Biostar P4 TSV Operating and installation instructions

P
P
P4
4
4T
T
TS
S
SV
V
V
i
FCC I
FCC IFCC I
FCC In
nn
nformation
formationformation
formation and Copyright
and Copyrightand Copyright
and Copyright
This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in
a particular installation.
The vendor makes no representations or warranties with respect to the
contents here of and specially disclaims any implied warranties of
merchantability or fitness for any purpose. Further the vendor reserves
the right to revise this publication and to make changes to the contents
here of without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without
first obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice
and we will not be responsible for any mistakes found in this user’s
manual. All the brand and product names are trademarks of their
respective companies.

C
C
Co
o
on
n
nt
t
te
e
en
n
nt
t
t
ii
LAYOUT OF P4TSV.................................................................................1
COMPONENT INDEX.............................................................................2
ENGLISH...................................................................................................3
P4TSV Features ......................................................................................................... 3
Package contents......................................................................................................5
How to set up Jumper............................................................................................... 5
CPU Installation ......................................................................................................... 5
DDR DIMM Modules: DDRA1-2, DDRB1-2................................................................ 6
Installing DDR Module............................................................................................... 7
Jumpers, Headers, Connectors & Slots................................................................... 7
ESPAÑOL.................................................................................................14
Características del P4TSV ......................................................................................14
Contenido del Paquete............................................................................................ 16
Cómo instalar un Puente......................................................................................... 16
Instalación del CPU ................................................................................................. 16
Módulos DDR DIMM: DDRA1-2, DDRB1-2 ............................................................. 17
Instalación del Módulo DDR ................................................................................... 18
Puentes, Cabezales, Conectores y Ranuras ......................................................... 19
DEUTSCH................................................................................................26
Spezifikationen von P4TSV..................................................................................... 26
Verpackungsinhalt................................................................................................... 28
Einstellung der Jumper........................................................................................... 28
Installation der CPU................................................................................................. 28
DDR DIMM Modules: DDRA1-2, DDRB1-2.............................................................. 29
Installation von DDR-Modul....................................................................................30
Jumpers, Headers, Anschlüsse & Slots ................................................................30
WARPSPEEDER.....................................................................................37
Introduction.............................................................................................................. 37
System Requirement............................................................................................... 37
Installation................................................................................................................ 38
Usage........................................................................................................................ 39
TROUBLE SHOOTING.........................................................................47
SOLUCIÓN DE PROBLEMAS.............................................................48
PROBLEMLÖSUNG..............................................................................49

1
Layout of P4TSV
NOTE: ●represents the first pin.

2
Component Index
A. Back Panel Connectors O. JCL1: Case Open Connector
B. JAUDIO1: Front Audio Header P. JCMOS: Clear CMOS Jumper
C. JCDIN1: CD-Rom Audio-In Header Q. SATA1-2: Serial ATA Connectors
D. JGAME1: Game Header R. IDE1-2: Hard Disk Connectors
E. JCDIN2: CD-ROM Audio-In Header S. FDD1: Floppy Disk Connector
F. CNR1: Communication Network
Riser Slot T. JATXPWR1: ATX Power Connector
G. PCI1-3: Peripheral Component
Interconnect Slots U. DDRA1-2/ DDRB1-2: DDR DIMM Modules
H. JSPDIF_OUT1: Digital Audio
Connector V. JCFAN: CPU Fan Connector
I. JWOL1: Wake On LAN Header W. JATXPWR2: ATX Power
Connector
J. JSFAN1: System Fan Header X.
A
GP1: Accelerated Graphics Port
Slot
K. JUSBV3_4: 5V/5VSB Selection for
JUSBV2/3 Y. JUSBV2: 5V/5VSB Selection for JRJ45USB1
L. JUSB2/3: Front USB Headers Z. JKBV1: 5
V
/5VSB Selection for
Keyboard
M. JDJ1: Audio DJ Connector A1. JUSBV1: 5V/5VSB Selection for
JUSB1
N. JPANEL1 : Front Panel Connector

