Bison BA803 User manual

1
P A R T S L I S T
Item Qty Description Item Qty Description
A 1 BASE K 4 5/16” HEX NUT
B 1H-FRAME L 2 3/8” X 3” HEX BOLT
C 1 REAR SUPPORT M 6 3/8” FLAT WASHER
D 2 ADJUSTABLE POLE N 6 3/8” LOCK WASHER
E 1 BACKBOARD (BA600) O 1 BACKBOARD SUPPORT PLATE
F 1 RIM (BA26) P 8 3/8” HEX NUT
G 2 WHEEL Q 2 1/4” LOCKING SPRING PIN
H 4 5/16” X 3 1/2” CARRIAGE BOLT R 6 3/8”-16 X 2-1/2” HEX BOLT
I 4 5/16” FLAT WASHER S 1 PADDING (BA803PP)
J 4 5/16” LOCK WASHER
 Inspect all contents prior to installation. Report any missing parts to dealer immediately.
 Read all instructions before proceeding.
—— Instruction Manual ——
BA803
Elementary Basketball Standard
Date: 10/08/15 Rev: 4 B.A. N.J.C. File: \INSTRUCTIONS\BA803INS Ref#:930366
Customer Service
[phone]
1. Attach Wheels (G) to Base (A) with 3/8” X 3” Hex Bolts (L), 3/8” Flat Washers (M), 3/8” Lock
Washers (N) and 3/8” Hex Nuts (P). See Figure 1.
2. Position the H-Frame (B) and Rear Support (C) in the gussets on Base (A). Install Rear Support (C) into
the short tube on H-Frame (B) with 3/8” X 2 1/2” Hex Bolt (R), 3/8” Flat Washer (M), 3/8” Lock
Washer (N) and 3/8” Hex Nut (P). Attach H-Frame (B) and Rear Support (C) with 3/8” X 2 1/2” Hex
Bolts (R), 3/8” Flat Washers (M), 3/8” Lock Washers (N) and 3/8” Hex Nuts (P). See Figure 1.
3. IMPORTANT! Please install a 3/8” X 2 1/2 Hex Bolt (R) and 3/8” Hex Nut (P) in the 2 places shown
in figure #1. These bolts are intended to provide a positive stop for the backboard assembly. See Figure 1.
4. Insert Adjustable Poles (D) into the H-Frame (B). Orient the Adjustable Poles (D) so the “top” 2 holes
spaced 15 1/2” apart are up to mount Backboard (E) using the 5/16” X 3 1/2” Carriage Bolts (H), 5/16”
Flat Washers (I), 5/16” Lock Washers (J) and 5/16” Hex Nuts (K). The square shoulders of the 5/16” X 3
1/2” Carriage Bolts (H) must be seated in the square holes in Backboard (E) before tightening the
hardware. See Figure 1 and 2.
5. Mount Rim (F) and Backboard Support Plate (O) to the backboard assembly as shown using the hardware
included with Rim (F). See Figure 1.
6. Install the net.
7. Install Padding (S) to the front uprights of the H-frame (B) toward the playing area. See Figure 1.

2
Warning!!!
The unit must be lowered to the 6 1/2’ position for transport. Failure to do so may result in injury!!
Do not leave outside as wind may cause tip over.
This system is not suitable for any player contact with the rim.
Rim Height Adjustment:
To raise and lower rim height ALWAYS tip the entire unit to the rear and rest parallel to the floor.
Remove Locking Spring Pin (Q) from each Adjustable Pole (D) and raise or lower the rim to the desired
rim height. Replace both Locking Spring Pins (Q) prior to returning to the playing position.
15 1/2" Backboard Mount Holes
Rim Height Adjustment Holes
6 1/2'
7'
7 1/2'
8'
MN P
G
L
IJK O
H
Q
MNP
F
S
P
R
D
E
Read Instruction #3
A
C
B
FIGURE 2
FIGURE 1
Note: Some hardware not shown for Illustration clarity.