Bissell 1692 PowerSteamer Clearview User manual

Safety Instructions
Product view
Assembly
Operations / Special Tools
PowerSteamer®
USER’S GUIDE
1692 POWERSTEAMER®CLEARVIEW®
1693 POWERSTEAMER®
1694 POWERSTEAMER®DELUXE
3
4
5
6-12
Routine Maintenance
13-16
Troubleshooting
17-18
Warranty
20
Replacement Parts
19
Consumer Services
18

Thanks for buying a BISSELL PowerSteamer Deep Cleaner
We’re glad you purchased a BISSELL PowerSteamer Deep Cleaner.
Everything we know about floor care went into the design and construction
of this complete, high-tech home cleaning system.
Your PowerSteamer is well made, and we back it with a limited
one-year warranty.We also stand behind it with a knowledgeable,dedicated
Consumer Services department, so,should you ever have a problem, you’ll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876.Today,
BISSELL is a global leader in the design, manufacture, and service of high
quality homecare products like your PowerSteamer.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2

3
IMPORTANT SAFETY INSTRUCTIONS
■Use only manufacturer’s recommended
attachments.
■Use only cleaning products formulated by
BISSELL for use in this appliance.
■Keep openings free of dust, lint, hair, etc.
■Keep appliance on a level surface.
■Turn off all controls before unplugging.
■Be extra careful when cleaning stairs.
■Close attention is necessary when used by
or near children.
SAVE THESE INSTRUCTIONS.
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
Commercial use of this unit voids the
manufacturer’s warranty.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded
wiring system.If it should malfunction or break
down,grounding provides a safe path of least
resistance for electrical current,reducing the risk
of electrical shock.The cord for this appliance
has an equipment-grounding conductor and a
grounding plug.It must only be plugged into an
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING:Improper connection
of the equipment-grounding conductor can
result in a risk of electrical shock. Check
with a qualified electrician or service person
if you aren’t sure if the outlet is properly
grounded. DO NOT MODIFY THE PLUG. If
it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
This appliance is designed for use on a
nominal 120-volt circuit, and has a
grounding attachment plug that looks like
the plug in the drawing above. Make cer-
tain that the appliance is connected to an
outlet having the same configuration as
the plug. No plug adapter should be used
with this appliance.
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all instructions before using your
POWERSTEAMER®.
WARNING:To reduce the risk of
fire, electric shock, or injury:
■Do not immerse.
■Use only on surfaces moistened by
cleaning process.
■Always connect to a properly grounded outlet
See Grounding Instructions.
■Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
■Do not leave machine when it is plugged in.
■Do not service machine when it is plugged in.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped in to water, have it repaired at an
authorized Service Center.
■Do not expose to rain, store indoors.
■Do not pull or carry by cord, use cord as a
handle,close door on cord,pull cord around
sharp corners or edges,run appliance over
cord,or expose cord to heated surfaces.
■Do not carry the appliance while in use.
■Do not unplug by pulling on cord. Unplug by
grasping the plug,not the cord.
■Do not handle plug or appliance with wet hands.
■Do not put any object into appliance openings,
use with blocked opening,or restrict air flow.
■Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts.
■Do not pick up hot or burning objects.
■Donot pick upflammableor combustible materials
(lighterfluid,gasoline,kerosene,etc.)or use inthe
presenceof explosive liquidsorvapor.
■Donotuseappliancein an enclosed space filled
withvaporsgivenoffby oil base paint,paint thinner,
somemothproofingsubstances,flammabledust,
orotherexplosiveortoxic vapors.
■Do not pick up toxic material (chlorine bleach,
ammonia,drain cleaner,gasoline, etc.).
■Do not modify the 3-prong grounded plug.
■Do not allow to be used as a toy.
■Do not use for any purpose other than
described in this User’s Guide.
■Do not operate the appliance unless the belt door
is securely assembled in the location provided.
Grounded
Outlets
Grounding Pin