3
English
P4TSV Features
A. Hardware
CPU
Provides Socket-478.
Supports the Intel Pentium 4 processor up to 3.06GHz.
Front Side Bus at 400/533/800MHz.
Supports Hyper-Threading.
Supports Northwood and Prescott CPU. (Willamette not supported)
Chipset
North Bridge: Intel 865G.
South Bridge: Intel ICH5.
Main Memory
Supports one or two 64-bit wide DDR data channels with 1 or 2 DIMMs
per-channel.
Available bandwidth up to 3.2GB/s(DDR400) for single-channel mode and 6.4GB/s
(DDR 400) in dual channel mode.
Supports 128-MB, 256-Mb, 512-Mb and 1-GB DDR technologies.
Supports only x8, x16 DDR devices.( Does not support registered DIMMs or
double sided X 16 DIMMs)
Supports four bank devices.
Maximum memory size is 4GB.
Super I/O
Chip: ITE IT8712F.
Low Pin Count Interface.
Provides the most commonly used legacy Super I/O functionality.
Environment Control initiatives,
- H/W Monitor
- Fan Speed Controller
- ITE's "Smart Guardian" function
Slots
Three 32-bit PCI bus master slots.
One CNR slot.
One AGP 4X/8X slot.
On Board IDE
Supports four IDE disk drives.
Supports PIO Mode 5, Bride Mode and Ultra DMA 33/66/100 Bus Master Mode.
Supports 2 Serial ATA (SATA) ports.

4
- Compliant with SATA 1.0 specification
- Data transfer rates up to 1.5 GB/s
LAN
Chip: RTL8100B.
Supports 10 Mb/s and 100 Mb/s auto-negotiation.
Half/Full duplex capability.
Supports ACPI power management.
On Board AC’97 Sound Codec
Chip: CMI9739A.
Compliant with AC’97 specification.
AC97 2.2 interface.
Supports 6 channels.
On Board Peripherals
a. Rear side
1 serial port.
1 parallel port. (SPP/EPP/ECP mode)
1 VGA port.
Audio ports in vertical.
1 RJ-45 LAN jack.
Supports PS/2 mouse and PS/2 keyboard.
4 USB2.0 ports.
b. Front Side
1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes.
4 USB2.0 ports.
Dimensions
Micro ATX Form Factor: 24.4 X24.4cm (W X L)
B. BIOS & Software
BIOS
Award legal BIOS.
Supports APM1.2.
Supports ACPI.
Supports USB Function.
Software
Supports Warpspeeder™, 9th Touch™, FLASHER™, StudioFun! ™ (optional).
Offers the highest performance for Windows 98 SE, Windows 2000, Windows Me,
Windows XP, SCO UNIX etc.

5
Package contents
HDD Cable X 2
FDD Cable X1
User’s Manual X1
Fully Setup Driver CD X1
StudioFun! Application CD X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF Cable X 1 (optional)
Rear I/O Panel for Micro ATX Case X1 (optional)
Serial ATA Cable X1
Serial ATA Power Switch Cable X1
How to set up Jumper
The illustration shows to how set up jumper. When the Jumper cap is placed on pins, the
jumper is “close”. IF no jumper cap is placed on the pins, the jumper is ”open”. The
illustration shows a 3-pin jumper whose pin1and 2 are “close” when jumper cap is placed
on these 2 pins.
Jumper open Jumper close Pin1-2 close
CPU Installation
Step1
Step1Step1
Step1:
::
: Pull the lever sideways away from the socket and then raise the lever up to a
90-degree angle.
Step2
Step2Step2
Step2:
::
:Look for the white dot/cut edge. The white dot/cut edge should point wards the
lever pivot. The CPU will fit only in the correct orientation.
Step3:
Step3:Step3:
Step3: Hold the CPU down firmly, and then close the lever to complete the installation.
Step4:
Step4:Step4:
Step4: Put the CPU Fan on the CPU and buckle it. Connect the CPU fan power cable to
the JCFAN1. This completes the installation.

6
Step1 Step2 Step3 Step4
Step1 Step2 Step3 Step4Step1 Step2 Step3 Step4
Step1 Step2 Step3 Step4
CPU Fan Headers: JCFAN1
Pin Assignment
1 Ground
2 +12V
1
JCFAN1 3 FAN RPM Sense
System Fan Headers: JSFAN1
Pin Assignment
1 Ground
2 +12V
1
JSFAN1
3 FAN RPM Sense
DDR DIMM Modules: DDRA1-2, DDRB1-2
Supports up to four DDR DIMMs(two DIMMs per channel), single-sided and/ or
double-sides.
For Dual Channel Operation, DIMMs must be populated in identical pairs. It
has to be the combination of DDRA1+DDRB1 (Blue DIMMs) or DDRA2+DDRB2
(white DIMMs). For more dual channel operation information please log on:
www.biostar.com.tw)
DRAM Access Time: 2.5V Unbuffered/ no registered (without ECC) DDR SDRAM
PC2100/ PC2700/ PC3200 Type required.
DRAM Type: 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin)

