Biodrier 3D SmartDry User manual

1
Hand dryer
Automatic
High Speed

2
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Technical Specications
Item Category Performance Data
Operating Voltage 220 - 240Vac, 50Hz, 200 - 800 WATTS
Air Speed Output 75m/s, 85 m³/h
Air Output Temperature Intelligent - based on room temperature
Motor Type 18,000 rpm, 200 Watts, BLDC brushless DC motor
Decibel Rating 70 dba @ 1 mtr
Heater Element 0-600 Watts - Intelligent Heating
Heater Thermal Protection Auto Resetting Thermostat turns unit o at, 149°F (95°C)
Drying Time Under 10 seconds
Circuit Operation Infared Automatic, self adjusting
Sensor Range 100 mm
Timing Protection 25 seconds auto shut o
Drip Proof IPX2
Isolation CLASS I
Net Weight 3.3 kg
Shipping Weight 15.7 kg
Unit Size W 228 x H 278 x D 154 mm
Certicates CE, WEEE, Greenspec
Item Code Cover Type/Finish
BSD83B Brushed Stainless Steel
Thi
ti
228 mm 154 mm
278 mm

3
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
General Safety Information
WARNING
This product is intended for installation by a
qualied service person. Use AWAG No.16 solid
conductor for wiring.
Failure to properly ground unit could result in
electrical shock and/or death.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
All units must be supplied with a 3-wire service. The
ground wire must be connected with the dryers
back plate.
NOTE: Do not install dryer over wash basin.
Type Y attachment
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualied person in order to avoid a hazard.
Means for disconnection must be incorporated in the
xed wiring in accordance with the wiring rules.
Installation
Installation must be carried out by a qualied
electrician
1. Make sure power supply breaker is switched o.
Installation must be carried out in accordance with the
current edition of the local wiring regulations code
having jurisdiction. Installation should be performed
only by a qualied electrician.
NOTE: For two or more dryers, dryers should be no
closer than 24 inches (610 mm) on centre.
2. Connect supply wires to terminal block where
indicated and connect ground wire to baseplate with
ground screw.
Connections:
a. Connect the live wire (coloured red or brown) to
the terminal block marked“L”.
b. Connect the neutral wire (coloured black or blue)
to the terminal block marked“N”.
c. Connect the ground wire (coloured green or green
and yellow) to the green screw marked“ ”.
Note that the colour of live and neutral wires depends
on voltage of supply service.

4
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Installation Continued
• Before connecting to the main power install a
secondary switch with a contact distance of > 3 mm.
• This hand dryer must be earthed correctly.
• Do not install near water or in areas with high
humidity
• Ensure power is cut o before installation
1. UseanAllenkeytoremovethescrewsonbothsidesof
the hand dryer (g. 2) and remove the cover. Use the
mounting height guide and the installation template
to mark and drill 4 Ø 8 mm holes at a depth of 35 mm.
2. Fix the hand dryer backplane to the wall using
appropriate xings for the wall type.
3. Replace the cover and attach using the original
screws.
4. To install with a concealed wire knock out the pre-cut
hole in the backplate, remove the power cord, thread
through the hole and connect to the corresponding
terminals.

5
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
From oor to bottom of dryer.
Men’s Ladies Children, ages 11-17 Children, ages 3-10 Disabled
43” 41” 39” 33” 35”
109 cm 104 cm 99 cm 84 cm 89 cm
Recommended Mounting Heights
Intelligent Heating
The 3D Smart Dry automatically adjusts the heater
depending on the ambient temperature of the air
surrounding the dryer.
This means that in cold temperatures you have a
comfortable hand drying experience and in the warmer
weather you can reduce your energy consumption and
save money.
Room Temp Heater Power Total Power
< 10°C 600 w 800 w
10 - 15°C 450 w 650 w
15 - 20°C 300 w 500 w
20 - 25°C 150 w 350 w
> 25°C 0 w 200 w
Cleaning and Maintenance
All surfaces of the unit should be cleaned daily with a
soft cloth dampened with warm, soapy water. Polish
with a soft dry cloth.
DO NOT use caustic solutions or abrasive cleaning
materials on the drier.
Operation
• No touch operation.
• Shake excess water from hands.
• Place hands under the outlet, within 10 cm, to start
operation.
• Move hands back and forth through the air jets
• Stops automatically after hands are removed, or after
60 seconds.

6
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Key Description Part No.
1Cover HDS-BSD03-3159-1
2Screws HDS-BSD03-3159-2
3Filter cover HDS-BSD03-3159-3
4Sensor house HDS-BSD03-3159-4
5Sensor HDS-BSD03-3159-5
6LED HDS-BSD03-3159-6
7Air outlet bae HDS-BSD03-3159-7
8Air outlet seal HDS-BSD03-3159-8
9Terminal block HDS-BSD03-3159-9
10 Blower housing HDS-BSD03-3159-10
11 Heating element seal HDS-BSD03-3159-11
12 Heating element HDS-BSD03-3159-12
13 Power cable clamp HDS-BSD03-3159-13
14 Cable clamp HDS-BSD03-3159-14
15 Cable seal HDS-BSD03-3159-15
16 Shock absorber rubber HDS-BSD03-3159-16
17 Fitting brush HDS-BSD03-3159-17
18 Washer HDS-BSD03-3159-18
19 Base plate HDS-BSD03-3159-19
20 Motor xing plate HDS-BSD03-3159-20
21 Shock absorber ring HDS-BSD03-3159-21
22 Motor HDS-BSD03-3159-22
23 Compressing block HDS-BSD03-3159-23
24 Air ue HDS-BSD03-3159-24
25 Heat dissipation plate HDS-BSD03-3159-25
26 Control PCB HDS-BSD03-3159-26
27 PCB cover HDS-BSD03-3159-27
Parts List

7
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Diagram
ḷ䇠 ༴ᮠ ᴤ᭩᮷Ԧ ㆮᆇ ᰕᵏ മṧḷ䇠
ޡᕐ
ᰕᵏ
ᐕ㢪
䇮䇑 ᇑṨ 

FW3 LTD, Biodrier
Unit 3, Woodlands Business Park, Burlescombe, Devon, EX16 7LL
tel: [phone] • email: [e-mail]