Biostar BIELK-PAT User manual

FCC Informaon and Copyright
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instrucon
manual, may cause harmful interference to radio communicaons. Operaon of this equipment in a
residenal area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
The vendor makes no representaons or warranes with respect to the contents here and specially disclaims
any implied warranes of merchantability or tness for any purpose. Further the vendor reserves the right
to revise this publicaon and to make changes to the contents here without obligaon to nofy any party
beforehand.
Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the vendor’s approval
in wring.
The content of this user’s manual is subject to be changed without noce and we will not be responsible for
any mistakes found in this user’s manual. All the brand and product names are trademarks of their respecve
companies.
Dichiarazione di conformità sinteca
Ai sensi dell’art. 2 comma 3 del D.M. 275 del
30/10/2002
Si dichiara che questo prodoo è conforme
alle normave vigen e soddisfa i requisi
essenziali richies dalle direve
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaraon of conformity
We declare this product is complying with the
laws in force and meeng all the essenal
requirements as specied by the direcves
2004/108/CE, 2006/95/CE and 1999/05/CE
whenever these laws may be applied

2 | Table Of Contents
Table Of Contents
FCC Informaon and Copyright ������������������������������������������������������������������������������� 1
Chapter 1: Introducon������������������������������������������������������������������������������������������� 3
1.1 Before You Start .....................................................................................................................................3
1.2 Specicaons .........................................................................................................................................4
1.3 Rear Panel Connectors...........................................................................................................................6
1.4 Motherboard Layout..............................................................................................................................7
Chapter 2: Hardware installaon����������������������������������������������������������������������������� 9
2.1 Central Processing Unit (CPU)................................................................................................................9
2.2 Fan Headers ...........................................................................................................................................9
2.3 Installing System Memory......................................................................................................................9
2.4 Expansion Slots ....................................................................................................................................10
2.5 Headers / Connectors ..........................................................................................................................11
2.6 Jumpers / Slot ......................................................................................................................................16

Chapter 1: Introducon | 3
BIELK-PAT User’s Manual
Chapter 1: Introducon
1.1 Before You Start
Thank you for choosing our product. Before you start installing the motherboard, please make sure you
follow the instrucons below:
• Prepare a dry and stable working environment with sucient lighng.
• Always disconnect the computer from power outlet before operaon.
• Before you take the motherboard out from an-stac bag, ground yourself properly by touching
any safely grounded appliance, or use grounded wrist strap to remove the stac charge.
• Avoid touching the components on motherboard or the rear side of the board unless necessary.
Hold the board on the edge, do not try to bend or ex the board.
• Do not leave any unfastened small parts inside the case aer installaon. Loose parts will cause
short circuits which may damage the equipment.
• Keep the computer from dangerous area, such as heat source, humid air and water.
• The operang temperatures of the computer should be 0 to 60 degrees Celsius.
• To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
Note
»
»The package contents may be dierent due to the sales region or models in which it was sold. For more
informaon about the standard package in your region, please contact your dealer or sales representave.

