Biostar BICHT-PBA User manual

FCC Informaon and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to
radio communicaons. There is no guarantee that interference will not occur in a parcular installaon.
The vendor makes no representaons or warranes with respect to the contents here and specially disclaims
any implied warranes of merchantability or tness for any purpose. Further the vendor reserves the right
to revise this publicaon and to make changes to the contents here without obligaon to nofy any party
beforehand.
Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the vendor’s approval
in wring.
The content of this user’s manual is subject to be changed without noce and we will not be responsible for
any mistakes found in this user’s manual. All the brand and product names are trademarks of their respecve
companies.
Dichiarazione di conformità sinteca
Ai sensi dell’art. 2 comma 3 del D.M. 275 del
30/10/2002
Si dichiara che questo prodoo è conforme
alle normave vigen e soddisfa i requisi
essenziali richies dalle direve
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaraon of conformity
We declare this product is complying with the
laws in force and meeng all the essenal
requirements as specied by the direcves
2004/108/CE, 2006/95/CE and 1999/05/CE
whenever these laws may be applied

2 | Table Of Contents
BIBD-PBA User’s Manual
Table Of Contents
FCC Informaon and Copyright ������������������������������������������������������������������������������� 1
Chapter 1: Introducon������������������������������������������������������������������������������������������� 3
1.1 Before You Start .....................................................................................................................................3
1.2 Specicaons .........................................................................................................................................4
1.3 Rear / Front Panel Connectors ...............................................................................................................5
1.4 Motherboard Layout..............................................................................................................................6
Chapter 2: Hardware installaon����������������������������������������������������������������������������� 7
2.1 Central Processing Unit (CPU)................................................................................................................7
2.2 Jumpers / Slot / Headers / Connectors ..................................................................................................7
Chapter 3: BIOS Setup������������������������������������������������������������������������������������������� 11
3.1 Main Menu ..........................................................................................................................................12
3.2 Advanced Menu...................................................................................................................................13
3.3 Chipset Menu.......................................................................................................................................19
3.4 Security Menu......................................................................................................................................29
3.5 Boot Menu ...........................................................................................................................................31
3.6 Exit Menu.............................................................................................................................................33

Chapter 1: Introducon | 3
BICHT-PBA User’s Manual
Chapter 1: Introducon
1.1 Before You Start
Thank you for choosing our product. Before you start installing the motherboard, please make sure you
follow the instrucons below:
• Prepare a dry and stable working environment with sucient lighng.
• Always disconnect the computer from power outlet before operaon.
• Before you take the motherboard out from an-stac bag, ground yourself properly by touching
any safely grounded appliance, or use grounded wrist strap to remove the stac charge.
• Avoid touching the components on motherboard or the rear side of the board unless necessary.
Hold the board on the edge, do not try to bend or ex the board.
• Do not leave any unfastened small parts inside the case aer installaon. Loose parts will cause
short circuits which may damage the equipment.
• Keep the computer from dangerous area, such as heat source, humid air and water.
• The operang temperatures of the computer should be 0 to 45 degrees Celsius.
• To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
Note
»
»The package contents may be dierent due to the sales region or models in which it was sold. For more
informaon about the standard package in your region, please contact your dealer or sales representave.

