BITMAIN AntMiner S1 User manual

BITMAIN
AntMiner Manual

AntMiner Manual
Last updated: 11/26/2013
Page 2 of 9
Page 2 / 9
Contents
1 The first glance..........................................................................................................................3
2 Power Supply.............................................................................................................................4
3 Connect to Miner ......................................................................................................................4
3.1 WAN setting ..................................................................................................................4
3.2 WIFI setting ...................................................................................................................7
4 Pool Setting ...............................................................................................................................7
5 Miner Status..............................................................................................................................8
6 System Configuration ................................................................................................................9
6.1 Password Modification..................................................................................................9
6.2 System Upgrading .........................................................................................................9

AntMiner Manual
Last updated: 11/26/2013
Page 3 of 9
Page 3 / 9
1The first glance
AntMiner S1 is a blade style miner, which contains two blades. It has been assembled before Fab
out. Bellow screen shows all AntMiner S1’s components:
One blade miner can work separately, it is showed in bellow:
Notice:
1. You should prepare your own ATX Power Supply.
2. To connect your Miner via WIFI, you should prepare your own WIFI antenna.

AntMiner Manual
Last updated: 11/26/2013
Page 4 of 9
Page 4 / 9
2Power Supply
Connect the 12V Power line to the Power Supply socket. Note not to reverse positive (+12V) to
negative (GND).
3Connect to Miner
3.1 WAN setting
Step 1. Read the IP address labeled in the Fan Bracket (Front). Manually set up your PC’s IP
address in the network segment same as the miner’s IP address.

AntMiner Manual
Last updated: 11/26/2013
Page 5 of 9
Page 5 / 9
Step 2. Connect miner and your PC via network cable.
Step 3. Enter miner’s IP address into your web browser, then login miner management interface,
both of username and password is ‘root’ by default.
Setp 4. Set LAN as DHCP client. Click “Network->Interface->LAN”, select DHCP client as the
following page, and then click “Switch Protocol“, and then click ”Save & Apply”. The default LAN
value of the first several batch is fixed to 192.168.1.1, and WAN address can’t be set as
192.168.1.x, otherwise the AntMiner can’t be accessed. If your miner’s LAN is set as DHCP by
default, please ignore this step.

AntMiner Manual
Last updated: 11/26/2013
Page 6 of 9
Page 6 / 9
Step 5. Modify the IP address of the WAN interface. Click “Network->Interface->WAN” to modify
the IP address of WAN in the following page.
Note:
1. WAN and LAN can’t be at the same network segment. Please set WAN to DHCP client or
different network segment with WAN. The LAN of new version of antMiner will be set to
DHCP by default.
2. If you set fixed IP to WAN interface, please remember it, otherwise you may not access the
antminer.

AntMiner Manual
Last updated: 11/26/2013
Page 7 of 9
Page 7 / 9
3.2 WIFI setting
There is WIFI built in the antMiner, and it can be used to connect to the Ethernet via another
WIFI hot point. Note: Bad WIFI performance will reduce the antminer’s hash rate. You have to
prepare the WIFI antenna by yourself.
Through “Network->Wifi“you can click ”Scan“ and then add the exist WIFI signals in your
enviornment.
4Pool Setting
Through ‘Status->Miner Configuration ‘, you will be able to configure your miner.
Pool URL- you should enter the URL of your desired pool.
Worker- this is your worker ID on the selected pool.
Password- this is the password for your selected worker. In general password can be set casually.
Comment: AntMiner can set up three mine pools, the priority decreases from first pool (pool 1)
to third pool (pool 3). The low priority pool will start to work, only when the high priority pool
encounter fault.

AntMiner Manual
Last updated: 11/26/2013
Page 8 of 9
Page 8 / 9
5Miner Status
Through ‘Status->Miner Status‘, you will be able to check your miner running status.
ASIC#: ASIC number in the chain
Fan: Fan speed
Temp: Temperature, centigrade
Frequency: ASIC setting frequency
ASIC status: o stands for OK, x stands for error.

AntMiner Manual
Last updated: 11/26/2013
Page 9 of 9
Page 9 / 9
6System Configuration
6.1 Password Modification
Through ‘System->Administration’, you will be able to modify AntMiner login password, and
choose ‘Save’and ‘Save and Apply’after modifying it.
6.2 System Upgrading
Through ‘System->Backup / Flash Firmware’you will be able to upgrade your miner.
‘Keep setting’is chosen by default, you should choose it if you hope to preserve the current
settings. You should cancel this option if you hope to restore to initial settings.
Click ‘Browse’button to choose upgrade file. After choosing upgrade file, then click ’Flash image...’
button to start downloading this file to your system. After downloading, please click ‘Proceed’
button, then upgrade system. During the upgrade process, you need to wait patiently, and must
keep power on, otherwise, AntMiner will restore to initial settings. AntMiner will be connected
to login interface after finishing system upgrade.