4 | Chapter 1: Introducon
1.2 Specifications
Dimensions 148 x 102 x 1.6 mm
Processor Intel® Celeron® Processor J6412/X6413E, TDP 10W (Wide range temperature: X6413E)
Chipsets
EDP to LVDS : CH7513A-BFI
DDI to VGA (No support wide range temperature): RTL2166
LAN controller: I226V colay I226-IT (I226-IT for wide range temperature.)
Audio Codec (No support wide range temperature): ALC897
Audio Amplier(No support wide range temperature): ALC105
Super IO: IT8786
System Memory 2 x 260-pin socket support DDR4 3200MHz SO-DIMM, up to 32 GB
Graphic
Intel® Integrated Graphics
HDMI 1. 1 x HDMI connector
2. Support HDMI2.0
VGA
(No support wide range temperature)
DDI to VGA: RTL2166
1 x VGA connector
LVDS/eDP
1. Chipset: CH7513A-BFI
2. Support LVDS 18/24bit dual channels
3. Support eDP two channel
4. 1 x 2*15 wafer box pin-header for LVDS connector
(eDP and LVDS share with the same connector)
5. eDP and LVDS switch mode by BIOS seng
Ethernet
Support 2 x GbE LAN:
(1) 2 x Intel I225V colay I225-IT 2.5G LAN, RJ45 connector. (I225-IT for wide range temperature)
(2) 1 x 2*4-Pin 2.0-pitch wafer box pin-header for front LAN LED
SATA
Support 2 x SATA3
(1) 1 x SATAIII7pin connector with 1 x 1*4-pin Power connector for HDD (Support 5V and 12V)
(2) 1 x SATA3 for M.2 M Key, support PCIe x2 NVMe storage.
Universal Serial Bus
& PCIe
USB3.1 Gen1
(1) 2 x USB3.1 for 1x dual-stack I/O connectors
(2) 1 x USB3.1 for M.2 B key ,Integrate SIM Card slot
(3) 1 x 1*3-pin pin-header for select Rear USB3.0 Power w/ 5V/5VSB
(5VSB support wake on USB funcon)
USB2.0 Gen1
(1) 2 x USB2.0 for 1 x dual-stack I/O connectors.
(2) 1 x USB 2.0 for Mini-PCIe
(3) 2 x USB2.0 for 1 x 2*5pin header
(4) USB2.0 voltage support 5V only.
Super IO Controller : IT8786
Support 4 x COM Port, DIO,
Serial Port
Support 4 x COM port, dene as below,
2 x RS232/422/485 (COM1/2)
(1) 2*5 pin header
(2) Mode selecon by BIOS control.
(3) Support Auto ow control.
(4) 2 x 1*3 PIN header support 0/5/12V by jump selecon, default 0V.
2 x RS232 (COM3-4)
(1) 2 x 2*5 Header
Expansion Slot
(1) 1 x M.2 key B 3042/3052 slot with SIM card connector, support PCIe and USB3.0 interface.
(2) 1 x Full Size Mini-PCIe, support USB2.0 and PCIe interface.
(3) 1 x M.2 Key-M Slot, support PCIe x 2 NVMe storage.
Audio
(No support wide range
temperature)
Audio Codec: ALC897+ ALC105
(1) Support 1 x 2*4pin Audio header, support Line-out/MIC/Line-in.
(2) 1 x 1*4pin 2.0-pitch speaker header, support 2 x 2W speaker.
Digital I/O 1 x 2*5-pin 2.0-pitch header, support 8-Bit GPIO.
Front Panel 1 x 2*5-pin 2.0-pitch Front panel header
Indicator 1 x Power LED for motherboard Power-on display

Chapter 1: Introducon | 5
BIELK-PAT User’s Manual
Buzzer
(No support wide range
temperature)
1 x Buzzer
Power Input DC-IN 9 ~ 24V , 2pin phoenix connector.
Edge IO
1 x HDMI connector
1 x Dual-Stack USB3.0 connectors
1 x Dual-Stack USB2.0 connectors
2 x RJ45 connectors, support 2.5G GbE.
1 x VGA connector
Onboard pin-header
Expansion slots
1 x M.2 key B slot, with SIM Card slot
1 x Full size Mini-PCIe
1 x M.2 Key-M Slot
SATA
1 x SATA3 7pin connector with 1 x 1*4-pin Power connector for SATA power
(support 5V and 12V power switch)
Display
1 x 2*15 wafer box pin-header for LVDS connector
1 x 1*3-pin 2.0-pitch wafer box pin-header for 3.3V/5V for LCD power select jumper
1 x 1*6-pin 2.0-pitch connector for LCD Backlight Inverter
1 x 1*3-pin 2.0-pitch wafer box pin-header for 5V/12V for LCD Backlight Inverter
Audio
1 x 1*4-pin 2.0-pitch wafer box pin-header for 2x 2W speaker
1 x 2*4pin 2.0-pitch wafer box pin-header for Line-out/MIC/Line-in
1 x Buzzer
USB
1 x 2*5-pin 2.0-pitch wafer box pin-header, support 2x USB2.0
1 x 1*3-pin pin-header for select Rear USB3.0 Power w 5V/5VSB
Power
1 x 1*2-pin Phoenix-type power connector for DC-in 9 ~ 24V
Serial Port
2 x 2*5 Header for RS232/422/485 (COM1/2)
2 x 2*5 Header for RS232 (COM2/3)
2 x 1*3-pin 2.0-pitch wafer box pin-header for COM1/2 Serial Port Power Select Jumper (Select 0/5/12V)
Others
1 x 2*5-pin 2.0-pitch GPIO header (4*GPI, 4*GPO)
1 x 1*3 pins, support 5V/3.3V header for 5V/3.3V GPIO switch
1 x 3-pin 2.0-pitch pin-header for Clear CMOS Jumper
1 x 1*3-pin 2.0-pitch pin-header for select AT/ATX mode
1 x 2*5-pin 2.0-pitch wafer box pin-header for Front panel.
1 x 1*2-pin 1.0-pitch connector for Baery (cable Length 130mm)
1 x Power LED for motherboard Power-on display
1 x 1*3-pin Wafer connector Smart DC FAN for system
O.S. support Windows 10 IoT Enterprise 2019 1809 64-bit
Linux Ubuntu 20.04
BIOS Support UEFI only
ESD/ EMI Contact with 4Kv, Air with 8Kv.
EMI class A
Operaon Temp. -40ºC ~ 85ºC (Wide range temperature) Humidity : 10% ~ 90% (X6413E CPU)
0ºC ~ 60ºC Humidity : 10% ~ 90% (J6412 CPU)
Storage Temp. -40ºC ~ 85ºC Humidity : 10% ~ 90%

