Biostar DCS3A User manual

DCS3A Manual
1
D
DC CS S3 3A A M Ma an nu ua al l

DCS3A Manual
2
Table of Contents
Preface .................................................................................................3
Chapter 1: Introduction.........................................................................4
Chapter2: Hardware Installation ...........................................................5
Chapter3: Driver Installation.................................................................6

DCS3A Manual
3
Preface
Disclaimer
Information in this document has been carefully checked; however, no guarantee is given to
the correctness of the contents. No responsibility is assumed for its use or for any
infringement of patents or rights of third parties that may result from its use. No license is
granted by implication or otherwise under the patent rights. The information in this document
is subject to change without notice.
Copyright
ALL RIGHTS RESERVED.
This document contains proprietary information protected by copyright. No part of this
manual may be reproduced by any mechanical, electronic or other means, in any form,
without prior written permission.
Trademarks
Windows XP, Windows Vista, and Windows 7 are trademarks of Microsoft Corporation in the
US and other countries, used under license. All other trademarks are the property of their
respective o wners.
Conventions
The following conventions are followed throughout this manual:
Note: Text displayed in this manner indicates a note.
Prepare your working environment
Work Area: Make sure you have a stable, clean working environment with appropriate
lighting condition. Keep unused small components in containers to avoid lost.
Tools: The procedures that follow require several tools, including:
A cross-slot (Phillips) screwdriver
A grounding strap or an anti-static pad
Electrical and mechanical connections can be disconnected with your fingers. It is
recommended that not to use needle-nosed pliers when disconnecting connectors, since
needle nosed pliers may damage the soft parts of the connectors.
Precautions
Components and electronic circuit boards may be damaged by discharges of static electricity.
Working on a system that is connected to a power supply can be extremely dangerous.
Follow the guidelines below to avoid damage to the product or injury to yourself.
Always disconnect the unit from the power outlet before the operation.
If available, wear a grounded wrist strap. Or alternatively, discharge any static
electricity by touching the bare metal chassis of the unit case, or touch bare
metal body of any other grounded appliance.
Hold electronic circuit boards by the edges only. Do not touch the components
on the board unless it is necessary. Do not try to flex or stress circuit boards.
Keep all components inside the static-proof package which come with the
product before installation.
After installation is done, ensure that no screws or other small parts left inside
the case. Small metal parts can cause short circuits which may damage the
equipment.

DCS3A Manual
4
Chapter 1: Introduction
1.1 Features
1.2 System Requirements
The following operating systems are supported:
•Windows XP
•Windows Vista
•Windows 7
1.3 DCS3A Layout
LED1
SATA_CO NN2
SATA_CO NN1
SPEC
Form Factor
/ Siz e Standard ATX(full-height bracket) 79 x 58mm
Controller Asmedia ASM1061
Support 2 SATA3.0 devices
Support AHCI / NCQ
Int e rface PC I-E2.0 x1
Type SATA3 6Gbps / SATA2 3Gbps/ SATA 1.5Gbps

DCS3A Manual
5
Chapter2: Hardware Installation
Please follow the steps below to install your DCS3A card:
1. Shut down the computer and remove the case cover.
2. Remove the blanking plate from the PCI-Express.
3. Press DCS3A card firmly into the PCI-Express slot, making sure it is
properly seated.
4. Secure the card in place with a screw.
5. Connect to SATA devices.
6. Replace the computer case cover.
7. Turn on the computer and install the driver (Please refer to the Driver
Installation in this manual).

DCS3A Manual
6
Chapter3: Driver Installation
Note: The screenshots in this manual are for reference only.
Please follow the instructions in this section to install the driver for your
DCS3A card.
Insert the Setup CD into the optical
drive in your system. The program
should automatically display the
screen.
Click on Asmedia 106x SATA Host
Controller Driver to start the process
of driver installation.
The installation program will launc h
InstallShield Wizard. Click [Next]
and the program will begin to install
driver to your system.

DCS3A Manual
7
Note: When installing Windows XP on the HDD connected to DCS3A card, you
need a floppy drive in your system. As to the driver files, you may use other
computer to launch installation program firstly, and click on F6 floppy Asmedia
106x SATA Host Controller Drive to copy the files to your floppy disk. When
Windows XP Setup program shows “Press F6 to load SCSI/Raid Drivers” prompt,
please press F6 to install DCS3A driver.
Click [Yes] and the program will
begin to copy driver files to your
floppy disk.
2011/2/14