Biostar P4TDP Pro User manual

P
P
P4
4
4T
T
TD
D
DP
P
P P
P
Pr
r
ro
o
o
i
FCC Statement and Copyright
This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in a
particular installation.
The vendor makes no representations or warranties with respect to the
contents here of and specially disclaims any implied warranties of
merchantability or fitness for any purpose. Further the vendor reserves the
right to revise this publication and to make changes to the contents here of
without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole is not allowed without
first obtaining the vendor’s approval in writing.
The content of this user’s is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

C
C
Co
o
on
n
nt
t
te
e
en
n
nt
t
ts
s
s
ii
ENGLISH ................................................................................................ 1
P4TDP Pro Features........................................................................................................1
Package contents............................................................................................................2
Layout of P4TDP Pro.......................................................................................................2
CPU Installation...............................................................................................................3
DDR DIMM Modules: DDR1-2..........................................................................................4
Jumpers, Headers, Connectors & Slots.........................................................................5
ESPAÑOL ..............................................................................................11
Características del P4TDP Pro.....................................................................................11
Contenido del Paquete .................................................................................................12
Disposición del P4TDP Pro ..........................................................................................12
Instalación de la CPU....................................................................................................13
Módulos DDR DIMM: DDR1-2 .......................................................................................14
Puentes, Cabezales, Conectores y Ranuras................................................................15
DEUTSCH............................................................................................. 21
Merkmale des P4TDP Pro .............................................................................................21
Verpackungsinhalt ........................................................................................................22
Layout des P4TDP Pro..................................................................................................22
Installation der CPU......................................................................................................23
DDR-DIMM-Modules: DDR1-2.......................................................................................24
Jumpers, Headers, Anschlüsse & Slots ......................................................................25
WARPSPEEDER................................................................................... 31
Introduction...................................................................................................................31
System Requirement.....................................................................................................32
Installation.....................................................................................................................32
Usage.............................................................................................................................34
TROUBLE SHOOTING.......................................................................... 42
SOLUCIÓN DE PROBLEMAS............................................................... 43
PROBLEMLÖSUNG.............................................................................. 44

1
English
P4TDP Pro Features
! Use Intel 845E/ ICH2 Chipset, ITE I/O- IT8712.
! Contains on board I/O facilities, which include two serial port, a parallel port,
a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB ports, a game
port .
! Supports the Intel Pentium 4®(Socket 478) processor up to 2.4GHz.
! Supports Ultra 100/66/33, BMIDE and PIO modes.
! Supports up to 2 DDR 200/ 266/ Fuzzy333 MHz devices, running at 400
MHz/ 533 Front Side Bus frequency.
! Supports five 32-bit PCI Bus slots, and one CNR Slot (Type A only) .
(If use the onboard CODEC, the CNR slot only support slave card. If
use H/W Audio, then the CNR slot only support primary card)
! Supports USB1.1.
! Supports USB2.0(optional).
! Complies with PC ATX form factor specifications.
! Supports popular operating systems such as Windows 98, Windows NT,
Windows 2000, Windows ME, Windows XP, LINUX and SCO UNIX.
! DIMM Power Selection by BIOS setup to adjust DDR DIMM voltage. (Once
encounter the DDR DIMM compatible problem, try to adjust the DDR
Voltage to fix the compatible program.)
! Intel®AC’97 2.2 compatible.
! High S/N ratio meets PC 99 requirements.
! 6CH , applicable for leading motherboard chipsets.
! Line-in phone-jack share with rear out .
! Mic-in phone-jack share with Bass and Center.

2
Package contents
! HDD Cable X 1, FDD Cable X 1, Fully Setup Driver CD X 1
! USB Cable X 2 (Optional)
Layout of P4TDP Pro
DDR 1
DDR 2
INTEL 845E
Socket 478
JAUDIO1
1
2
K/B
&
Mouse
JKBMS1
JUSB1
JPRNT1
JCOM1
JCOM2
COM1
Parallel Port
PCI3
CNR1
BAT1
JATXPWR1
JCFAN1
JUSB2
AGP1
JUSBV1
JCDIN1
JGAME1
GAME Port
SP-OUT
LINE-IN
MIC-IN
JATXPWR2
PCI1
PCI2
PCI4
Codec
(optional)
1
2
USB 2.0
Chip
(optional)
H/W
AUDIO
Chip
(optional)
BIOS
I/O
JDIMMVOLT1
1
2
JKBV1
IDE1
JCMOS1
INTEL ICH2
JUSBV4
J1
PRIMARY IDE CONN.
JUSBV2_3
1
JSFAN1
PCI5
1JPANEL1
FDD1
JWOL1
1
223 24
1
SECONDARY IDE CONN.
FLOPPY DISK CONN.
IDE2
JUSB4
JUSB3
2
2