4 | Chapter 1: Introducon
BIBD-PBA User’s Manual
1.2 Specifications
CPU Intel® Atom™ Quad core x5-Z8350 Processor (2M Cache, up to 1.92 GHz)
Graphic
Integrated Intel® HD Graphics engine
Dual independent displays (Extended mode) as below two:
-- Integrated DVI-D
-- Integrated HDMI
Main Memory DDR3L 1600MHz SO-DIMM / 2GB/4GB, single channel ,1.35V
*Registered DIMM or ECC DIMM is not supported
Storage 1x Built-in 32/64GB eMMC Flash Onboard
1x Built-in Micro SD connector
Networking
LAN:
Realtek RTL8152B
10 / 100 Mb/s auto negoaon, Half / Full duplex capability
Wireless:
AMPAK AP6212 SIP Module (BCM43438) support 802.11 b/g/n, BT V4.0(colay AP6255, BCM43455)
Sound Codec Realtek Codec ALC5645, supports Line-out/Mic-in
USB
Intel® Atom™ x5-Z8350 Processor supports 3xUSB 2.0 Port and USB 3.0 OTG:
3x Super Speed (SS) ports (Backward Compable of USB 2.0 HS/FS/LS)
Built-in 1x GL854 (1 to 7 port USB 2.0 Hub IC):
1x USB 3.0 OTG on the front/rear IO Type A connector(with 5V standby and The current is 900mA)
3x USB 2.0 Bus on the front/Rear IO Type A connector(with 5V and The current is 500mA)
1x USB 2.0 Bus internal header 2x5 pins 2.54mm(with 5V and The current is 500mA)
1x USB 2.0 bus for M.2 socket (3G Module) from SOC
1x USB 2.0 bus for S/IC CHIP 10/100M LAN/RTL8152B for LAN Port
1x USB 2.0 bus for USB2.0 to 4 x UART IC(Fintek F81534)
Rear Panel I/O
1x DC12V Jack connector
1x DVI-I connector (Digital signal only)
1x HDMI Type A connector
2x USB 2.0 connector (with 5V and The current is 500mA)
1x RJ45 LAN connector (10/100 Mb/s)
1x micro SD connector
Front Panel I/O
1x USB 3.0 connector (with 5V standby and The current is 900mA)
1x USB 2.0 connector(with 5V standby and The current is 500mA)
2x Audio Jack(Line-out & Mic-in)
1x Power Buon(co-lay header)
1x 25pin FPC connector Integrated MIPI CSI 8M CAMERA connector
Internal I/O
1x M.2 B KEY socket for 3G Module
1x M.2 E KEY socket for 802.11b/g/n WIFI /BT Module
1x SIM connector
1x USB 2.0 Bus internal header 2x5 pins 2.54mm(with 5V and The current is 500mA)
1x 1*3 pins header, Clear CMOS Jumper seng
1x 1*2 pins header, Power buon header
2x 1*2 pins wafer for Codec AL5645 class D 2.5Wa/Channel Amp Speaker
1x Antenna connector
4 x 2*5 pins wafer,COM Port
3x 1*3 pins COM port mode selecon
Board Size 105 mm (W) x 146 mm (L), 3.5” SBC
Operaon Temperature 0°C ~ 40°C
Storage Temperature -40°C ~ 60°C
Relave Humidity 10% ~ 90% (non-condensing)
Cercaon CE / FCC Pre-scan
OS Driver Support Windows 10 (64 bits) OS , Ubuntu 16.04
RoHS Compliant Yes

Chapter 1: Introducon | 5
BICHT-PBA User’s Manual
1.3 Rear / Front Panel Connectors
Rear
Front
J1: DC-12V IN Power Jack

6 | Chapter 1: Introducon
BIBD-PBA User’s Manual
1.4 Motherboard Layout
»
» represents the 1st pin.

Chapter 2: Hardware installaon | 7
BICHT-PBA User’s Manual
Chapter 2: Hardware installaon
2.1 Central Processing Unit (CPU)
The mainboard includes an Intel® Celeron processor, and a cooler has been installed to provide sucient
cooling.
2.2 Jumpers / Slot / Headers / Connectors
M2_2: Half-size mPCIe Slot
SIM1: SIM card socket

8 | Chapter 2: Hardware installaon
BIBD-PBA User’s Manual
Jumper Seng
The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”,
if not, that means the jumper is “open”.
Pin opened Pin closed Pin 1-2 closed
JCMOS1: Clear CMOS Jumper
Placing the jumper on pin2-3 allows user to restore the BIOS safe seng and the CMOS data. Please
carefully follow the procedures to avoid damaging the motherboard.
Pin 1-2 Close: Normal Operaon (Default)
Pin 2-3 Close: Clear CMOS data
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for ve seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
JM0 / JM1 / JM2: COM port mode selecon
JM0: Pin 1-2 Close / JM1: Pin 1-2 Close / JM2: Pin 2-3 Close:
RS232(Default)
JM0: Pin 1-2 Close / JM1: Pin 1-2 Close / JM2: Pin 1-2 Close:
RS422
JM0: Pin 1-2 Close / JM1: Pin 2-3 Close / JM2: Pin 1-2 Close:
RS485

Chapter 2: Hardware installaon | 9
BICHT-PBA User’s Manual
F_USB2: USB 2.0 Connectors
This header allows you to connect addional USB 2.0 port.
Pin Assignment
1USB_VCC
2 USB_VCC
3 DM2
4 DM1
5DP2
6DP1
7 GND
8 GND
JSPK1/2: Audio Connector
Le Speaker (JSPK1)
Pin Assignment
1 SPKRP
2SPKPN
Right Speaker (JSPK2)
Pin Assignment
1SPKLP
2 SPKLN
JCOM1/2/3/4: COM Port Connector
Pin Assignment Pin Assignment
1-PDCD 2 PSIN
3 PSOUT 3 -PDTR
5GND 6 -PDSR
7 -PRTS 8 -PCTS
9RI 10 NA

10 | Chapter 2: Hardware installaon
BIBD-PBA User’s Manual
PWRBTN: Power Buon
Pin Assignment
1GND
2PWRBTN
ANT4: WIFI+BT Antenna

