Biodrier G-Wave User manual
1
G-Wave
Hand dryer
Automatic
High Speed
G-Wave
2
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
510mm
175mm
266mm
Technical Specications
Item Category Performance Data
Operating Voltage 220 - 240Vac, 50-60 Hz, 700 - 1200 WATTS
Warm Air Speed Output 150 m/s @ 1200 WATTS
Display LED information and alerts
Motor Type 35,000 rpm, AC motor, 2 speed adjustable
Motor Thermal Protection Auto Resetting Thermostat turns unit o, 105°C
Noise Level 58 - 80 dba @ 1 metre
Water Tank LED indicator when tank is full
Filter Sensor LED indicator when lter needs to be replaced
Air Purication Enzyme HEPA Filter H13 - simple cartridge replacement system
Air Freshener Organic moisturiser, sanitizer & air freshener with ocean breeze fragrance
Water Tank & Filter Security Sliding locking system, lock both with one touch
Drying Time Under 10 seconds
Circuit Operation Infared Automatic, self adjusting
Timing Protection 20 seconds auto shut o
Drip Proof IP33
Isolation CLASS II
Certicates CE, GS, ETL, WEEE
Net Weight 6 kg
Shipping Weight 7 kg
Unit Size 266mm W x 510mm H x 175mm D
Item Code Cover Type/Finish
HD-BGW07 Fire proof ABS, 94V-O, PC, PMMA, UV Coated - White
G-Wave 3
Installation must be carried out only by a qualied
electrician
A Type: Power cable equipped
1. Take o and get rid of the closing cover.
2. Separate the power supply cover kit.
3. Secure the line and connect the power cable into the
proper terminal block locations.
4. Verify connections are correct before proceeding.
5. Replace the power supply cover kit.
6. Minimum wire cross section: 2 x 1mm
B Type: Power cable equipped
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
General Safety Information
WARNING
This product is intended for installation by a qualied
service person. Use AWAG No.16 solid conductor for
wiring.
Failure to properly ground unit could result in
electrical shock and/or death.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
All units must be supplied with a 3-wire service. The
ground wire must be connected with the dryers back
plate.
To reduce the risk of re, electric shock and injury please
observe the following.
• Always use genuine spare parts.
• Do not use for purposes other than drying hands.
• Do not place foreign objects in the unit.
• Do not cover the unit.
• Do not use in locations where salt water damage
may occur or where corrosives are present.
• Do not operate in an explosive atmosphere.
• Do not use in areas with high humidity and avoid
condensation on the product.
• Children should be supervised when using the
appliance.
• For indoor use only, not suitable for use outside.
• Keep away from excessive water.
• Unplug appliance before cleaning or maintaining
the appliance.
This appliance must not be disposed together with
the domestic waste.This appliance has to be disposed
at an authorised place for recycling of electrical
devices.
Installation
NOTE: Do not install dryer over wash basin.
If the power supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similar
qualied person in order to avoid a hazard.
Means for disconnection must be incorporated in the
xed wiring in accordance with the wiring rules.
Closing cove
Closing cover
Po
Po
wer supply cover kit
wer supply cover kit
G-Wave
4
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Recommended Mounting Heights
Operation
• No touch operation.
• Shake excess water from hands.
• Place hands under the outlet to start operation.
• Slowly move hands back and forth through the air jet
for about 10 seconds.
• Stops automatically after hands are removed.
Men’s Ladies Children, ages 11-17 Children, ages 3-10 Disabled
33” 31” 29” 23.5” 25”
85 cm 80 cm 75 cm 60 cm 65 cm
From oor to bottom of dryer.
Consumables
Product Order Code
Antibacterial HEPA lter HDS-GW-HEPA-FILTER
Moisturising Gel HDC-G-Wave GELS
Biodrier Anti Bacterial HEPA Filter
The Anti Bacterial Filter is tted to ensure dust and
airborne bacteria is restricted from entering the internal
components and airow of the dryer. The lter should
be replaced after 50,000 uses. This will be indicated by a
ashing red light on the front of the unit.
Biodrier Gels
Biodrier Gels are manufactured exclusively for Biodrier
and preforms 3 jobs in one:
1. Moisturise the hands.
2. Sanitise the product internally and the users hands.
3. Fragrances the surrounding washroom area whilst in use.
The Gels are manufactured from natural sources and are
chemical free.
Filter
Filter Case
G-Wave 5
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
• Green light on: Standby, dryer ready for use
• Changing light colours: Operating
• Flashing blue light: Water tank full alert
• Flashing red light: Filter change alert
When a new lter has been installed correctly the
LED light will ash twice after ve secconds. If the
light does not ash then the lter needs to be re
installed correctly.
• Red light and blue light ash alternately: Water
tank full and change lter alert
LED Display
LED Display
Power Settings
Change the speed
from high to low
Power Switch
G-Wave
6
General Maintenance
All surfaces of the unit should be cleaned daily with a
soft cloth dampened with warm, soapy water. Polish
with a soft dry cloth.
Regularly check the LED display to see the status of the
lter condition and water tank level.