3
CPU Installation
1. Pull the lever sideways away from the socket then raise the lever up
to 90-degree angle.
2. Locate Pin A in the socket and lock for the white dot or cut edge in
the CPU. Match Pin A with the white dot/cut edge then insert the
CPU.
3. Press the lever down. Then Put the fan on the CPU and buckle it
and put the fan’s power port into the JCFAN1, then to complete the
installation.
CPU/ System Fan Headers: JCFAN1/ JSFAN1
CPU
JCFAN1 JSFAN1
Ground12V
Sense
1
Ground12V
Sense
1

4
DDR DIMM Modules: DDR1-2
DRAM Access Time: 2.5V Unbuffered DDR 200/266/Fuzzy 333 MHz
Type required (x16 does not support).
DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184
pin)
DIMM Socket
Location DDR Module Total Memory Size (MB)
DDR 1 64MB/128MB/256MB/512MB/1GB
*1
DDR 2 64MB/128MB/256MB/512MB/1GB
*1
Max is
2GB
* The list shown above for DRAM configuration is only for reference.
How to install a DIMM Module
1. The DIMM socket has a
“ Plastic Safety Tab”, and the
DIMM memory module has an
“Asymmetrical notch”, so the
DIMM memory module can only
fit into the slot in one direction.
2. Push the tabs out. Insert the
DIMM memory modules into the
socket at a 90-degree angle, then
push down vertically so that it will
fit into the place.
3. The Mounting Holes and plastic
tabs should fit over the edge and
hold the DIMM memory modules
in place.

5
Jumpers, Headers, Connectors & Slots
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that
provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100
functionality. It has two HDD connectors IDE1 (primary) and IDE2
(secondary).
The IDE connectors can connect a master and a slave drive, so you can
connect up to four hard disk drives. The first hard drive should always be
connected to IDE1.
Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This
connector supports the provided floppy drive ribbon cables.
Communication Network Riser Slot: CNR1
The CNR specification is an open Industry Standard Architecture, and it
defines a hardware scalable riser card interface, which supports audio,
network and modem only (slave card only) .
(If use the onboard CODEC, the CNR slot only support slave card.
If use H/W Audio, then the CNR slot only support primary card)
Accelerated Graphics Port Slot: AGP1
Unlike the mouse ports, keyboard ports and printer ports this
motherboard does not have built in video facilities and therefore requires
a video card for one of the expansion slots. Your monitor will attach
directly to that video card. This motherboard supports video cards for
PCI, and it is also equipped with an Accelerated Graphics Port (AGP).
An AGP card will take advantage of AGP technology for improved video
efficiency and performance, especially with 3D graphics.
Peripheral Component Interconnect Slots: PCI1-5
This motherboard is equipped with 5 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for
expansion cards, which has, supplanted the older ISA bus standard in
most ports. This PCI slot is designated as 32 bits.

6
Power Connectors: JATXPWR1/ JATXPWR2
DIMM Power Selection Connector: JDIMMVOLT1
(Optional)
Wake On LAN Header: JWOL1
WOL1
1
5V_SB Wakeup
Ground
JATXPWR1
(ATX Main Power Conn.)
JATXPWR1
(ATX Main Power Conn.)
JATXPWR2
(ATX 12V Power Conn.)
1
2
JDIMMVOLT
Jump Open==> 2.5V
Pin 1-2 on ==> 2.6V
Pin 3-4 on ==> 2.7V
Pin 5-6 on ==> 2.8V
Pin 7-8 on ==> 2.9V
(Default ==> 2.5V)