7
Total Memory Size with Unbuffered/ Registered DIMMs
DIMM Socket
Location DDR Module Total Memory Size (MB)
DDRA1 64MB/128MB/256MB/512MB/1GB
*1
DDRA2 64MB/128MB/256MB/512MB/1GB
*1
DDRB1 64MB/128MB/256MB/512MB/1GB
*1
DDRB2 64MB/128MB/256MB/512MB/1GB
*1
Max is
4GB
***Only for reference***
Installing DDR Module
1. Unlock a DIMM slot by pressing the retaining clips
outward. Align a DIMM on the slot such that the
notch on the DIMM matches the break on the slot.
2. Insert the DIMM vertically and firmly into the slot
until the retaining chip snap back in place and the
DIMM is properly seated.
Jumpers, Headers, Connectors & Slots
Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~5, Bus Master, and Ultra DMA 33/ 66/ 100 functionality. It has two HDD
connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slave drive, so you can connect
up to four hard disk drives. The first hard drive should always be connected to
IDE1.
Peripheral Component Interconnect Slots: PCI1-3
This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.

8
Accelerated Graphics Port Slot: AGP1
Your monitor will attach directly to that video card. This motherboard supports
video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port
(AGP). An AGP card will take advantage of AGP technology for improved video
efficiency and performance, especially with 3D graphics.
Communication Network Riser Slot: CNR1
The CNR specification is an open Industry Standard Architecture, and it defines a
hardware scalable riser card interface, which supports modem only.
Serial ATA Connector: JSATA1/JSATA2
The motherboard has a PCI to SATA Controller with 2 channels SATA interface, it
satisfies the SATA 1.0 spec and can transfer data with 1.5GHz speed.
Front Panel Connector: JPANEL1
SPK
PWR_LED
HLED
SLP
RST
224
IR
123
IRON/OFF
Pin Assignment Function Pin Assignment Function
1 +5V 2 Sleep Control
3 NA 4 Ground Sleep
Button
5 NA 6 NA NA
7 Speaker
Speaker
Connector
8 Power LED (+)
9 HDD LED (+) 10 Power LED (+)
11 HDD LED (-) Hard Drive
LED 12 Power LED (-)
POWER
LED
13 Ground 14 Power Button
15 Reset Control Reset
Button 16 Ground Power-on Button
17 NA 18 KEY
19 NA 20 KEY
21 +5V 22 Ground
23 IRTX
IrDA
Connector
24 IRRX
IrDA
Connector
JPANEL1

9
Power Connectors: JATXPWER1/ JATXPWR2
PIN Assignment PIN Assignment
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Ground 13 Ground
4 +5V 14 PS_ON
5 Ground 15 Ground
6 +5V 16 Ground
7 Ground 17 Ground
8 PW_OK 18 -5V
9 +5V_SB 19 +5V
20
11
10
1
JATXPWR1
10 +12V 20 +5V
PIN Assignment PIN Assignment
1 +12V 3 Ground
12
3
JATXPWR2 2 +12V 4 Ground
5V / 5VSB Selection for KB: JKBV1
JKBV1 Assignment Description
1 3
Pin 1-2 close +5V 5V for keyboard and mouse
1 3
Pin 2-3 close +5V_SB 5V standby for keyboard and mouse to
power on your system

10
5V/ 5VSB Selection for USB: JUSBV1/ JUSBV2/JUSBV3_4
JUSBV1/JUSBV2/
JUSBV3_4 Assignment Description
1 3
Pin 1-2 close
+5V 5V JUSBV1 for JUSB1 port
5V JUSBV2 for JRJ45USB1 port
5V JUSBV3_4 for JUSB2/3 ports
1 3
Pin 2-3 close
+5V_SB JUSBV1 5V standby to power on
JUSB1 port
JUSBV2 5V standby to power on
JRJ45USBV1 port
JUSBV3_4 5V standby to power on
JUSB2/3 ports
Clear CMOS Jumper: JCMOS1
JCMOS1 Assignment
1 3
Pin 1-2 Close Normal Operation (default)
1 3
Pin 2-3 Close Clear CMOS Data
※Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 1-2 Close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 2-3 Close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
Case Open Connector: JCL1
Pin Assignment
1 Case Open Signal
12
JCL1 2 Ground