4
DirtLifter®PowerBrush*
*(select models only)
Spray
Trigger
Easy Rolling
Wheels
ReadyTools™
Dial
WARNING:
To reduce the risk of fire,
use only BISSELLAdvanced Deep
Cleaning Formulas in
your PowerSteamer. Use of clean-
ing formulas that
contain lemon or pine
oil may damage this
appliance and void warranty.
Chemical spot cleaners or sol-
vent-based soil removers should
not be used.These products may
react with the plastic materials
used in your PowerSteamer caus-
ing cracking or pitting.
Power Cord
Belt Access
Door
Floor Nozzle
Window
Power
Switch
Flex Hose
Measuring
Cup
Handle
Release
Tank-in-Tank™
Quick Release
Cord Wrap™
Lower Cord
Wrap
Strain Reliever
Handle™
Handle
Assembly
Lower Body

5
How To Assemble Your PowerSteamer
How to Use This Guide
This User’s Guide is designed to help you get maximum
satisfaction from your PowerSteamer Deep Cleaner. Enclosed you’ll
find assembly instructions for cleaning tasks,safety precautions,
cleaning tips,maintenance and troubleshooting information. Please
read this guide thoroughly before assembling and using your cleaner.
Pay particular attention to the assembly diagram,assembly instruc-
tions,and part names. Locate and organize all parts before assembly.
Familiarize yourself with all parts and features and how they operate.
Following the Guide will enhance your ability to get top performance
from your cleaner for many years.
If you have any questions, or comments please call
BISSELL Consumer Services at 1-800-237-7691.
Your PowerSteamer assembles in two quick steps.The only
tool you will need to assemble your cleaner is a Phillips
head screwdriver.
Your PowerSteamer is packaged as two primary components… the
Lower Body and the Handle Assembly.To assemble:
Slide the Handle Assembly (with attached Quick Release
Cord Wrap™) down into the Lower Body until it will go
no further.
Secure the handle by placing one (1) Phillips head
screw (supplied) through the screw opening in the Lower
Body and into the rear of the Handle Assembly. Tighten with
screwdriver until secure.
Assembly is now complete.
Keep plenty of BISSELLAdvanced Deep Cleaning Formulas on hand so
you can clean whenever it fits your schedule.Always use BISSELL deep
cleaning formulas.Non-BISSELL cleaning solutions may harm your
cleaner and void the warranty.
1.
2.
Phillips
Head
Screw
What Comes With Your PowerSteamer
T
O
U
G
H
S
T
A
I
N
P
R
E
C
L
E
A
N
E
R
™
P
e
n
e
t
r
a
t
e
s
a
n
d
L
o
o
s
e
n
s
T
o
u
g
h
S
t
a
i
n
s
&
E
m
b
e
d
d
e
d
D
i
r
t
b
e
f
o
r
e D
e
e
p
C
l
e
a
n
i
n
g
PUSH
Tough Stain Brush Tough Stain Precleaner™ 16 oz. Fiber Cleansing
Formula™ with
Scotchgard protection

6
The Basics: How Your PowerSteamer Works
Tip:
Deep cleaning
carpeting and
upholstery regularly
can reduce dust
and allergens in
your home.
Power
The Power Switch controls power to the machine.
The powered brush roll at the Floor Nozzle is designed to enhance
cleaning performance.The bristle pattern lifts out the deep down
dirt while gently grooming carpet fibers.The floating suspension
self-adjusts to all carpet heights and protects your carpet if you
leave the Power Switch ON.When the machine handle is in the
fully upright position,CarpetSaver™automatically raises the brush
off the carpet.
Your PowerSteamer is equipped with a Measuring Cup for adding
the proper amount of cleaning formula to
theTank-in-Tank™.Before using the machine,simply
fill the Measuring Cup to the fill line with BISSELL
Advanced Deep Cleaning Formula.Pour the formula into theTank-
in-Tank as shown on page 7.For convenience,the Measuring Cup
stores on the back of the unit.
DirtLifter®Powerbrush (on select models)
Measuring Cup WARNING:
To reduce the risk of fire,
electric shock or injury
unplug from
outlet before servicing.
OFF
ON
ON
OFF
Power
Switch

