Black & Decker KG750 User manual

KG750
KG751
www.blackanddecker.ae

ENGLISH
2
3
42
1

3
ENGLISH
B
A
D
C
48
9
510 11 13 5 10 11 13
14
13
11
9
7
6
13
11
12
10
5
5

4
ENGLISH
E
13
16
15
10
5

5
ENGLISH
Intended use
Your Black & Decker angle grinder has been
designed for grinding and cutting metal and
masonry using the appropriate type of cutting or
grinding disc. When fitted with the appropriate
guard, this tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions listed below
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference. The term "power tool" in all of the
warnings listed below refers to your mains
operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.Amoment of inattention while
operating power tools may result in serious
personal injury.
b. Use personal protective equipment.Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.

6
ENGLISH
d. Remove any adjusting key or wrench before
turning the power tool on.Awrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off.Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk
of starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional power tool safety
warnings
Warning!Additional safety warnings
for grinding, sanding, wire brushing,
polishing or abrasive cutting-off
operations
•This power tool is intended to function as a
grinder, sander, wire brush, polisher or cut-off
tool. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
•Operations for which the power tool was not
designed may create a hazard and cause
personal injury.

7
ENGLISH
•Do not use accessories which are not
specifically designed and recommended by
the tool manufacturer. Just because the
accessory can be attached to your power
tool, it does not assure safe operation.
•The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool.Accessories running faster
than their rated speed can break and fly
apart.
•The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded
or controlled.
•The arbour size of wheels, flanges, backing
pads or any other accessory must properly fit
the spindle of the power tool.Accessories
with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
•Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect
for damage or install an undamaged
accessory.After inspecting and installing an
accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break
apart during this test time.
•Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses.As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of filtering
particles generated by your operation.
Prolonged exposure to high intensity noise
may cause hearing loss.
•Keep bystanders a safe distance away from
work area.Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
•Hold power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live"
and shock the operator.
•Position the cord clear of the spinning
accessory. If you lose control, the cord may
be cut or snagged and your hand or arm may
be pulled into the spinning accessory.
•Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
•Do not run the power tool while carrying it at
your side.Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
•Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the
housing and excessive accumulation of
powdered metal may cause electrical
hazards.

8
ENGLISH
•Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
•Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
Note: The above warning does not apply for
power tools specifically designed for use with a
liquid system.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the
accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel's movement at the point of
pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below.
•Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces.Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are
taken.
•Never place your hand near the rotating
accessory.Accessory may kickback over your
hand.
•Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction
opposite to the wheel's movement at the point
of snagging.
•Use special care when working corners,
sharp edges etc.Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag
the rotating accessory and cause loss of
control or kickback.
•Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety warnings specific for
grinding and abrasive
cutting-off operations
•Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed
cannot be adequately guarded and are
unsafe.
•The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator.The guard
helps to protect operator from broken wheel
fragments and accidental contact with wheel.
•Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel.Abrasive cut-off
wheels are intended for peripheral grinding,
side forces applied to these wheels may
cause them to shatter.

9
ENGLISH
•Always use undamaged wheel flanges that
are of correct size and shape for your
selected wheel. Proper wheel flanges
support the wheel thus reducing the
possibility of wheel breakage. Flanges for
cut-off wheels may be different from grinding
wheel flanges.
•Do not use worn down wheels from larger
power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.
Additional safety warnings
specific for abrasive cutting-off
operations
•Do not "jam" the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Over stressing the
wheel increases the loading and
susceptibility to twisting or binding of the
wheel in the cut and the possibility of
kickback or wheel breakage.
•Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away
from your body, the possible kickback may
propel the spinning wheel and the power tool
directly at you.
•When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the
cut while the wheel is in motion otherwise
kickback may occur. Investigate and take
corrective action to eliminate the cause of
wheel binding.
•Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
•Support panels or any oversized workpiece to
minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides
of the wheel.
•Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause
kickback.
Safety warnings specific for sanding
operations
•Do not use excessively oversized sanding
disc paper. Follow manufacturers
recommendations, when selecting sanding
paper. Larger sanding paper extending
beyond the sanding pad presents a laceration
hazard and may cause snagging, tearing of
the disc or kickback.
Safety warnings specific for polishing
operations
•Do not allow any loose portion of the
polishing bonnet or its attachment strings to
spin freely. Tuck away or trim any loose
attachment strings. Loose and spinning
attachment strings can entangle your fingers
or snag on the workpiece.