6 | Chapter 1: Introducon
1.3 Rear Panel Connectors

Chapter 1: Introducon | 7
BIELK-PAT User’s Manual
1.4 Motherboard Layout
Top View

8 | Chapter 1: Introducon
Back View
»
» represents the 1st pin.

Chapter 2: Hardware installaon | 9
BIELK-PAT User’s Manual
Chapter 2: Hardware installaon
2.1 Central Processing Unit (CPU)
The mainboard includes an Intel® Celeron processor, and a cooler has been installed to provide sucient
cooling
2.2 Fan Headers
These fan headers support cooling-fans built in the computer. The fan cable and connector may be
dierent according to the fan manufacturer. Connect the fan cable to the connector while matching the
black wire to pin#1.
CPU_FAN: CPU Fan Header
Pin Assignment
1VCC12
2 GND
3 CPU_FAN_TACH
2.3 Installing System Memory
DIMM1: DDR4L Memory Module (260pin SO-DIMM)
Note
»
»If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
1. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
2. Insert the DIMM rmly into the slot unl the retaining clips snap back in place and the DIMM is properly
seated.

10 | Chapter 2: Hardware installaon
Memory Capacity
DIMM Socket Locaon DDR4L Module Total Memory Size
DIMM1 4GB/8GB/16GB/32GB Max is 32GB
2.4 Expansion Slots
M2_1: M.2 (Key M) Slot
NGFF CONN H8.5XL80MM KEY M
• The M.2 slot supports M.2 Type 2242 module. When installing M.2 module, please place the screw
and hex pillar to correct posion.
Pin Assignment Assignment Pin Pin Assignment Assignment Pin
1GND +V3.3S 2 37 PCIE_TX7_DP NC 38
3 GND +V3.3S 4 39 GND NC 40
5NC NC 6 41 SELOUT1_RXN NC 42
7 NC NC 8 43 SELOUT1_RXP NC 44
9 GND M2_DAS 10 45 GND NC 46
11 NC +V3.3S 12 47 SELOUT1_TXN NC 48
13 NC +V3.3S 14 49 SELOUT1_TXP PCIRST1_N 50
15 GND +V3.3S 16 51 GND PCIE_CLKREQ2_N 52
17 NC +V3.3S 18 53 PCIE_REFCLK2_DN WAKE_N 54
19 NC NC 20 55 PCIE_REFCLK2_DP NC 56
21 GND NC 22 57 GND NC 58
23 NC NC 24
25 NC NC 26
27 GND NC 28 67 NC NC 68
29 PCIE_RX7_DN NC 30 69 NC +V3.3S 70
31 PCIE_RX7_DP NC 32 71 GND +V3.3S 72
33 GND NC 34 73 GND +V3.3S 74
35 PCIE_TX7_DN NC 36 75 GND

