Bissell POWERFORCE HELIX TURBO PET User manual

Product Overview
1. Upper Handle
2. Tank Release Button
3. Washable Pre-Motor Filter
4. Dirt Tank
5. Dirt Tank Empty Button
6. Washable Post-Motor Filter
7. Hose Clip
8. Power Cord
9. Lower Cord Wrap
10. Hose Wand
11. Power Switch Pedal
12. Handle Recline Pedal
13. Pet TurboBrush® Tool
POWERFORCE® HELIX™ TURBO PET
UPRIGHT VACUUM | 3332 SERIES
What’s In The Box?
Handle &
Body
2 Screws (taped
to Upper Handle)
Hose Lower Cord
Wrap
Dusting
Brush
Crevice
Tool
Extension
Wand
Pet TurboBrush®
Tool
Meet your new BISSELL product!
Go to support.BISSELL.com for a comprehensive walkthrough
of your new purchase, including videos, tips, support, and more.
Want to get started right away? This guide has all the information
you need to set up your new product. Let’s take a look…
9
10
1
2
3
4
11
12
56
7
8
13

2BISSELL.com
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
•Do not leave vacuum when it is plugged in. Unplug from outlet when
not in use and before servicing.
•Do not use outdoors or on wet surfaces.
•Do not allow to be used as a toy. Close attention is necessary when
used by or near children.
•Do not use for any purpose other than described in this user guide.
Use only manufacturer’s recommended attachments.
•Do not use with damaged cord or plug. If appliance is not working as
it should, has been dropped, damaged, left outdoors, or dropped into
water, have it repaired at an authorized service center.
•Do not pull or carry by cord, use cord as a handle, close a door on
cord, or pull cord around sharp edges or corners. Do not run appliance
over cord. Keep cord away from heated surfaces.
•Do not unplug by pulling on cord. To unplug, grasp the plug,
not the cord.
•Do not handle plug or vacuum with wet hands.
•Do not put any object into openings. Do not use with any opening
blocked; keep openings free of dust, lint, hair, and anything that may
reduce air flow.
•Keep hair, loose clothing, fingers, and all parts of body away from
openings and moving parts.
•Turn OFF all controls before plugging or unplugging vacuum.
•Use extra care when cleaning on stairs.
•Do not use to pick up flammable or combustible materials (lighter
fluid, gasoline, kerosene, etc.) or use in areas where they may be
present.
•Do not use vacuum in an enclosed space filled with vapors given off
by oil-based paint, paint thinner, some moth-proofing substances,
flammable dust, or other explosive or toxic vapors.
•Do not use to pick up toxic material (chlorine bleach, ammonia, drain
cleaner, etc.).
•Do not pick up anything that is burning or smoking, such as cigarettes,
matches or hot ashes.
•Do not use without filters in place.
•Do not pick up hard or sharp objects such as glass, nails, screws,
coins, etc.
•Use only on dry, indoor surfaces.
•Keep appliance on a level surface.
•Do not carry the vacuum while it is running.
•Unplug before connecting or disconnecting the Pet TurboBrush® Tool.
THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk
of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a
proper outlet. Do not change the plug in any way.
Warranty
Limited 2-year warranty, may vary by state. Visit support.BISSELL.com or call 1-800-237-7691 for
complete warranty information.
For a comprehensive walkthrough of your product and support tips, visit support.BISSELL.com.
Troubleshooting
SAVE THESE INSTRUCTIONS
THIS MODEL IS FOR HOUSEHOLD USE ONLY. COMMERCIAL USE OF THIS UNIT VOIDS THE MANUFACTURER’S WARRANTY.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING Plastic film can be dangerous. To avoid danger of suocation, keep away from children.
• Do not plug in your vacuum until you are familiar with all instructions and operating procedures.
• To reduce the risk of electrical shock, turn power OFF and disconnect polarized plug from electrical outlet BEFORE performing
maintenance or troubleshooting checks.

BISSELL.com 3
1. Place upper handle onto
base and push down. Attach
handle using two screws taped
to the handle in a plastic bag.
2. Insert lower cord wrap and
turn counterclockwise to lock
it into place.
3. Wrap cord. To easily
unwrap, turn the Quick Release
Cord Wrap down.
4. Insert end of hose into back
of vacuum and twist to lock
into place.
5. Wrap hose through hose
clip and connect hose wand to
the foot hose at the bottom of
vacuum.
6. Attach desired tool.
The crevice tool is stored
inside the extension wand.
1. Turn ON ( ) vacuum using
power ( ) pedal and lean
back using recline pedal. When
finished, press pedal switch
again to turn OFF ( ). Return
to upright position.
2. Press handle recline pedal
to lean vacuum back. Press
pedal a second time to recline
further. When finished, lean
all the way up to lock it into
upright position.
3. Vacuum can be raised or
lowered to adjust to different
types of flooring. Turn knob
towards desired flooring type.
If vacuum becomes difficult to
push, move to a higher setting.
Using Your Vacuum
Assembly
1. Press the tank release button
and pull handle to lift dirt tank
away from vacuum.
2. Holding dirt tank over a trash bin, press release button on
back to open tank and dump debris.
Snap bottom back into place when empty.
Emptying the Dirt Tank

4
Maintaining Your Vacuum
For more helpful maintenance tips, check out support.BISSELL.com.
Replacing the Brush and Belt
1. Unplug vacuum, turn over and unscrew five
Phillips-head screws to remove bottom cover.
2. Lift brush roll straight out. Inspect belt and
replace if it appears damaged.
3. Replace brush roll and belt by looping the
belt over motor shaft and brush roll. Line up
the endcaps and pull brush forward into place,
stretching the belt. Replace cover and screws.
Clearing a Clog
1. Remove hose from back of vacuum by twisting
to the left. Remove debris.
2. Check foot hose on the back of vacuum
towards the bottom. If necessary, remove screw
from foot hose and check for clogs.
3. Check air passageway on bottom of vacuum.
Remove bottom cover and brush. Remove any
debris.
Maintaining the TurboEraser® Tool
1. Twist gray collar counterclockwise until slot
appears, separate faceplate and remove brush.
Replace belt and brush if needed.
2. If paddle wheel is dislodged, align the two
clips on each side and click into place.
3. The faceplate will not close if all parts are not
aligned correctly.
1. Remove dirt tank by
pressing release button and
lift tank away from vacuum.
2. With dirt tank removed,
press filter cover release
button to access post-motor
filter.
3. Clean filters with mild
detergent, rinsing and
squeezing to remove water.
Allow filters to dry completely
before reinserting.
4. To access pre-motor filter,
lift release latch on front
of tank to lift lid.
5. Remove pre-motor filter
from tank lid. Clean with
warm water and allow to dry
completely before reinserting.
6. Remove separator from tank
by twisting counterclockwise.
Pull out through the bottom.
Rinse and dry with a cloth.
Cleaning the Filters & Separator
©2023 BISSELL Inc. All rights reserved.
Part Number 1629452 11/22 RevC
Every Purchase Saves Pets™
BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets.
When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help
make pet messes, odors and pet homelessness disappear. Visit BISSELLsavespets.com to learn more.