This easy-to-use system is designed with a bladder inside to
hold clean water.As you clean,the bladder will empty. Dirty water
collects in the tank outside the bladder.
NOTE: Make sure to add formula to the tank
before filling it with water.
Depress the Handle Release pedal to tilt back
the handle.
Lift theTank-in-Tank handle.The handle locks the lid in
place.Carry the Tank-in-Tank like a bucket to fill at the sink.
Set the Tank down and rotate the handle forward to
unlatch the Lid. Lift off and set the Lid aside.
Using the Measuring Cup, pour BISSELL Deep Cleaning
Formula into the mouth of the bladder.
Fill to the bottom of the neck with hot tap water. Do not
boil or microwave water.
NOTE: Fill slowly to reduce sudsing.
Replace the Tank Lid, matching the Lid and Tank edges.
Rotate the handle to carrying position. ReplaceTank in
machine base, seating firmly in place. Rotate handle
back down to latched position.
7
To Fill The Tank-in-Tank
1.
2.
3.
4.
5.
Tilt Handle
Back
Handle
Release
Lift and
Carry
Rotate Handle to
Unlatch
1
2
3
6
6.
4
5

8
When It’s Time To Empty The Tank-in-Tank
NOTE: Remove the Tank-in-Tank, following steps 1.
and 2. on page 7.
Carry the Tank-in-Tank, like a bucket, to the sink. Remove
Tank Lid. Pour out dirty water.
After each use, remove and rinse the Lint Screen located
on the Tank Lid.
Remove Tank Lid.
Remove Lint Screen and rinse under faucet.
Remove any debris caught in Lint Screen.
Reinsert Lint Screen on Tank Lid.The screen will
click into place.
Replace Tank Lid.
Refill with cleaning solution and clean tap water—follow
steps 2-5. on page 7.
When a cleaning job is complete, rinse out the Tank-in-Tank
by running clean water between the bladder and the tank.
Return the Tank-in-Tank to the machine, follow step 6 on
page 7.
Refer to the Storage section on page 13 for final cleanup.
1.
2.
A.
4.
3.
5.
B.
C.
D.
Tip:
A special red float device in the
tank will cause the cleaner to
stop removing solution from the
carpet.The motor sound will rise
in pitch to let you know the dirty
water tank is full.
Lint Screen
Latched
1
2
5
6.

This provides floor or upholstery cleaning with the turn of a dial.For
carpet/floor cleaning make sure the dial is set to FLOOR CLEANING.
For upholstery or fabric cleaning,select your cleaning tool,attach it to
the Flex Hose,switch to Tools Settings and the PowerSteamer is
ready to clean upholstery, fabrics and more*
*Set the switch to FLOOR CLEANING when cleaning
carpets, or set it to TOOLS/PRETREAT when using
the Flex Hose attachments.
Plan activities to give carpet time to dry.
Remove easily moved furniture from the room (chairs,
lamps, coffee tables, etc.).
Vacuum thoroughly to pick up loose debris and pet hair
before using the PowerSteamer.
Plan your cleaning route to leave an exit path. It is best to
begin cleaning in the corner farthest from your exit.
NOTE: You may notice hair and debris deposits on
carpet that were loosened by brushing action
(especially with newer carpets that have never
been deep cleaned before). This debris should be
picked up by hand and thrown away. Debris that
deposits in the Brush Belt area should be cleaned
out to keep Belts running free.
Improves cleaning effectiveness for heavily soiled carpet in high
traffic areas,such as entryways and hallways.
Set the ReadyTools Dial to TOOLS/PRETREAT.
Plug the PowerSteamer into a proper outlet and turn ON the
Power switch.
While pressing the Spray Release trigger, slowly make sev-
eral passes over the area to be cleaned.
Caution: Do not overwet.
Turn the machine Power Switch OFF and let the
BISSELL Advanced Deep Cleaning Formula
dissolve the tough soil for 1 to 2 minutes. Reset the
ReadyTools Dial to FLOOR CLEANING
before continuing.
How To Clean Carpets
1.
2.
3.
4.
9
ReadyTools™Dial
2
4'
3'
1
3
4
5
6
7
9
10
11
12
EXIT
START
HERE
TOOLS
PRETREAT
FLOOR
CLEANING
Pretreating
1.
2.
3.
4.