11
Serial ATA Connector: JSATA1/ JSATA2
Pin Assignment Pin Assignment
1 Ground 2 TX+
4 TX- 4 Ground
5 RX- 6 RX+
1
23
4
56
7
JSATA1/ JSATA2 7 Ground
AUDIO DJ Connector: JDJ1
Pin Assignment Pin Assignment
1 SMBDATA 2 SMBCLK
3 INT_B 4 KEY
15
JDJ1
5 ATX_PWROK
Game Header: JGAME1
1
216
15
JGAME1
Pin Assignment Pin Assignment
1 +5V 2 +5V
3 GP6 4 GP4
5 GP2 6 GP0
7 MIDI-OUTR 8 Ground
9 GP3 10 Ground
11 GP7 12 GP1
13 MIDI-INR 14 GP5
15 NA 16 +5V
CD-ROM Audio-In Header: JCDIN1/JCDIN2
Pin Assignment
1 Left Channel Input
2 Ground
3 Ground
1
JCDIN1/2 4 Right Channel Input

12
Front Panel Audio Header: JAUDIO1
1
213 14
JAUDIO1
Pin Assignment Pin Assignment
1 Mic In 2 Ground
3 Mic Power 4 Audio Power
5 RT Line Out 6 RT Line Out
7 Reserved 8 Key
9 LFT Line Out 10 LFT Line Out
11 RT Line In 12 RT Line In
13 LET Line In 14 LET Line In
Digital Audio Connector: JSPDIF_OUT1
Pin Assignment
1 +5V
2 SPDIF_OUT
1
JSPDIF_OUT1 3 Ground
Wake On LAN Header: JWOL1
Pin Assignment
1 +5V_SB
2 Ground
1
JWOL1 3 Wake up
Front USB Header: JUSB2/3
Pin Assignment Pin Assignment
1 +5V(fused) 2 +5V(fused)
3 USBP 4 USBP
5 USBP 6 USBP
7 Ground 8 Ground
2
1
10
9
JUSB2/3 9 KEY 10 NC

13
Back Panel Connectors
1 3
13
Keyboard
Mouse
COM1
JCOM1
JKBMS1
USB
JUSB1
USB
JRJ45USB1
Speaker Out
Line In/ Surround
Mic In/ Bass&Center
JAUDIO
LAN
Parallel
JVGA1

14
Español
Características del P4TSV
A. Hardware
CPU
Proporciona Socket-478.
Soporta procesador Intel Pentium 4 de hasta 3.06GHz.
Front Side Bus a 400/533/800MHz.
Soporta Hyper-Threading.
Soporta Northwood y Prescott CPU. (No soporta CPU Willamette)
Chipset
North Bridge: Intel 865G
South Bridge: Intel ICH5.
Memoria Principal
Soporta una o dos DDR canal de datos de 64-bit wide con 1 o 2 DIMMs por canal.
Banda ancha disponible hasta 3.2GB/s (DDR400) para modo de canal simple y
modo de canal doble 6.4GB/s (DDR 400).
Soporta tecnologia DDR de 128-MB, 256-Mb, 512-Mb y 1 GB.
Soporta solamente dispositivos DDR x8, x16.( No soporta DIMMs registered o
DIMMs de doble cara X 16)
Soporta dispositivos de 4 bancos.
Tamaño de memoria máxima 4GB.
Super I/O
Chip: ITE IT8712F.
Interface Low Pin Count.
Proporciona funcionalidad legacy Super I/O.
Environment Control initiatives,
- H/W Monitor
- Controlador Fan Speed
- Función ITE "Smart Guardian"
Ranuras
Tres ranuras de 32-bit PCI bus master.
Una ranura CNR.
Una ranura AGP 4X/ 8X.
IDE Onboard
Soporta cuatro discos IDE.
Soporta modo PIO 5, modo Bride y Ultra DMA 33/66/100 Bus Modo Master.
Soporta 2 puertos Serial ATA (SATA).
- Conforma con la especificación SATA 1.0

15
- Transferencia de datos de hasta 1.5 GB/s
LAN
Chip: RTL8100B.
Soporta 10 Mb/s y 100 Mb/ auto-negociación
Capacidad Half/ Full duplex.
Soporta administración ACPI
AC’97 Sound Codec Onboard
Chip: CMI9739A.
Conforma con la especificación AC’97.
Interface AC97 2.2.
Soports 6 canales.
Periféricos Onboard
a. Parte Trasera
1 puerto serie.
1 puerto paralelo. (modo SPP/EPP/ECP)
1 puerto VGA.
Puerto de Audio vertical.
1 LAN RJ-45.
Soporta ratón PS/2 y teclado PS/2.
4 puertos USB2.0.
b. Parte Frontal
1 puerto para disquetera soporta 2 FDDs con 360K, 720K, 1.2M, 1.44M y 2.88
Mbytes.
4 puertos USB2.0.
Dimensiones
Forma de Factor Micro ATX: 24.4 X 24.4cm (W X L)
B. BIOS & Software
BIOS
Award legal BIOS.
Soporta APM1.2.
Soporta ACPI.
Soporta función USB.
Software
Soporta Warpspeeder™, 9th Touch™, FLASHER™, StudioFun!™ (opcional).
Ofrece el más alto funcionamiento para Windows 98 SE, Windows 2000,
Windows Me, Windows XP, SCO UNIX etc.