7
Front USB Header: JUSB2/ JUSB3(Optional)
/ JUSB4(Optional)
JUSB1
(Located in
the back
panel)
JUSB2 JUSB3 JUSB4
Before
using USB
2.0 Chip
USB 1.1
Chip USB 1.1 Chip X X
After using
USB 2.0
Chip
USB 2.0
Chip USB 1.1 Chip USB 1.1 Chip USB 2.0 Chip
5V/ 5VSB Selection for USB: JUSBV1/2_3/
JUSBV4(Optional)
5V/ 5VSB Selection for KB: JKBV1
JUSB2/3/4
2
1
Pin1,2 ==> +5V
Pin3,4 ==> Data(-)
Pin5,6 ==> Data(+)
Pin7,8 ==> Ground
Pin9 ==> KEY
Pin10 ==> NA
1
JUSBV1/2_3/4
Pin 1-2 on ==> 5V
Pin 2-3 on ==> 5V_SB
Pin 1-2 on ==> 5V
Pin 2-3 on ==> 5V_SB
1
JKBV1

8
5V/ 5VSB Selection for USB WAKE-UP: J1(Optional)
# JUSB1 and JUSB4 will change to 5V_SB after using USB 2.0 Chip
(VT6202) and the 5V/ 5VSB Selection for USB WAKE-UP (J1) will be
set in “on” mode.
Audio Subsystem: JAUDIO1/ JCDIN1
1
J1
Pin 1-2 ==>
Pin 2-3 ==> off
on
1
2
JAUDIO1
(Front Audio Header)
1
JCDIN1
(CD-ROM Audio-In Header)
2JAUDIO1
1
29 10
Pin
1
3
5
7
9
Pin
2
4
6
8
10
Mic In
Mic Power
RT Line Out
Reserved
LFT Line Out
Assignment Ground
Audio Power
RT Line Out
NC
Assignment
LFT Line Out

9
Front Panel Connector: JPANEL1
SPK
PWR_LED
HLED
SLP
RST
224
IR
123
IRON/OFF
SPK ==> Speaker Conn.
HLED ==> Hard Driver LED
RST ==> Reset Button
IR ==> Infrared Conn.
SLP ==> Sleep Button
PWR_LED ==> Power LED
ON/ OFF ==> Power-on Button
(+) (-)
(+) (-)(+)
12
Front Panel Audio Connector/JumperBlock
910 Audio line out signals are routed
to the back panel audio line out connector.
Pin 5 and 6
Pin 9 and 10
Audio line out and mic in signals are
available for front panel audio connectors.
3
5
7
4
6
12
910
3
5
7
4
6No jumpers
installed
Jumper Setting Configuration

10
Clear CMOS Jumper: JCMOS1
Back Panel Connectors
PS/2
Keyboard
PS/2
Mouse
COM1
Game Port
JGAME1
JCOM1
JKBMS1
USB
COM1 Mic
In
JCOM2
JPRNT1
COM1
4 Channel Speakers 6 Channel Speakers
Speaker Out Line In/
Rear Speaker Mic In Speaker Out
Line In/
Rear Speaker Mic In/ Center & Bass
JCMOS1
Clear CMOS
Data
Pin 1-2 on
Normal
Operation
(default)
Assignment
1
Pin 2-3 on
1

11
Español
Características del P4TDP Pro
! Usa Chipset Intel 845E/ ICH2, ITE I/O- IT8712.
! Contiene facilidades I/O integrados en la placa madre en el que incluye
dos puertos en serie, un puerto paralelo, un puerto para ratón PS/2, un
puerto para teclado PS/2, puertos de audio, puertos USB y un puerto de
juego .
! Soporta procesadores Intel Pentium 4®(Socket 478) de hasta 2.4GHz.
! Soporta Ultra 100/66/33, BMIDE y modos PIO.
! Soporta hasta 2 dispositivos DDR 200/266/Fuzzy 333 MHz, corriendo a
400 MHz/ 533 MHz frecuencia Front Side Bus.
! Soporta cinco ranuras PCI 32-bit y una ranura CNR (solamente de Tipo
A) .
(Si usa CODEC integrado en la placa madre, la ranura CNR solamente
soporta tarjeta esclava. Si usa H/W Audio, la ranura CNR solamente
soporta tarjeta primaria.)
! Soporta USB1.1.
! Soporta USB2.0 (opcional).
! Compatible con las especificaciones del factor de forma de tamaño de PC
ATX.
! Soporta sistemas operativos populares tales como Windows 98, Windows
NT, Windows 2000, Windows ME, Windows XP, LINUX y SCO UNIX.
! Corriente de Selección DIMM para configuración BIOS utilizado para
ajustar voltaje DDR DIMM. (Si se encuentra con un problema compatible al
DDR DIMM, trate de ajustar el voltaje DDR para fijar con el programa
compatible.)
! Compatible con Intel®AC’97 2.2.
! Alto S/N ratio para requerimientos PC 99.