10
ENGLISH
Safety warnings specific for wire brushing
operations
•Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
•If the use of a guard is recommended for
wire brushing, do not allow any interference
of the wire wheel or brush with the guard.
Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
Safety of others
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
•Children should be supervised to ensure that
they do not play with the appliance.
Residual risks
Additional residual risks may arise when using
the tool which may not be included in the
enclosed safety warnings. These risks can arise
from misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks can not be
avoided. These include:
•Injuries caused by touching any
rotating/moving parts.
•Injuries caused when changing any parts,
blades or accessories.
•Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
•Impairment of hearing.
•Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF.)
Vibration
The declared vibration emission values stated in
the technical data and the declaration of
conformity have been measured in accordance
with a standard test method provided by EN
60745 and may be used for comparing one tool
with another.The declared vibration emission
value may also be used in a preliminary
assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to
protect persons regularly using power tools in
employment, an estimation of vibration exposure
should consider, the actual conditions of use and
the way the tool is used, including taking account
of all parts of the operating cycle such as the
times when the tool is switched off and when it is
running idle in addition to the trigger time.

11
ENGLISH
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury,
the user must read the instruction
manual.
Wear safety glasses or goggles when
operating this tool.
Wear ear protection when operating
this tool.
Electrical safety
This tool is double insulated; therefore
no earth wire is required.Always check
that the power supply corresponds to
the voltage on the rating plate.
•If the supply cord is damaged, it must be
replaced by the manufacturer or an
authorised Black & Decker Service Centre in
order to avoid a hazard.
Features
This tool includes some or all of the following
features.
1. On/off switch
2. Side handle
3. Spindle lock
4. Guard
Assembly
Warning! Before assembly, make sure that the
tool is switched off and unplugged.
Fitting and removing the guard
(fig.A)
The tool is supplied with a guard intended for
grinding purposes only. If the unit is intended to
perform cutting off operations, a guard specific
for this operation must be fitted.Asuitable guard
for cutting off operations part numbers
1004484-06 for KG750 and 1004484-07 for
KG751 are available and can be obtained from
Black & Decker service centres.
Fitting
•Place the tool on a table, with the spindle (5)
facing up.
•Release the clamping lock (7) and hold the
guard (4) over the tool as shown.
•Align the lugs (8) with the notches (9).
•Press the guard down and rotate it
counterclockwise to the required position.
•Fasten the clamping lock (7) to secure the
guard to the tool.
•If required, tighten the screw (6) to increase
the clamping force.
Removing
•Release the clamping lock (7).
•Rotate the guard clockwise to align the lugs
(8) with the notches (9).
•Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
•Screw the side handle (2) into one of the
mounting holes in the tool.
Warning!Always use the side handle.
Fitting and removing grinding or
cutting discs (fig. B - D)
Always use the correct type of disc for your
application.Always use discs with the correct
diameter and bore size (see technical data).
Fitting
•Fit the guard as described above.
•Place the inner flange (10) onto the spindle
(5) as shown (fig. B). Make sure that the
flange is correctly located on the flat sides of
the spindle.