16
Contenido del Paquete
Cable HDD X 2
Cable FDD X1
Manual del Usuario X1
Configuración Completa del Driver CD X1
Aplicación StudioFun! CD X 1 (opcional)
Cable USB 2.0 X1 (opcional)
Cable S/PDIF X 1 (opcional)
Panel Trasero I/O para carcasa Micro ATX X1 (opcional)
Cable Serial ATA X1
Cable de Interruptor de Corriente para Serial ATA X1
Cómo instalar un Puente
La ilustración muestra cómo instalar un puente. Cuando el Jumper Cap está ubicado en
los contactos, el puente está en “close”. Si no hay Jumper Cap ubicado en los contactos,
el puente está en ”open”. La siguiente ilustración muestra un contacto 3 en el que los
contactos 1y 2 están “close” cuando el Jumper Cap está ubicado en los dos contactos.
Puente open Puente close Contacto 1-2 close
Instalación del CPU
Paso 1:
Paso 1:Paso 1:
Paso 1: Empuje la palanca hacia afuera del socket y levante la palanca hasta un ángulo
de 90 grados.
Paso
PasoPaso
Paso 2
22
2:
::
:Fíjese por el punto blanco o márgen cortado. El punto blanco o márgen cortado
debería apuntar hacia el pivote de la palanca. La CPU solamente se fijará en una
sola correcta orientación.
P
PP
Paso
asoaso
aso 3:
3:3:
3: Tome el CPU firmemente hacia abajo, y cierre la palanca para completar la
instalación.

17
P
PP
Paso
asoaso
aso 4:
4:4:
4: Ponga el ventilador de la CPU en el CPU y asegúrelo. Conecte el cable de
corriente del ventilador de la CPU al JCFAN1. Ésto completa la instalación.
p
pp
paso
asoaso
aso 1 p
1 p1 p
1 paso
asoaso
aso 2 p
2 p2 p
2 paso
asoaso
aso 3 p
3 p3 p
3 paso
asoaso
aso 4
44
4
Cabezal del Sistema de Ventilación del CPU: JCFAN1
Contacto Asignación
1 Tierra
2 +12V
1
JCFAN1 3 FAN RPM Sense
Cabezal del Sistema de Ventilación: JSFAN1
Contacto Asignación
1 Tierra
2 +12V
1
JSFAN1
3 FAN RPM Sense
Módulos DDR DIMM: DDRA1-2, DDRB1-2
Soporta hasta cuatro DDR DIMMs (dos DIMMs por canal), doble o/y una cara.
Para manejarse con el Dual Channel, los DIMMs deben ser insertados en
pares idénticos. Debe ser la combinacin del DDRA1+DDRB1 (DIMMs azules)
o DDRA2+DDRB2 (DIMMs blancos). Para más información sobre la operación
del Dual Channel por favor entre a la página web: www.biostar.com.tw)
DRAM Tiempo de Acceso: 2.5V Unbuffered/ no registered (sin ECC) DDR
SDRAM PC2100/ PC2700/ PC3200 Tipo requerido.
DRAM Tipo: 128MB/ 256MB/ 512MB/ 1GB Módulo DIMM (184 contactos)

18
Total del Tamaño de la Memoria con Unbuffered/ Registered DIMMs
Localización del
Socket DIMM Módulo DDR Total del Tamaño de la
Memoria
(MB)
DDRA1 64MB/128MB/256MB/512MB/1GB
*1
DDRA2 64MB/128MB/256MB/512MB/1GB
*1
DDRB1 64MB/128MB/256MB/512MB/1GB
*1
DDRB2 64MB/128MB/256MB/512MB/1GB
*1
Máxima
4GB
***Solamente para referencia***
Instalación del Módulo DDR
1. Abra una ranura de DIMM presionando el clip
de retención hacia afuera. Aliñe el DIMM en la
ranura tales que la muesca en el DIMM encaje
en la cumbrera de la ranura.
2. Inserte el DIMM verticalmente y firmemente en
la ranura hasta que el clip de retención vuelva a
su posición original y el DIMM esté
correctamente colocado.