BIO-1000F, BIO-1200F
plastic front cover
heat into the room.
prevents damage to the unit
Heat Type: therapeutic infrared heat
Heating Elements: 2 ceramic far infrared emitters
WARRANTY & SERVICE
and materials under normal use and service for a period of one (1) year
period BioSmart shall supply at no cost, excluding shipping, to the original purchaser, replacement parts as
and materials under normal use and service for a period of five (5) years
period BioSmart shall supply at no cost, excluding shipping, to the original purchaser, replacement elements
five (5) year warranty period, BioSmart shall provide free in-house repair service. At
will perform all necessary repairs and return the unit to the customer. Shipping cost to and from the service
Limitations
or install its products correctly.
representatives, written or oral, that are inconsistent with this written warranty, or which are misleading or
Warranty Restrictions
Warranty Claim Procedures -
BioSmart®Far Infrared Heaters
BioSmart Technologies
18324 Cook Road, Suite 1
Yelm, Washington 98597
Customer/Warranty Service:
800-595-9605
North American Distribution and Sales
BioSmart® Far Infrared Heaters
Green Technology for a Modern World
www.BioSmartSolutions.com
Warranty Registration No.
Dealer/Installer Information
This manual suits for next models
2
Table of contents
Other Bio Smart Technologies Heater manuals