Chapter 2: Hardware installaon | 11
BIELK-PAT User’s Manual
2.5 Headers / Connectors
F_USB1: WAFER 2X5 2MM N9-S
Pin Assignment
1VCC5
2 VCC5
3 HUB2_USBN4
4 HUB2_USBN5
5HUB2_USBP4
6 HUB2_USBP5
7 GND
8 GND
9 DUMMY PIN
10 NC
JW_FP: WAFER 2X5 2MM N10-S AIH
Pin Assignment
1HDD_LED+
2 HDD_LED-
3 GND
4 SYS_RST_N
5VCC5
6 POWER_LED+
7 POWER_LED-
8 PWRBTN
9 GND
10 NC
F_AUDIO1: HEADER 2X4 N6
Pin Assignment
1MIC1_L2
2 GND
3 MIC1_R2
4 VCC3.3
5LINEOUT_R2
6 DUMMY
7 LINEOUT_L2
8 GND

12 | Chapter 2: Hardware installaon
JSPK1: BOX 1X4 2mm-AIH-1
Pin Assignment
1SPKLN
2 SPKLP
3 SPKRP
4 SPKRN
INVERTER: WAFER 1X6 2mm W-AIH-1
Pin Assignment
1VCC_BL
2 VCC_BL
3 ENABKL_
4 LBKLT_CTL
5GND
6 GND

Chapter 2: Hardware installaon | 13
BIELK-PAT User’s Manual
LVDS/EDP: SMD WAFER 2X15 1.25MM-AIH-1
Pin Assignment
1LVDSB_DATA3_N
2 LVDSB_DATA3_P
3 LVDSB_CLK_N
4 LVDSB_CLK_P
5LVDSB_DATA2_N
6 LVDSB_DATA2_P
7 LVDSB_DATA1_N
8 LVDSB_DATA1_P
9 LVDSB_DATA0_N
10 LVDSB_DATA0_P
11 NC
12 NC
13 GND
14 GND
15 GND
16 GND
17 LVDSA_DATA3_P
18 LVDSA_DATA3_N
19 LVDSA_CLK_P
20 LVDSA_CLK_N
21 LVDSA_DATA2_P
22 LVDSA_DATA2_N
23 LVDSA_DATA1_P
24 LVDSA_DATA1_N
25 LVDSA_DATA0_P
26 LVDSA_DATA0_N
27 PVDD2
28 PVDD2
29 PVDD2
30 PVDD2
JDIO: HEADER 2X5 2MM S-AIH
Pin Assignment
1FIFO_DO01
2 FIFO_DI01
3 FIFO_DO02
4 FIFO_DI02
5FIFO_DO03
6 FIFO_DI03
7 FIFO_DO04
8 FIFO_DI04
9 GND
10 VCCDIO

14 | Chapter 2: Hardware installaon
SATAPW: BOX 1X4 2.5MM-AIH-1
Pin Assignment
1VCC5
2 GND
3 GND
4 VCC12
DCIN1: PHOENIX CONN 2P
Pin Assignment
1GND
2 VCC(9V ~ 24V)
JCOM1, JCOM2, JCOM3, JCOM4: WAFER 2X5 2MM N10-S
Pin Assignment
1COM1C_DCD
2 COM1C_RXD
3 COM1C_TXD
4 COM1C_DTR
5GND
6 COM1C_DSR
7 COM1C_RTS
8 COM1C_CTS
9 COM1C_RI
10 NC