10
Normal Cleaning
Plug the PowerSteamer into a proper outlet and turn ON the
Power Switch.
While pressing the Spray Release Trigger, make one slow
forward and back wet pass. Let the BISSELL Advanced
Deep Cleaning Formula and DirtLifter PowerBrush* do the
work for you.
*On select models
Caution: Do not overwet.
Release the Trigger and make one slow forward and back
pass over the same area to remove any residual dirty water.
Repeat cleaning passes without pressing the Trigger until
you can’t see any more water being suctioned up.
When cleaning job is complete, refer to the
Maintenance/Storage section on page 13.
The Bare Floor Tool (available with select models
only) provides effective cleaning for linoleum, vinyl,
and tile floors.
Caution: Do not use on hardwood floors
Use BISSELL Floor Cleansing Formula.
Vacuum or sweep thoroughly to pick up loose debris and
pet hair.
Remove easily moved furniture from the room,(chairs,
tables,etc.)
Plan your cleaning route to leave an exit path.
Plan activities to allow 30 minutes for the floor to
dry completely.
1.
2.
3.
4.
5.
Tip:
Thorough
vacuuming before
deep cleaning will
prevent early
clogging of the
lint trap.
Cleaning Bare Floors
1.
2.
3.
4.
5.

11
Step on the handle release to lay the machine handle down.
Remove the Tank-in Tank from the machine base.
Lift the machine base to expose the underside of the nozzle.
Attach Bare Floor Tool to nozzle with long tab to the right side
(ReadyTools side) of the nozzle.
First attach left side (short Tab) catching tab over nozzle edge.
Gently bend long tab (right side) outward to easily snap over
edge of clear nozzle on left.
Set up machine following instructions in The Basics on pages
6-9. Be sure to thoroughly rinse out any remaining Fiber
Cleansing Formula from the Tank-in-Tank bottle to prevent
slippery linoleum, vinyl,and tile floors. Use BISSELL Floor
Cleansing Formula in the Tank-in-Tank.
Check ReadyTools dial - it should be set on FLOOR CLEANING.
Plug into a proper outlet and turn Power Switch ON.
Slowly move the machine nozzle with Bare Floor Tool
forward and back over soiled surface one time while
pressing the trigger. Caution: Do not over wet.
Repeat the motion without pressing the trigger using the Bare
Floor Tool to squeegee and suction up the dirty water.
Repeat steps 1 and 2 backing along the exit path.
Allow about 30 minutes for the floor to dry completely.
When the cleaning job is complete refer to the
Maintenance/Storage section on page 13.
To remove Bare Floor Tool gently bend long tab (right side)
outward and pull tool down away from nozzle. Rinse
thoroughly, dry and store.
6.
Machine Preparation
1.
2.
3.
Attach the Bare Floor Tool
1.
2.
3.
4.
5.
Bare Floor
Cleaning Tool Snap Together
Bottom Front Edge of
Machine Base
Tilt
Handle
Back
Handle Release
Carrying
Bare Floor Cleaning Technique
1.
2.
3.
4.
5.
6.
WARNING:
To reduce the risk of fire,
electric shock or injury
unplug from outlet
before servicing.

Check manufacturer’s tag before cleaning.A "W" or "WS" on
the tag means you can use your PowerSteamer. If the tag is
coded with an "X" or "S" (with a diagonal strike through), or
says "Dry Clean Only," do not proceed. Do not use your
PowerSteamer on velvet or silk. If manufacturer’s tag is
missing or not coded, check with your furniture dealer.
Check for colorfastness in an inconspicuous place.
If possible, check upholstery stuffing. Colored stuffing may
bleed through fabric when wet.
Plan activities to give upholstery time to dry.
Vacuum thoroughly to pick up loose debris and pet hair.Use a
vacuum with a brush attachment and a crevice tool to clean in
fabric folds and tufts.
Set up the machine following instructions in The Basics sec-
tion, pages 6-9.
Using the Measuring Cup provided, pour BISSELL Advanced
Deep Cleaning Formula into the Tank-in-Tank.
Set the ReadyTools Dial to TOOLS/PRETREAT.
12
How To Clean Upholstery and Small Areas
Adsdfddghgbvh
cvbbjjknhnbj jkvh
gcghhjj jhffhl kllgh
Important - Check Upholstery Tags
Machine Preparation
1.
2.
3.
Manufacturer’s
Tag

