Bissell Total Floors Pet 61C5 Series User manual

PPA1208J
AIRE ACONDICIONADO PORTATIL
PORTABLE AIR CONDITIONER

1
CONTENTS
IMPORTANT SAFEGUARDS…..................................................................2
PLACEMENTAND INSTALLATION….........................................................3
PARTS NAME…..........................................................................................5
CONTROL PANEL…...................................................................................6
SCREEN…...................................................................................................7
OPERATION METHODS…..........................................................................8
REMOTE CONTROL…...............................................................................9
WATER DRAINAGE….................................................................................9
MAINTENANCE….......................................................................................10
TROUBLE SHOOTING…............................................................................11
WIRING DIAGRAM …..................................................................................12

2
IMPORTANT SAFEGUARDS
Please read following safeguards carefully before using the machine:
●This machine just for domestic use, please don’t use it in any other places.
●Please use this machine indoor not outdoor, and place it in a dry environment.
●Don’t use the machine when any damage in power cord, plug or machine itself.
Any damage, please contact professional serviceman for help. If need to lengthen
power cord, extended cord can be used, but please don’t let the power cord scatter on
the work area.
●Please make the machine far from heat sources and power supply , and avoid direct
sunlight.
●Please turn-off the machine first before pull out the plug.
●Please pull out the plug when the machine is under cleaning, parts-replacement or leaving
unused.
●Please clean the machine based on the instruction in user’s manual.
●Please make sure using voltage meet requirements, the damages caused by
connection error is out of the scope of warranty.
●Don’t let little children touch the machine.
●Don’t run the machine when no one there, even if a short leave, please turn-off it.
●Don’t tug power cord when pulling out plug or moving the machine.
●Don’t put the machine on a place with water or other liquid.
●Don’t spatter water or oil into machine.
●Don’t put hard objects between fan blades.
●Don’t repair the machine by yourself. Dealing with problems by non-professional
person may cause danger, even power cord replacement must be done by professional
electrician.
●Only use accessories from suppliers, otherwise danger and damages of the machine
may be caused .

3
Note :
●Place the machine on flat ground, and keep it far from around things at least 50cm.
●Make sure the socket can be reached from machine location.
●Keep the machine stand upright so that compressor can work well.
●Don’t run the machine near to gasoline or any other flammable liquids.
●Make sure free access of air-inlet and air-outlet.
●Don’t use spraying agent (such as pesticides , paint) or other flammable materials,
otherwise
plastic deformation, or even electric damage of the machine may be caused.
Power supply
●Make sure no damage in plug.
●Don’t use connector instead of plug.
●Insert pug into socket first, then turn on socket switch , press key “POWER” to run
machine.
Please safekeep this user’s manual.
Placement and Installation
Placement
●Place the machine on flat and dry ground, and keep it far from around things at least 50cm.
(fig.1)
(fig.1)

4
Installation
●Spin adapter into exhaust pipe first, then spin the exhaust pipe into exhaust connector .
(fig.2)
●Put adapter into window sealplate, adjust window open width in order sealplate match
window well, and the length of sealplate is adjustable.
(fig.2)
Installation Errors
●Free access of exhaust pipe is important, installation errors will bring bad influence of
machine. (fig.3)
●Avoid exhaust-pipe with sharp bend.
●Make sure air in exhaust pipe can run smoothly .
(fig.3)
Warning
Length of exhaust pipe according to the machine features, please don’t replace or lengthen
it freely, otherwise errors will be easily caused.
Note: extreme length of unfolding exhaust pipe is 1500mm, please shorten the length as
much as possible and keep it level as much as possible when installing .

5
Parts Name
Front side
1. Air-inlet
2. Control Panel
3. Screen
4. Castor
Back Side
5. Filter frame upper
6. Power Cord Location
7. Filter frame lower
8. Plug cap
9. Exhaust Pipe
10. Handle
11. Exhaust Connector
Check packing accessories, read user’s manual to get how to use them.
(fig.4)
1. Exhaust Pipe 2. Sealplate 3. Adapter 4. Remote control

6
Control Panel
Timer Sleep Up DOWN Fan Mode Power
1. POWER: press this key to turn on/off machine. After machine turns on, default value is
cooling mode with low fan speed.
2. MODE: after machine turns on, for cooling only model, press this key to select cooling,
fan mode
3. FAN: after machine turns on, press this key to select fan speed (high ,medium and low).
4. DOWN: under cooling or heating mode, press this key to downward setting temperature
from 16~31℃; under timer mode, press this key to downward on/off time.
5. UP: under cooling or heating mode, press this key to upward temperature from 16~31℃;
under timer mode, press this key to upward on/off timer.
6. SLEEP: under cooling or heating mode, press this key to turn on/off sleeping function.
7. TIMER: under power-on or standby mode, press this key to setup on/off time from 0~24.

7
Screen
1. Temperature display
2. Cooling mode indicator
3. Dehumidifying mode indicator
4. Fan mode indicator
5. Sleeping mode indicator
6. Timer mode indicator
7. Receiver
8. Water full indicator
9. Low fan speed
10. Medium fan speed
11. High fan speed

8
Operation Methods
Cooling mode
●After machine turns on, default value is cooling mode with 22℃and low fan speed.
●Press “ MODE” to select cooling mode, cooling mode indictor turns on .
●Press “ UP” or “ DOWN” to adjust temperature ( from 16℃to 31℃).
●Press “ FAN” to select fan speed(low, medium ,high)
Fan mode
●Press “ MODE” to select fan mode, fan mode indicator turns on .
●Press “ FAN” to select fan speed(low, medium ,high)
●Temperature and sleeping function cannot be setup.
Timer mode
●Under standby mode, press “TIMER” to setup the power-on time, press “UP” and
“DOWN” to adjust the timer (from 1 to 24). Timer indicator turns on.
●Under power-on mode, press “TIMER” to setup power-off timer. Press “UP” and
“DOWN” to adjust the timer (from 1 to 24). Timer indicator turns on.
Sleeping mode
●Press key “SLEEP” enter into sleeping mode, default value of fan speed is low.
●When sleeping mode turns on , under cooling mode, the one hour later, setting
temperature will go up 1℃, the second one hour later, setting temperature will go up
another 1℃, and then keep the same ;under heating mode, the first one hour later,
setting temperature will go down 1℃, the second one hour later , the setting
temperature will go up another 1℃, and then keep the same .
●Sleeping mode is invalid under dehumidifying and fan mode. Under water full, machine
standby and mode conversion, sleeping mode will be cancelled .
Compressor protection
●Three minutes later after power on / restart, compressor starts to run.

9
Remote Control
1. Power 2. Timer 3. Down 4. Mode 5Up
6. Fan 7. Sleeping
Water Drainage
This machine with auto-water-evaporating system. Condensed-water
cycle to cool down the condenser, which will not only improve cooling
efficiency, but also save energy.
●If inner water tank is full, “ ” will flashed on the screen , 8 seconds later machine enter
into standby mode, buzzer shouts , compressor stops and all keys is invalid till machine
recovers to be normal .
●Pull out the plug to drain out water, power off the machine and restart it , the machine will runs
normally .