12
ENGLISH
•Place the disc (11) onto the spindle (5) as
shown (fig. B). If the disc has a raised centre
(12), make sure that the raised centre faces
the inner flange.
•Make sure that the disc locates correctly on
the inner flange.
•Place the outer flange (13) onto the spindle.
When fitting a grinding disc, the raised centre
on the outer flange must face towards the
disc (Ain fig. C). When fitting a cutting disc,
the raised centre on the outer flange must
face away from the disc (B in fig. C).
•Keep the spindle lock (3) depressed and
tighten the outer flange using the two-pin
spanner (14) (fig. D).
Removing
•Keep the spindle lock (3) depressed and
loosen the outer flange (13) using the
two-pin spanner (14) (fig. D).
•Remove the outer flange (13) and the disc
(11).
Fitting and removing sanding
discs (fig. D & E)
For sanding, a backing pad is required. The
backing pad is available from your Black &
Decker dealer as an accessory.
Fitting
•Place the inner flange (10) onto the spindle
(5) as shown (fig. E). Make sure that the
flange is correctly located on the flat sides of
the spindle.
•Place the backing pad (15) onto the spindle.
•Place the sanding disc (16) onto the backing
pad.
•Place the outer flange (13) onto the spindle
with the raised centre facing away from the
disc.
•Keep the spindle lock (3) depressed and
tighten the outer flange using the two-pin
spanner (14) (fig. D). Make sure that the outer
flange is fitted correctly and that the disc is
clamped tightly.
Removing
•Keep the spindle lock (3) depressed and
loosen the outer flange (13) using the two-pin
spanner (14) (fig. D).
•Remove the outer flange (13), the sanding
disc (16) and the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do
not overload.
•Carefully guide the cable in order to avoid
accidentally cutting it.
•Be prepared for a stream of sparks when the
grinding or cutting disc touches the
workpiece.
•Always position the tool in such a way that
the guard provides optimum protection from
the grinding or cutting disc.
Switching on and off
•To switch on, slide the on/off switch (1)
forward. Note that the tool will continue
running when you release the switch.
•To switch off, press the rear part of the on/off
switch.
Warning! Do not switch the tool off while under
load.
Hints for optimum use
•Firmly hold the tool with one hand around the
side handle and the other hand around the
main handle.
•When grinding, always maintain an angle of
approx. 15° between the disc and the
workpiece surface.

13
ENGLISH
Maintenance
Your Black & Decker corded/cordless
appliance/tool has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance
on corded/cordless power tools:
•Switch off and unplug the appliance/tool.
•Or switch off and remove the battery from the
appliance/tool if the appliance/tool has a
separate battery pack.
•Or run the battery down completely if it is
integral and then switch off.
•Unplug the charger before cleaning it. Your
charger does not require any maintenance
apart from regular cleaning.
•Regularly clean the ventilation slots in your
appliance/tool/charger using a soft brush or
dry cloth.
•Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
•Regularly open the chuck and tap it to
remove any dust from the interior (when
fitted).
Mains Plug Replacement
If a new mains plug needs to be fitted:
•Safely dispose of the old plug.
•Connect the brown lead to the live terminal of
the new plug.
•Connect the blue lead to the neutral terminal.
•If the product is class l (earthed), connect the
green / yellow lead to the earth terminal.
Warning! If your product is class ll double
insulated (only 2 wires in the cord set), no
connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs.
Any replacement fuse must be of the same
rating as the original fuse supplied with the
product.
Technical Data
KG750 KG751
(Type 1) (Type 1)
Input voltage Vac 220-240 220-240
Power input W 750 750
No-load speed min-1 11,000 11,000
Disc diameter mm 115 125
Disc bore mm 22 22
Max disc thickness
Grinding discs mm 6 6
Cutting discs mm 3.5 3.5
Spindle size M14 M14
Weight kg 2.24 2.34

14
ENGLISH
Protecting the environment
Separate collection.This product must not
be disposed of with normal household
waste.
Should you find one day that your Black &
Decker product needs replacement, or if it is of
no further use to you, do not dispose of it with
other household waste. Make this product
available for separate collection.
•Black & Decker provides a facility for
recycling Black & Decker products once they
have reached the end of their working life.
This service is provided free of charge. To
take advantage of this service please return
your product to any authorised repair agent
who will collect them on our behalf.
•You can check the location of your nearest
authorised repair agent by contacting your
local Black & Decker office at the address
indicated in this manual.Alternatively, a list of
authorized Black & Decker repair agents and
full details of our after-sales service and
contact are available on the Internet at:
www.2helpU.com.
Warranty
If a Black & Decker product becomes defective
due to a material or manufacturing defect , within
12 months from the date of purchase, Black &
Decker guarantees to replace defective parts or
replace such products to ensure minimum
inconvenience to the customer unless:
•The product has been subjected to misuse or
neglect.
•The product has sustained damage through
foreign objects, substances or accidents.
•Repairs have been attempted by persons
other than authorised repair agents or Black
& Decker service staff.
To claim on the warranty, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting
your local Black & Decker office at the address
indicated in this manual.Alternatively, a list of
authorised Black & Decker repair agents and full
details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com.
Please visit our website www.blackanddecker.ae
to register your new Black & Decker product and
to be kept up to date on new products and
special offers. Further information on the Black &
Decker brand and our range of products is
available at www.blackanddecker.ae.