Chapter 2: Hardware installaon | 15
BIELK-PAT User’s Manual
Edp(與LVDS/EDP connector共用): SMD WAFER 2X15 1.25MM-AIH-1
Pin Assignment
1NC
2 NC
3 NC
4 NC
5NC
6 NC
7 NC
8 NC
9 NC
10 NC
11 NC
12 NC
13 NC
14 NC
15 NC
16 NC
17 NC
18 NC
19 eDP_AUXP
20 eDP_AUXN
21 eDP_TX0P
22 eDP_TX0N
23 eDP_TX1P
24 eDP_TX1N
25 EDP_HPD
26 NC
27 PVDD2
28 PVDD2
29 PVDD2
30 PVDD2
JSPI: HEADER 2X5 2MM N10 S-AIH
Pin Assignment
1NC
2 SPI_WP_N
3 VCC3.3
4 GND
5SPI_CS0_N_R
6 SPI_CLK_R
7 SPI_MISO_R
8 SPI_MOSI_R
9 SPI_HD
10 DUMMY

16 | Chapter 2: Hardware installaon
2.6 Jumpers / Slot
Jumper Seng
The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”,
if not, that means the jumper is “open”.
Pin opened Pin closed Pin 1-2 closed
JCMOS: Clear CMOS Jumper
Placing the jumper on pin2-3 allows user to restore the BIOS safe seng and the CMOS data. Please
carefully follow the procedures to avoid damaging the motherboard.
Pin 1-2 Close: Normal Operaon (Default)
Pin 2-3 Close: Clear CMOS data
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for ve seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.

Chapter 2: Hardware installaon | 17
BIELK-PAT User’s Manual
JLV1
JLV1
VCC5 JLV1(1-2)
VCC3_3 JLV1(2-3) (Default)
JLV2
JLV2
VCC12 JLV2(1-2) (Default)
VCC5 JLV2(2-3)
JPUSB1
JPUSB1
VCC5 JPUSB1(2-3) (Default)
VCC5A JPUSB1(1-2)

18 | Chapter 2: Hardware installaon
JPDIO1
JPDIO1
VCC5 JPDIO1(1-2) (Default)
VCC3_3 JPDIO1(2-3)
JPOWER1
JPOWER1
ATX JPOWER1(1-2) (Default)
AT JPOWER1(2-3)
COMPWR
COMPWR
VCC12 COMPWR(1-2)
VCC5 COMPWR(2-3)

Chapter 2: Hardware installaon | 19
BIELK-PAT User’s Manual
COMPWR1
COMPWR1
VCC12 JLV1(1-2)
VCC5 JLV1(2-3)
SATA1: SATA CONNECTOR-B
Pin Assignment
1GND
2 SSATA_TXP1
3 SSATA_TXN1
4 GND
5SSATA_RXN1
6 SSATA_RXP1
7 GND
SCAN1: NANO SIM 6P Li
Pin Assignment
C1 SIM_PWR_B
C2 UIM_RESET
C3 UIM_CLK
C5 GND
C6 SIM_VPP
C7 UIM_DATA

20 | Chapter 2: Hardware installaon
SCAN2: M.2 H4.8MM KEY B
Pin Assignment Assignment Pin
1M2_B_CFG3 +V3.3A 2
3 GND +V3.3A 4
5GND FULL_CARD_PWROFF 6
7 USB2_P3_DP NC 8
9 USB2_P3_DN NC 10
11 GND
21 M2_B_CFG0 NC 20
23 NC NC 22
25 NC NC 24
27 GND NC 26
29 USB3_P3_RX_DN NC 28
31 USB3_P3_RX_DP UIM_RESET 30
33 GND UIM_CLK 32
35 USB3_P3_TX_DN UIM_DATA 34
37 USB3_P3_TX_DP SIM_PWR_B 36
39 GND M2_B_DEVSLP 38
41 PCIE_RX2_DN NC 40
43 PCIE_RX2_DP NC 42
45 GND NC 44
47 PCIE_TX2_DN NC 46
49 PCIE_TX2_DP NC 48
51 GND PLTRST_N 50
53 PCIE_REFCLK1_DN PCIE_CLKREQ1_N 52
55 PCIE_REFCLK1_DP WAKE_N 54
57 GND NC 56
59 NC NC 58
61 NC NC 60
63 NC NC 62
65 NC NC 64
67 M2_WWAN_RST_N SIM_DET 66
69 M2_B_CFG1 SUSCLK_M2B 68
71 GND +V3.3A 70
73 GND +V3.3A 72
75 M2_B_CFG2 +V3.3A 74