12
! 6CH , aplicable para chipsets de principales placas madres.
! Entrada de Línea phone-jack compartido con el rear out. Micrófono
phone-jack compartido con Bass y Center.
Contenido del Paquete
! Cable HDD X 1, Cable FDD X 1, Configuración Completa del Driver CD X1
! Cable USB X 2 (Opcional)
Disposición del P4TDP Pro
DDR 1
DDR 2
INTEL 845E
Socket 478
JAUDIO1
1
2
JKBMS1
JUSB1
JPRNT1
JCOM1
JCOM2
COM1
Parallel Port
PCI3
CNR1
BAT1
JATXPWR1
JCFAN1
JUSB2
AGP1
JUSBV1
JCDIN1
JGAME1
GAME Port
SP-OUT
LINE-IN
MIC-IN
JATXPWR2
PCI1
PCI2
PCI4
Codec
(optional)
1
2
USB 2.0
Chip
(optional)
H/W
AUDIO
Chip
(optional)
BIOS
I/O
JDIMMVOLT1
1
2
JKBV1
IDE1
JCMOS1
INTEL ICH2
JUSBV4
J1
PRIMARY IDE CONN.
JUSBV2_3
1
JSFAN1
PCI5
1JPANEL1
FDD1
JWOL1
1
223 24
1
SECONDARY IDE CONN.
FLOPPY DISK CONN. IDE2
JUSB4
JUSB3
2
2

13
Instalación de la CPU
1. Tire de la palanca del lado del zócalo, luego levante la palanca
hasta un ángulo de 90 grados.
2. Sitúe el contacto A del zócalo y busque el punto blanco o corte el
borde en la CPU. Empareje el contacto A con el punto blanco/
corte del borde, luego inserte la CPU.
3. Presione la palanca para abajo. Ponga el ventilador en la CPU y
abróchelo. Luego ponga el puerto de corriente del ventilador en el
JCFAN1. Y ya habrá completado su instalación.
CPU/ Cabezales del Sistema de Ventilación: JCFAN1/
JSFAN1
CPU
JCFAN1 JSFAN1
Tierra12V
Sense
1
Tierra12V
Sense
1

14
Módulos DDR DIMM: DDR1-2
DRAM Tiempo de Acceso: 2.5V Unbuffered DDR 200/266/Fuzzy 333
MHz Tipo requerido (no soporta x16)
DRAM Tipo: 64MB/ 128MB/ 256MB/ 512MB/ 1GB Módulos DIMM (184
contactos)
Localización
del Zócalo
DIMM
Módulo DDR Total del
Tamaño de
Memoria (MB)
DDR 1 64MB/128MB/256MB/512MB/1GB
*1
DDR 2 64MB/128MB/256MB/512MB/1GB
*1
Máximo de
2GB
* La lista de arriba para la configuración DRAM es solamente para uso
de referencia.
Cómo instalar un Módulo DIMM
1. El zócalo DIMM tiene una
lengüeta plástica de seguridad y
el módulo de memoria DIMM
tiene una muesca asimétrica, así
el módulo de memoria DIMM
puede caber solamente en la
ranura de una sóla dirección.
2. Tire la lengüeta hacia afuera.
Inserte los módulos de memoria
DIMM en el zócalo a los 90
grados, luego empuje hacia abajo
verticalmente de modo que
encaje en el lugar.
3. Los agujeros de montaje y las
lengüetas plásticas deben caber por sobre el borde y sostenga los
módulos de memoria DIMM en el lugar.