Chapter 3: BIOS Setup | 11
BICHT-PBA User’s Manual
Chapter 3: BIOS Setup
Introducon
The purpose of this manual is to describe the sengs in the AMI UEFI BIOS Setup program on this
motherboard. The Setup program allows users to modify the basic system conguraon and save these
sengs to NVRAM.
UEFI BIOS determines what a computer can do without accessing programs from a disk. This system
controls most of the input and output devices such as keyboard, mouse, serial ports and disk drives. BIOS
acvates at the rst stage of the boong process, loading and execung the operang system. Some
addional features, such as virus and password protecon or chipset ne-tuning opons are also included
in UEFI BIOS.
The rest of this manual will to guide you through the opons and sengs in UEFI BIOS Setup.
Plug and Play Support
This AMI UEFI BIOS supports the Plug and Play Version 1.0A specicaon.
EPA Green PC Support
This AMI UEFI BIOS supports Version 1.03 of the EPA Green PC specicaon.
ACPI Support
AMI ACPI UEFI BIOS support Version 1.0/2.0 of Advanced Conguraon and Power interface specicaon
(ACPI). It provides ASL code for power management and device conguraon capabilies as dened in the
ACPI specicaon, developed by Microso, Intel and Toshiba.
PCI Bus Support
This AMI UEFI BIOS also supports Version 2.3 of the Intel PCI (Peripheral Component Interconnect) local
bus specicaon.
DRAM Support
DDR3 SDRAM (Double Data Rate III Synchronous DRAM) is supported.
Supported CPUs
This AMI UEFI BIOS supports the latest CPU.
Using Setup
When starng up the computer, press <Del> during the Power-On Self-Test (POST) to enter the UEFI BIOS
setup ulity. In the UEFI BIOS setup ulity, you will see General Help descripon at the top right corner,
and this is providing a brief descripon of the selected item. Navigaon Keys for that parcular menu are
at the boom right corner, and you can use these keys to select item and change the sengs.
Note
»
»The default UEFI BIOS sengs apply for most condions to ensure opmum performance of the motherboard.
If the system becomes unstable aer changing any sengs, please load the default sengs to ensure system’s
compability and stability. Use Load Setup Default under the Exit Menu.
»
»For beer system performance, the UEFI BIOS rmware is being connuously updated. The UEFI BIOS informaon
described in this manual is for your reference only. The actual UEFI BIOS informaon and sengs on board may
be slightly dierent from this manual.
»
»The content of this manual is subject to be changed without noce. We will not be responsible for any mistakes
found in this user’s manual and any system damage that may be caused by wrong-sengs.

12 | Chapter 3: BIOS Setup
BIBD-PBA User’s Manual
3�1 Main Menu
Once you enter AMI UEFI BIOS Setup Ulity, the Main Menu will appear on the screen providing an
overview of the basic system informaon.
BIOS Informaon
Shows system informaon including UEFI BIOS version, model name, markeng name, built date, etc.
Total Memory
Shows system memory size, VGA shard memory will be excluded.
System Language
Choose the system default language.
System Date
Set the system date. Note that the ‘Day’ automacally changes when you set the date.
System Time
Set the system internal clock.
Access Level
Shows the access level of current user.

Chapter 3: BIOS Setup | 13
BICHT-PBA User’s Manual
3.2 Advanced Menu
The Advanced Menu allows you to congure the sengs of CPU, Power Management, and other system
devices.
Note
»
»Beware of that seng inappropriate values in items of this menu may cause system to malfuncon.
»
»The opons and default sengs might be dierent by RAM or CPU models.
ACPI Sengs
Enable ACPI Auto Conguraon
This item enables or disables BIOS ACPI auto conguraon funcon.
Opons: Enabled (Default) / Disabled
»
»The following items appear only when you set the Enable ACPI Auto Conguraon funcon to [Disabled].

14 | Chapter 3: BIOS Setup
BIBD-PBA User’s Manual
Enable Hibernaon
This item enables or disables system ability to hibernate (0S/S4 sleep state). This opon may be not
eecve with some 0Ss.
Opons: Enabled (Default) / Disabled
ACPI Sleep State
This item selects the highest ACPI sleep state the system will enter when the SUSPEND buon is pressed.
Opons: Suspend Disabled (Default)
Lock Legacy Resources
The item enables or disables Lock of Legacy Resources.
Opons: Disabled (Default) / Enabled
CPU Conguraon
Socket 0 CPU Informaon

