BIOS Icarus Li2 User manual

bioslighting.com
[phone]
[e-mail] Page 1 of 2
Rev1 [2021 01/05]
Specications and dimensions subject to change without notice.
Contact BIOS for questions and the most current information.
ICES-005 (A)
Installation Guide
Icarus™Li2
HIGH OUTPUT
INSTALL IN SECONDS
ENERGY EFFICIENT
1. Loosen RapidRack™thumb screw enough to slide RapidRack™ plate.
2. Slide RapidRack™plate into desired rack mount position.
3. Tighten RapidRack™thumb screw to secure RapidRack™plate into place.
RapidRack™ Mounting Plate
RapidRack™ Thumb Screw
Extend & rest on ledge
Extend & secure
1. Extend RapidRack™ plates on one end and rest on rack
ledge.
2. Extend RapidRack™ on opposite side to complete
secure mounting solution.
Tip:
For more info, documents and videos reqarding your BIOS Icarus LLi xtures: Please log onto www.bioslighting.com/product/icarus-lli/
1. Simply slide joiner plate into each side of the xture.
2. Use thumb screws to screw joiner plate into place.
Li 2 Joiner Plate
1. Utilize brackets to mount power supply and cables.
2. Snap brackets into place on the middle two bars.
3. Screw power supply into brackets.
Brackets for cables and PSU box
Screw joiner plate into place
For PSU wiring info, please visit product page by scanning QR code.
IMPORTANT:
To avoid risk of damage to the xture and their LEDs, make all wiring
Easy Rack Mount Solution with RapidRack™
BP-0Li2-000-KTL013-x & BP-0Li2-000-KTH013-X
Read all instructions prior to performing installation. All facility wiring to be performed only by licensed electricians in accordance with National Electric Code
and local code specications. Failure to do so voids warranty and may result in serious injury or death. Supplied Connectors on all power cables have breaking
capacity and can be installed by non-licensed individuals. Disconnect main power prior to installation, maintenance or service.
ELECTRICAL SHOCK HAZARD CAUTION!
Joining Your Li2 Fixture
On-Board Power Supply

bioslighting.com
[phone]
[e-mail] Page 2 of 2
Rev1 [2021 01/05]
Specications and dimensions subject to change without notice.
Contact BIOS for questions and the most current information.
ICES-005 (A)
BIOS Icarus™Li2
Installation Guide
Main Cable Adjustment
1. Insert cable through top opening of cable gripper.
2. Excess feed will depart cable gripper via the side exit hole.
3. Cable gripper will auto lock cable feed in place.
4. Pressing top plunger will relieve load from cable.
Insert cable here
Side exit hole
Safety nut
Adjusting Fixture Height
1. Unscrew safety nut.
2. Feed desired/measured amount of cable through cable gripper.
3. To retract cable, press plunger to release load and back feed cable.
4. Release plunger and cable gripper locks cable in place.
5. Tighten safety nut to complete the installation.
WARNING: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. Any changes or modications not expressly
approved by the manufacturer could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
These photobiological safety markings are based on testing of the light output characteristic of a single horticultural luminaire. Increased exposure
risk to facility personnel may be present depending upon the number of horticultural luminaires and their placement and/or positioning within the
plant growth facility. It is the responsibility of the plant growth facility to address these risks at the facility level and to ensure that people entering
the plant growth areas while the lights are on, are aware of these risks and that appropriate safeguards are in place.
To provide proper heat ventilation, LED light bars and heat sinks should maintain at least a 4” distance from all other objects.
For lighting equipment with cords or wiring harnesses, instructions shall include information to guide the installation such that cords:
• Are not concealed or extended through a wall, oor, ceiling, or other parts of the building structure;
• Are not located above a suspended ceiling or dropped ceiling;
• Are not permanently axed to the building structure;
• Are routed so that they are not subject to strain and are protected from physical damage;
• Are visible over their entire length; and
• Are used within their rated ampacity as determined for the maximum temperature of the installed environment specied in the instructions.
Bios provides a 5 year limited warranty on the Icarus product against defects in materials and workmanship under normal use conditions. Eective warranty
begins on the date of the invoice or purchase receipt. This xture meets UL8800 - a standard specic to LED lighting xtures and is approved for use in both
the US & Canada. Full warranty information can be found at www.bioslighting.com.
Warranty Information (abridged)
For general cleaning of external parts of the Icarus™LLi xture and spot-free lens cleaning use only facility compressed air or a soft, non-abrasive cloth and
and water. If necessary, a mild general purpose non-solvent glass cleaner that is compatible with indoor crop production regulations may be used.
Product Maintenance:
FCC responsible party name: BIOS Lighting - Address: 2796 Loker Ave W Suite 111 Carlsbad, CA. 92010 - 321-260-2467
Cable Suspension Mounting
Product Info
• Suitable for operating environment ranging from -20℃ to 40℃(-4°F to 104°F).
• Suitable for wet locations and IP65.
• Driver lifetime:≥50000H .
• Dimming:0-10V.