15
ARABIC
3
42
1

B
A
D
C
48
9
510 11 13 5 10 11 13
14
13
11
9
7
6
13
11
12
10
5
5
16
ARABIC

E
13
16
15
10
5
17
ARABIC

18
ARABIC
ΩGóîà°S’G ¢VôZ
ï∏÷ ôµjO ófBG ∑ÓH á«fGƒ£°S’G ï∏÷G áæ«cÉe º«ª°üJ ”
Ö°SÉæŸG ´ƒædG ΩGóîà°SÉH AÉæÑdG OGƒeh ¿OÉ©ŸG ™«£≤Jh
ºª°üe RÉ¡÷G Gòg ¿CÉH kɪ∏Y ,™«£≤àdG hCG ï∏÷G ¢UGôbCG øe
äGhOCÉH √ójhõJ á£jöT ;§≤a ∂∏¡à°ùŸG ᣰSGƒH ¬eGóîà°S’
.áeRÓdG ájÉbƒdG
áeÓ°ùdG äGOÉ°TQEG
á«FÉHô¡µdG Iõ¡LC’G ¢Uƒ°üîH áeÉ©dG áeÓ°ùdG äGôjò–
äGOÉ°TQEGh äGôjò– áaÉc IAGôb »¨Ñæj !ôjò–
äGôjòëàdG áaÉc ´ÉÑJEG ΩóY ÖÑ°ùàj ó≤a .áeÓ°ùdG
áeó°U çhóM ‘ √ÉfOCG IQƒcòŸG äGOÉ°TQE’Gh
AÉ«°TC’G √òg ™«ªL hCG IÒ£N áHÉ°UEG hCG ≥jôM hCG á«FÉHô¡c
.kɩe
´ƒLô∏d äGOÉ°TQE’Gh äGôjòëàdG áaɵH ®ÉØàM’G ≈Lôj
.kÓÑ≤à°ùe É¡«dEG
áaÉc ‘ OQGƒdG "»FÉHô¡c RÉ¡L"í∏£°üŸG Ò°ûj
…òdG »FÉHô¡µdG RÉ¡÷G ¤EG √ÉfOCG IQƒcòŸG äGôjòëàdG
»FÉHô¡µdG RÉ¡÷G hCG (Ék«µ∏°S) »FÉHô¡µdG QÉ«àdÉH πª©j
.(Ék«µ∏°S’) ájQÉ£ÑdÉH πª©j …òdG
πª©dG á≤£æe áeÓ°S .1
É¡JAÉ°VEGh πª©dG á≤£æe áaɶf ≈∏Y ®ÉØ◊G »¨Ñæj .CG
ΩÉcôdÉH á¶àµŸG hCG áª∏¶ŸG ≥WÉæŸG ÖÑ°ùàJ PEG ,Gkó«L
.çOGƒ◊G ´ƒbh ‘
á∏HÉb AGƒLCG ‘ á«FÉHô¡µdG Iõ¡LC’G 𫨰ûàH º≤J ’ .Ü
hCG äGRÉZ hCG πFGƒ°S OƒLh ‘ É¡∏«¨°ûJ πãe ;QÉéØfÓd
á«FÉHô¡µdG Iõ¡LC’G ¿C’ kGô¶f ,∫É©à°TÓd πHÉb QÉÑZ
hCG QÉѨdG ∫É©à°TG ¤EG …ODƒJ ób äGQGöT É¡æY èàæj
.áæNOC’G
RÉ¡÷G 𫨰ûJ AÉæKCG IQÉŸGh ∫ÉØWC’G OÉ©HEG »¨Ñæj .ê
Iô£«°ù∏d ∂fGó≤a ‘ AÉ¡dE’G ÖÑ°ùàj ó≤a ,»FÉHô¡µdG
.RÉ¡÷G ≈∏Y
á«FÉHô¡µdG áeÓ°ùdG .2
™e á≤aGƒàe »FÉHô¡µdG RÉ¡÷G ¢ùHGƒb ¿ƒµJ ¿CG Öéj .CG
¢ùHÉ≤dG πjó©J Ék≤∏£e ÖæŒ .»FÉHô¡µdG QÉ«àdG òNCÉe
™e ä’ƒfi ¢ùHGƒb ájCG Ωóîà°ùJ ’h ,á≤jôW ájCÉH
ádó©ŸG ÒZ ¢ùHGƒ≤dG ΩGóîà°SG ¿C’ ,á°VQDƒŸG Iõ¡LC’G
π«∏≤J ¤EG …ODƒj á≤aGƒàŸG »FÉHô¡µdG QÉ«àdG òNBÉeh
.á«FÉHô¡c áeó°üd ¢Vô©àdG ôWÉfl
Ö«HÉfC’G πãe á°VQDƒŸG í£°SCÓd ∂ª°ùL á°ùeÓe ÖæŒ .Ü
ôWÉfl OGOõJ å«M ,äÉLÓãdGh óbGƒŸGh áÄaóàdG Iõ¡LCGh