Chapter 3: BIOS Setup | 15
BICHT-PBA User’s Manual
CPU Thermal Conguraon
DTS
This item Enabled or Disable Digital Thermal Semsor.
Opons: Disabled (Default) / Enabled
Limit CPUID Maximum
This item disabled for Windows XP.
Opons: Disabled (Default) / Enabled
Bi-direconal PROCHOT
When a processor thermal sensor trips (either core), the PROCHOT# will be driven. If bi-direcon is
enabled, external agents can drive PROCHOT# to throle the processor.
Opons: Enabled (Default) / Disabled
Intel Virtualizaon Technology
When enabled, a VMM can ulize the addional hardware capabilies provided by Vanderpool Technology.
Opons: Enabled (Default) / Disabled
Power Technology
This item enable the power management features.
Opons: Energy Ecient (Default) / Disabled / Custom
»
»The following items appear only when you set the Power Technology funcon to [Custom].
EIST
This item Enabled or Disabled Intel SpeedStep.
Opons: Enabled (Default) / Disabled
Turbo Mode
This item allows you to control the Turbo Mode.
Opons: Enabled (Default) / Disabled
P-STATE Coordinaon
This item allows you to change P-STATE Coordinaon type.
Opons: HW_ALL (Default) / SW_ALL / SW_ANY
Package C State limit
This item allows you to set Package C State limit.
Opons: C1 (Default) / C3 / C6 / C7

16 | Chapter 3: BIOS Setup
BIBD-PBA User’s Manual
Ooard SATA Controller Conguraon
SDIO Conguraon
SDIO Access Mode
This item allows you to control the SDIO Access Mode. Auto Opon: Access SD device in DMA mode if
controller supports it, otherwise in PIO mode. DMA Opon: Access SD device in DMA mode. PIO Opon:
Access SD device in PIO mode.
Opons: Auto (Default) / ADMA / SDMA / PIO

Chapter 3: BIOS Setup | 17
BICHT-PBA User’s Manual
USB Conguraon
XHCI Hand-O
This is a workaround for OSes without XHCI hand-o support. The XHCI ownership change should be
claimed by EHCI driver.
Opons: Enabled (Default) / Disabled
USB Mass Storage Driver Support
This item enable/disable USB Mass Storage Driver Support.
Opons: Enabled (Default) / Disabled
USB transfer me-out
The me-out value for Control, Bulk, and Interrupt transfers.
Opons: 20 sec (Default) / 1 sec / 5 sec / 10 sec
Device reset me-out
The item sets USB mass storage device Start Unit command me-out.
Opons: 20 sec (Default) / 10 sec / 30 sec / 40 sec
Device power-up delay
“Auto” uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor.
Opons: Auto (Default) / Manual
»
»The following items appear only when you set the Device power-up delay funcon to [Manual].
Device power-up delay in seconds
Delay range is 1 ~ 40 seconds, in one second increments.
Opons: 5 (Default)

18 | Chapter 3: BIOS Setup
BIBD-PBA User’s Manual
Plaorm Trust Technology
fTPM
This item enable/disable fTPM.
Opons: Disabled (Default) / Enabled

Chapter 3: BIOS Setup | 19
BICHT-PBA User’s Manual
3�3 Chipset Menu
This secon describes conguring the PCI bus system. PCI, or Personal Computer Interconnect, is a
system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when
communicang with its own special components.
Note
»
»Beware of that seng inappropriate values in items of this menu may cause system to malfuncon.
North Bridge

20 | Chapter 3: BIOS Setup
BIBD-PBA User’s Manual
Intel IGD Conguraon
GOP Driver
This item enable GOP Driver will unload VBIOS, disbale it will load VBIOS.
Opons: Enabled (Default) / Disabled
Integrated Graghics Device
This item enable/disable Integrated Graghics Device.
Opons: Enabled (Default) / Disabled
IGD Turbo Enable
This item select the IGD Turbo feature, if Auto selected, IGD Turbo will only be enabled when SOC
stepping is B0 or above.
Opons: Auto (Default) / Disabled / Enabled
GFX Boost
This item enable/disable GFX Boost.
Opons: Disabled (Default) / Enabled
DVMT Pre-Allocated
This item select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics
Device.
Opons: 32M (Default) / 64M / 96M / 128M / 160M / 192M / 224M / 256M / 288M / 320M / 352M /
384M / 416M / 448M / 480M / 512M
DVMT Total Gfx Mem
This item select DVMT 5.0 Total Graphic Memory size used by the Internal Graphics Device.
Opons: 256MB (Default) / 128MB / Max
Aperture Size
This item select the Aperture Size.
Opons: 256MB (Default) / 128MB / 512MB
GTT Size
This item select the GTT Size.
Opons: 4MB (Default) / 2MB / 8MB