13
Maintenance/Storage
Turn Power Switch OFF.
Unplug Power Cord from outlet and coil cord
around Power Cord Quick Release.
Remove and rinse tools, if used, in clean, running
water. Dry and replace.
Coil Flex Hose through storage brackets.
Remove Tank-in-Tank. Dispose of dirty water. See
The Basics section, page 8.
Rinse out Tank-in-Tank and reseat the tank unto
the machine.
Wipe all exterior surfaces with a soft cloth.
Store cleaner in a protected, dry area.
When carpet is dry, vacuum again to remove
hair and fuzz that the PowerSteamer may
have loosened.
NOTE: Turn off machine and unplug from
wall outlet.
Step on Handle Release pedal and recline Handle
on floor (see illustration).
Remove theTank-in-Tank.Set aside (see illustration).
Remove the Belt Access Door located near the
ReadyTools Dial. Insert a flathead screwdriver into
the slot nearest the handle to gently pry off the
door (see illustration).
1.
3.
4.
2.
5.
6.
7.
8.
9.
CAUTION:
PowerSteamer®uses water
and must not be stored
where there is a danger of
freezing. Freezing will
damage internal components
and void the warranty.
Pump & Brush Belts Replacement
To Remove Broken Pump & Brush Belts
1.
2.
3.
Power Cord
Quick Release
Flex Hose
Storage Bracket
1
2
3

14
To Remove Broken Pump & Brush Belts-Continued
Turn the machine onto its side so the belt access area is
facing upward (see illustrations).
On the bottom of the machine, near the belt access area, is
a Red Retainer Plate that holds the black brush arm and
brush in place. Using a Phillips head screwdriver remove
the screw that holds the Red Retainer Plate in place. Set
Red Retainer Plate and Phillips head screw aside
(see illustrations).
NOTE: For 1693 Model Series, remove stationary
brush (skip step 6 and 7).
Remove the black brush arm that holds the brush in place.
Set the black brush arm aside
(see illustrations).
Remove the "toothed" Brush Belt from the Brush then from
the Red Pump Pulley. Set the "toothed" Brush Belt and
Brush aside.
Locate and remove the broken Pump Belt.
4.
5
6.
7.
8.
5
4
6
7
8
Red Retainer
Plate

15
To Install The Replacement Pump & Brush Belts
NOTE: For 1693 Model Series, skip steps 2 & 4.
With the unit still on its side, loop one end of the replacement
Pump Belt around the Red Pump
Pulley and the other end around the silver motor shaft (see illustra-
tion). Do not twist the replacement Pump Belt.
Re-install the “toothed” Brush Belt first onto the Red Pump Pulley
and then onto the “toothed” end of the Brush (see illustrations).
Re-install the Brush into the base of the unit.
Place the black brush arm onto the Brush and slide black brush
arm into original position (see illustrations).
1.
2.
3.
4.
2
1
3
4

16
To Install The Replacement Pump & Brush Belts-Continued
Re-install the Red Retainer Plate and Phillips head screw
(see illustration).
Using your finger, gently spin the replacement Pump Belt
on the silver motor shaft (see illustration). If assembled
correctly, the replacement Pump Belt should rotate freely
around the silver motor shaft and drive pulley without
obstruction.The Brush should also rotate freely when the
silver motor shaft is turned.
Turn the machine right side up. Replace theTank-in-Tank
and Belt Access Door (see illustration).
Assembly is now complete.
If you have any questions, or if you have any trouble
installing your replacement Pump Belt, please call BISSELL
Consumer Services
at 1-800-237-7691.
Or visit the BISSELL website:www.bissell.com
5.
6.
7.
5
6
7
Red Retainer
Plate
Belt Access
Door

17
WARNING:
To reduce the risk of fire,
electric shock, or injury,
unplug machine from
outlet before servicing.
Reduced spray or no spray.
Possible Causes Remedies
Bladder may be empty Refill tank with hot tap water.
The lint screen may be clogged Clean out lint screen page 8.
Tank-in-Tank may not be seated properly Turn power off; remove and reseat tank.
Pump may have lost prime. Turn power OFF; after 1 minute, turn
ON and depress Spray Release trigger.
The Pump Belt may be broken. Turn power OFF and unplug machine
from outlet.To check if a Pump Belt
has broken, you will need a flathead
screwdriver. Insert the blade
end into the lower slot of the Belt
Access Door to release the lower snap.
If necessary, insert the blade end into
the upper slot to release the upper
snap. Examine for belt breakage.You
should be able to see the Pump Belt
looped around the motor shaft. If it is
broken or missing, please refer to the
Part numbers and descriptions on
page 19 before calling BISSELL
Consumer Services. Complete
installation instructions will accompany
the replacement belt.
DirtLifter PowerBrush* does not turn.
Possible Causes Remedies
The Brush Belt or Pump Belt Turn power OFF and unplug machine
may be broken from outlet.To check if a Brush Belt
has broken, you will need a flathead
screwdriver. Insert the blade
end into the lower slot of the Belt
Access Door to release the lower snap.
If necessary, insert the blade end into
the upper slot to release the upper
snap. Examine for belt breakage. If
broken, refer to pages 13-16.
Troubleshooting
Lift Here
Insert Screwdriver
Blade Here
*On select models only