15
Puentes, Cabezales, Conectores y Ranuras
Conectores del Disco Duro: IDE1/ IDE2
La placa madre tiene un controlador de 32-bit PCI IDE que proporciona
Modo PIO 0~4, Bus Master, y funcionalidad Ultra DMA / 33/ 66/ 100.
Tiene dos conectores HDD IDE1 (primario) y IDE2 (secundario).
El conector IDE puede conectar a un master y un drive esclavo, así
puede conectar hasta cuatro discos rígidos. El primer disco duro debe
estar siempre conectado al IDE1.
Conectores para el Disquete: FDD1
La placa madre proporciona un conector estándar del disquete (FDC)
que soporta 360K, 720K, 1.2M, 1.44M y 2.88M tipos de disquete. Éste
conector utiliza los cables de cinta proporcionados por el disquete.
Ranura de la Banda de Suspensión de Comunicación y
Red: CNR1
La especificación CNR es una abierta Industria de Arquitectura Estándar,
que define una tarjeta de interface escalable del hardware en el que
soporta solamente audio, network y modem (solamente tarjeta esclava).
(Si usa CODEC integrado en la placa madre, la ranura CNR
solamente soporta tarjeta esclava. Si usa H/W Audio, la ranura
CNR solamente soporta tarjeta primaria.)
Accelerated Graphics Port Slot: AGP1
Su monitor se fijará directamente a la tarjeta de video. Ésta placa madre
soporta tarjetas de video para ranuras PCI, y también está equipado con
un Puerto Acelerado para Gráficos. Ésta tarjeta AGP tomará ventaja de
la tecnología del AGP para el mejoramiento de la eficiencia y
funcionamiento del video, especialmente con gráficos 3D.
Ranura de Interconexión del Componente Periférico:
PCI1-5
Ésta placa madre está equipada con 5 ranuras estándar PCI. PCI es la
sigla para Interconexión del Componente Periférico, y es un bus
estándar para tarjetas de expansión en el que suplanta a la antigua bus
estándar ISA, en su mayoría de las partes. Ésta ranura PCI está
diseñado con 32 bits

16
Conectores de Corriente: JATXPWR1/ JATXPWR2
Conector de Selección de la Corriente DIMM:
JDIMMVOLT1 (Opcional)
Cabezal Wake On LAN: JWOL1
JATXPWR1
(ATX Conector de Corriente Principal)
JATXPWR2
(ATX 12V Conector de Corriente)
1
2
JDIMMVOLT
Puente Abierto==> 2.5V
Contacto 1-2 on ==> 2.6V
Contacto 3-4 on ==> 2.7V
Contacto 5-6 on ==> 2.8V
Contacto 7-8 on ==> 2.9V
(Default ==> 2.5V)
WOL1
1
5V_SB Wake up
Tierra

17
Cabezal Frontal USB: JUSB2/ JUSB3(Opcional)/
JUSB4(Opcional)
JUSB1
(Ubicado en
el panel
trasero)
JUSB2 JUSB3 JUSB4
Antes de
usar Chip
USB 2.0
USB 1.1
Chip USB 1.1 Chip X X
Luego de
usar Chip
USB 2.0
USB 2.0
Chip USB 1.1 Chip USB 1.1 Chip USB 2.0 Chip
5V/ 5VSB Selección para USB: JUSBV1/2_3
/ JUSBV4(Opcional)
5V/ 5VSB Selección
para KB: JKBV1
1
JUSBV1/2_3/4
Contacto 1-2 on ==> 5V
Contacto 2-3 on ==> 5V_SB
1
JKBV1
Contacto 1-2 on ==> 5V
Contacto 2-3 on ==> 5V_SB
JUSB2/3/4
2
1
Contacto1,2 ==> +5V
Contacto3,4 ==> Dato(-)
Contacto5,6 ==> Dato(+)
Contacto7,8 ==> Tierra
Contacto9 ==> KEY
Contacto10 ==> NA

18
5V/ 5VSB Selección para USB WAKE-UP: J1 (Opcional)
# JUSB1 y JUSB4 cambiará a 5V/5VSB luego de usar el Chip USB 2.0
(VT6202) y el la función 5V/5VSB Selección para USB WAKE-UP (J1)
se fijará al modo “on”.
Subsistema de Audio: JAUDIO1/ JCDIN1
Contacto 1-2 ==>
Contacto 2-3 ==>
on
off
1
J1
1
2
JAUDIO1
(Cabezal Frontal
de Audio)
1
JCDIN1
(Cabezal deEntrada
de Audio CD-ROM)
2JAUDIO1
1
29
10
Contactos
1
3
5
7
9
Contactos
2
4
6
8
10
Entrada del MIC
Corriente del MIC
RT Salida de Linea
Reservado
LFT Salida de Linea
Asignacion Tierra
Corriente de Audio
RT Salida de Linea
Key
Asignacion
LFT Salida de Linea