DO NOT use caustic solutions or abrasive cleaning mate-
rials on the drier.
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
If the LED light on the front of the unit ashes blue then
the water tank needs to be emptied.
The water tank should be cleaned and emptied regu-
larly to prevent bacteria growth and unwanted smells.
If the water tank is not emptied promptly the water can
overow and may interfere with the machine and cause
a slipping hazard on the oor.
Always use the unit with a genuine lter and the water
tank in place.
Water Tank Maintenance
Anti-theft bolt
Lock: Right
Unlock: Left
Water tank
G-Wave 7
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Anti-theft bolt
Lock: Right
Unlock: Left
HEPA FIlter
If the LED light on the front of the unit ashes red then
the HEPA lter needs to be changed. The HEPA lters last
for 50,000 uses.
To change the lter slide the anti theft lock to left and
remove the lter case from the underside of the unit.
Remove the old HEPA lter from the case and replace
with a new one.
When a new lter has been correctly installed the LED
light will ash twice after ve secconds. If the light does
not ash then the lter needs to be re-installed cor-
rectly.
Warning – if the lter is not replaced in time, it may
interrupt air ow and overheat the motor. In this case,
the warranty will be invalidated.
The lter must be replaced every 3-6 months to avoid
invalidating the warranty period.
Always use the unit with a genuine lter and the water
tank in place.
Do not attempt to wash and re-use the HEPA lter. The
lter works for 50,000 uses, after this it should be dis-
posed of and replaced by another lter.
Do not install the lter cartridge if the lter is wet or
damp, it must be perfectly dry. If the cartridge is in-
stalled wet it can cause serious motor damage and the
warranty will be invalidated.
Gel Blocks
The gel block is situated in the underside of the lter
case. The gel block should be replaced every month,
each pack contains 12 blocks.
Changing The Filter and Gel Block
Gel block
HEPA Filter
To order Gel Blocks and HEPA Filters please contact us:
call: 01404 814292
email: sales@biodrier.com
or visit: www.dripdropdry.com
Product Order Code
Antibacterial HEPA lter HDS-GW-HEPA-FILTER
Moisturising Gel HDC-G-Wave GELS
G-Wave
8
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Diagram
G-Wave 9
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Parts List
Key Description
1Front panel
2Front decorating ring
3Front panel bracket
4Front cover
5Motor upper cover
6Rubber mounting grommet
7Motor
8Airproof sheath
9Motor cushion ring
10 Connection
11 Cover motor lower
12 Transformer
13 Main cover
14 Spring
15 Air valve brush
16 Power cord cover airproof ring
17 Connection
18 Power cord cover
19 Back panel
20 Power cord closing cover
21 Wall bracket
22 Air valve cover
23 Valve inner
24 Filter sponge
25 Filter bracket
26 Switch A
27 Switch B
28 Heat sink
Key Description
29 Main board
30 PCB cover
31 Power switch
32 Speed control switch
33 Silica gel
34 Switch holder
35 Switch waterproof cover
36 Cover
37 Sensor upper cover
38 Sensor board
39 Sensor holder A
40 Bottom cover
41 Display panel
42 LED cover
43 Sensor lower cover
44 Sensor holder B
45 Water tank cover
46 Water tank
47 Connector panel
48 Pole
49 Air freshener
50 Pole support sheet
51 Theft panel
52 Theft panel cover
53 Power cord protection cover
54 Screen lter
G-Wave
10
Important Safety Instructions
Warning – to reduce the risk of re, electric shock or
injury to persons please observe the following:
• Use this unit only in the manner intended by the
manufacturer. The manufacturer is not responsible
for damages caused by misuse or defective installa-
tion.
• The instructions contained within the installation
template enclosed must be followed carefully when
installing the unit. Failure to accurately follow the
instructions may result in the incorrect operation
of this unit, damage to property and/or personal in-
jury.
• Installation work and electrical wiring must be done
by qualied personnel in accordance with all ap-
plicable codes and standards, including re related
construction.
• When cutting or drilling into a wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• This unit must be powered by a dedicated circuit
breaker with the appropriate rating. Circuit cable
must t current consumption for this unit.
• This unit has been designed for indoor use only, pro-
tected from water, sun and extreme temperatures.
Do not use outdoors or close to moisture and heat
generators.
• This unit can only be revised, maintained , repaired
and removed by qualied personnel. If the unit stops
and works strangely, contact your regional dealer or
contractor.
• This appliance can be used by children over 8 years
and above and persons with reduced physical, sen-
sory or mental capabilities or lack of experience and
knowledge if they have been given supervision and/
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
• Children should not play with the appliance.
• Cleaning and maintenance should be carried out by
a competent adult.
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly quali-
ed personnel in order to avoid hazard.
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
G-Wave 11
Installation Template
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
FW3 LTD, Biodrier
Unit 3, Woodlands Business Park, Burlescombe, Devon, EX16 7LL
tel: +44(0)1823 672 970 • email: sales@biodrier.com
Table of contents
Other Biodrier Dryer manuals