.É k °VQDƒe ∂ª°ùL ¿Éc GPEG á«FÉHô¡c áeó°üH ∂àHÉ°UEG
,áÑWôdG AGƒLC’G hCG ô£ª∏d á«FÉHô¡µdG Iõ¡LC’G ¢Vô©J ’ .ê
¤EG »FÉHô¡µdG RÉ¡÷G πNGO AÉŸG ∫ƒNO …ODƒj ±ƒ°ùa
.á«FÉHô¡c áeó°üH áHÉ°UE’G ôWÉfl IOÉjR
.ÅWÉN πµ°ûH »FÉHô¡µdG QÉ«àdG ∂∏°S ΩGóîà°SG ΩóY Öéj .O
RÉ¡÷G πª◊ »FÉHô¡µdG QÉ«àdG ∂∏°S Ék≤∏£e Ωóîà°ùJ ’
ɪc .»FÉHô¡µdG QÉ«àdG øY ¬∏°üa hCG ¬Ñë°S hCG »FÉHô¡µdG
IQGô◊G øY Gkó«©H »FÉHô¡µdG QÉ«àdG ∂∏°ùH ®ÉØàM’G Öéj
kɪ∏Y .ácôëàŸG AGõLC’G hCG IOÉ◊G ±Gƒ◊G hCG âjõdG hCG
ôWÉfl øe ójõJ áµHÉ°ûàŸG hCG áØdÉàdG ∑Ó°SC’G ¿CÉH
.á«FÉHô¡c áeó°üH áHÉ°UE’G
Öéj ,êQÉÿG ‘ »FÉHô¡µdG RÉ¡÷G 𫨰ûJ óæY .`g
,»LQÉÿG ΩGóîà°SÓd Ö°SÉæŸG π«°UƒàdG ∂∏°S ΩGóîà°SG
Ö°SÉæŸG »FÉHô¡µdG QÉ«àdG ∂∏°S ΩGóîà°SG ¿C’ kGô¶f
áeó°üd ¢Vô©àdG ôWÉfl øe π∏≤j »LQÉÿG ΩGóîà°SÓd
.á«FÉHô¡c
Öéj ,ÖWQ ¿Éµe ‘ »FÉHô¡µdG RÉ¡÷G 𫨰ûJ ºà– GPEG.h
¿C’ kGô¶f ,»≤ÑàŸG QÉ«àdG øe ájÉbh RÉ¡L ΩGóîà°SG
øe π∏≤j »≤ÑàŸG QÉ«àdG øe ájÉbh RÉ¡L ΩGóîà°SG
.á«FÉHô¡c áeó°üH áHÉ°UE’G ôWÉfl
á«°üî°ûdG áeÓ°ùdG .3
óæY º«∏°ùdG ¢ù◊G Ωóîà°SGh ¬∏©ØJ ÉŸ ¬ÑàfGh kGQòM øc .CG
»FÉHô¡µdG RÉ¡÷G Ωóîà°ùJ ’ .»FÉHô¡µdG RÉ¡÷G 𫨰ûJ
äÉHhöûŸG hCG ÒbÉ≤©dG ÒKCÉJ â– hCG Ékµ¡æe âæc GPEG
AÉæKCG á∏بdG øe á¶◊ ÖÑ°ùàJ ó≤a ,ájhOC’G hCG á«dƒëµdG
á«°üî°T áHÉ°UEG çhóM ‘ á«FÉHô¡µdG Iõ¡LC’G 𫨰ûJ
.á¨dÉH
m ¥Gh ÉkehO …óJQG .á«°üî°ûdG ájÉbƒdG äGó©e Ωóîà°SG .Ü
äÉeɪc πãe ,ájÉbƒdG äGó©e ΩGóîà°SG ¿C’ ,Úæ«©∏d
áÑ∏°üdG äGPƒÿGh ¥’õfÓd á©fÉŸG ájòMC’Gh áHôJC’G
äÉHÉ°UEG çhóM ôWÉfl øe π∏≤j ,™ª°ùdG ájÉbh äGhOCGh
.á«°üî°T
¿hO ∫ƒë∏d áeRÓdG äÉWÉ«àM’G áaÉc PÉîJG Öéj .ê
óY ™°Vh ‘ ìÉàØŸG ¿CG ócCÉJ .ó°üb ¿hO RÉ¡÷G 𫨰ûJ
hCG/h »FÉHô¡µdG QÉ«àdG Qó°üà π«°UƒàdG πÑb 𫨰ûàdG
πªM ¿CG PEG .¬∏ªM hCG RÉ¡÷G ™aQ hCG ,äÉjQÉ£ÑdG Ö«côJ
hCG ìÉàت∏d á°ùeÓe ™HÉ°UC’Gh á«FÉHô¡µdG Iõ¡LC’G
™°Vh ‘ ìÉàØŸGh ábÉ£dÉH á«FÉHô¡µdG Iõ¡LC’G ójhõJ
.çOGƒM ´ƒbh ¤EG …ODƒj 𫨰ûàdG