18
Troubleshooting-continued
PowerSteamer not picking up solution.
Possible Causes Remedies
ReadyTools Dial may be at the Set ReadyTools Dial to either FLOOR
wrong setting for cleaning job. CLEANING or TOOLS/PRETREAT.
Nozzle Window may not be Make sure the two tabs on the back of
properly attached. the Nozzle Window are inserted
through the mating slots in the main
housing. Reinstall if necessary.
Tank-in-Tank lid is not Reinstall lid; refer to The Basics
properly installed. section, page 7.
Tank-in-Tank is not properly seated. Tank-in-Tank must be firmly seated to
function.Remove and reseat Tank-in Tank.
Tank-in-Tank has picked up the maximum Empty tank and refill; refer to
amount of dirty water. Basics section, page 8.
Poor tool position. Readjust angle; apply more downward
(Handheld attachments only.) pressure.
Thank you for selecting a BISSELL product.
If you should happen to need assistance during assembly or operation, call: 1-800-237-7691
Please do not return this
product to the store.
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 9 p.m. EST
Saturday 9 a.m. — 5 p.m. EST
Or write:
BISSELL INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
BISSELL Consumer Services
©2002 BISSELL Inc
Grand Rapids, Michigan
All rights reserved. Printed in USA.
Part Number 310-5800
Rev 3/02
Visit our website at:
www.bissell.com
Scotchgard a trademark of 3M

19
Part Numbers And Descriptions*
*Not all parts included with every model
Item Part No. Part Name
1 603-7818 Handle Assembly with Screw
2 215-9155 Tough Stain Brush
3 015-9043 Tank Assembly Complete
4 015-4439 Tank Lid Assembly
5 015-9041 Tank Bottom
6 213-0213 Baffle with Red Float
7 210-4052 Window Gasket
8 015-0628 Replacement Pump Belt (with instructions)
9 015-0621 Replacement Brush Belt (with instructions)
10 015-3500 Lint Screen
11 213-3010 Measuring Cup
12 214-9131 Bare Floor Tool
13 0710 48 oz. BISSELL Fiber Cleansing Formula with Scotchgard™
14 0400 22 oz. BISSELL Tough Stain PreCleaner
15 0480 32 oz. BISSELL Floor Cleansing Formula
PUSH
13
T
O
U
G
H
S
T
A
I
N
P
R
E
C
L
E
A
N
E
R
™
P
e
n
e
t
r
a
t
e
s
a
n
d
L
o
o
s
e
n
s
T
o
u
g
h
S
t
a
i
n
s
&
E
m
b
e
d
d
e
d
D
i
r
t
b
e
f
o
r
e D
e
e
p
C
l
e
a
n
i
n
g
14
Floor Cleansing Formula
FOR DEEP
CLEANING MACHINES
™
32FL.OZ.
(946mL)
CAUTION:MAYBE IRRITATINGTO THEEYES. READBACK PANELCAREFULLY
Safely Deep Cleans and
Revitalizes No-Wax Floors
D
I
R
T
A
N
D
S
T
A
I
N
S
R
E
M
O
V
E
S
D
E
E
P
D
O
W
N
®
1512
11
9
87
6
4
32
1
10
5

20
About Your Warranty
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state. If you need additional instruction regarding this warranty
or have questions regarding what it may cover, please contact BISSELL Consumer
Services by E-mail, telephone,or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the
product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge from the date of
purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal,and not commercial or rental service.This
warranty does not apply to fans or routine maintenance components such as filters,belts, or
brushes.Damage or malfunction caused by negligence, abuse,neglect, unauthorized repair, or
any other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELLAuthorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty,contact
BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the“Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m.- 9 p.m. EST
Saturday 9 a.m. - 5 p.m.EST
Or write:
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN:Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITHTHE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVEAND IN LIEU OF ANY OTHERWARRANTIES EITHER ORAL OR WRITTEN.
ANY IMPLIED WARRANTIESWHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO
THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBEDABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.