19
ARABIC
𫨰ûJ πÑb §HQ ìÉàØe hCG πjó©J ìÉàØe …CG ádGREÉH ºb .O
kÉ`≤∏©e ìÉàØŸG ∑ôJ ÖÑ°ùàj ó≤a ,»FÉHô¡µdG RÉ¡÷G
áHÉ°UEG çhóM ‘ »FÉHô¡µdG RÉ¡÷G øe QGhódG Aõ÷ÉH
.á«°üî°T
Öéj ɪc ,•ôØe πµ°ûH RÉ¡÷G øe ÜGÎb’G ΩóY Öéj .`g
¿C’ ,πª©dG AÉæKCG ¿RGƒàdGh Úeó≤dG äÉÑK ≈∏Y ®ÉØ◊G
RÉ¡÷G ≈∏Y ó«L πµ°ûH Iô£«°ùdG ∂d í«àj ∂dP
.á©bƒàŸG ÒZ ∞bGƒŸG ‘ »FÉHô¡µdG
¢ùHÓŸG AGóJQG ΩóYh ,áÑ°SÉæŸG ¢ùHÓŸG AGóJQG Öéj .h
∂°ùHÓeh ∑ô©°T AÉ≤HEG Öéj ɪc ,»∏◊G hCG á°VÉØ°†ØdG
¢ùHÓŸG ¿C’ ,ácôëàŸG AGõLC’G øY Gkó«©H ∂jRÉØbh
™e ∂HÉ°ûàj ób ‹óàŸG ô©°ûdG hCG »∏◊G hCG á°VÉØ°†ØdG
.ácôëàŸG AGõLC’G
hCG QÉѨdG êGôîà°S’ äGhOCÉH kGOhõe RÉ¡÷G ¿Éc GPEG.R
É¡eGóîà°SGh äGhOC’G ∂∏J π«°UƒJ øe ócCÉJ ,¬©«ªŒ
øe π∏≤j äGhOC’G √òg ΩGóîà°SG ¿C’ ,Ö°SÉæe πµ°ûH
.QÉѨdÉH á£ÑJôŸG ôWÉîŸG
¬H ájÉæ©dGh »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG .4
ÒZ ¢VôZ ‘ »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ΩóY Öéj .CG
»FÉHô¡µdG RÉ¡÷G Ωóîà°SG Öéj πH ,¬d ¢ü°üfl
»FÉHô¡µdG RÉ¡÷G ¿C’ ,√ójôJ …òdG ¢Vô¨dÉH ¢UÉÿG
ÉkfÉeCG ÌcCGh π°†aCG πµ°ûH πª©dG …ODƒj ±ƒ°S Ö°SÉæŸG
.¬∏LCG øe ¬ª«ª°üJ ” …òdG ∫ó©ŸÉHh
‘ ºµëàdG ™£à°ùJ ⁄ kGPEG »FÉHô¡µdG RÉ¡÷G Ωóîà°ùJ ’ .Ü
…CG ¿C’ ,ìÉàØŸG ᣰSGƒH ¬∏«¨°ûJ ±É≤jEGh ¬∏«¨°ûJ
ìÉàØŸG ΩGóîà°SÉH ¬«a ºµëàdG øµÁ ’ »FÉHô¡c RÉ¡L
.¬MÓ°UEG Öéjh ôWÉîŸÉH kÉaƒØfi ¿ƒµj
QÉ«àdG Qó°üe øY »FÉHô¡µdG RÉ¡÷G ¢ùHÉb π°üa Öéj .ê
hCG äÓjó©J ájCG AGôLEG πÑb äÉjQÉ£ÑdG hCG/h »FÉHô¡µdG
Iõ¡LC’G ‘ äÉ≤ë∏e ájCG Ö«côJ hCG äGÒ«¨J
á«FÉbƒdG áeÓ°ùdG äGAGôLEG ¿C’ ,É¡æjõîJ hCG á«FÉHô¡µdG
»FÉHô¡µdG RÉ¡÷G 𫨰ûJ AóH ôWÉfl øe π∏≤J √òg
.ó°üb ¿hO ICÉéa
áeóîà°ùŸG ÒZ á«FÉHô¡µdG Iõ¡LC’G øjõîJ Öéj .O
ÒZ ¢UÉî°TCÓd íª°ùJ ’h ∫ÉØWC’G ∫hÉæàe øY Gkó«©H
ÒZ hCG »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ≈∏Y øjOÉà©ŸG
RÉ¡÷G 𫨰ûàH äGOÉ°TQE’G √òg ≈∏Y Ú©∏£ŸG
ÉeóæY kGô£N πµ°ûJ á«FÉHô¡µdG Iõ¡LC’Éa ,»FÉHô¡µdG
.ÚHQóe ÒZ ¢UÉî°TCG É¡eóîà°ùj
¢üëaG .á«FÉHô¡µdG Iõ¡LCÓd ájQhO áfÉ«°U AGôLEG Öéj .`g
¥ƒ©J »àdG hCG ¬«a áÑ«©ŸG AGõLC’G ≈∏Y ±ô©à∏d RÉ¡÷G
AGõLC’G øe √ƒ∏N øe ócCÉàdGh ácôëàŸG AGõLC’G ácôM
.¬∏«¨°ûJ IAÉØc ≈∏Y ôKDƒj ób ôNBG A»°T …CG øeh IQƒ°ùµŸG
RÉ¡÷G ìÓ°UEG Öéj ,∞∏J …CG ±É°ûàcG ” GPEGh
çOGƒ◊G øe ójó©dG ¿CÉH kɪ∏Y ,¬eGóîà°SG πÑb »FÉHô¡µdG
.á«FÉHô¡µdG Iõ¡LC’G áfÉ«°U Aƒ°S ÖÑ°ùH ™≤J
¿C’ ,áØ«¶fh kIOÉM ™£≤dG äGhOCG ≈∏Y ®ÉØ◊G »¨Ñæj .h
Ö°SÉæŸG πµ°ûdÉH É¡«∏Y ®ÉØ◊G ºàj »àdG ™£≤dG äGhOCG
∫É£YCÓd á°VôY πbCG IOÉM á©WÉb äGôØ°ûH IOhõŸGh
.ºµëàdG ‘ π¡°SCGh
¬FGõLCGh ¬JÉ≤ë∏eh »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG Öéj .R
±hôX òNCG ™e ,äGOÉ°TQE’G √ò¡d Ék≤ah ∂dP ¤EG Éeh
ó≤a ,QÉÑàY’G ‘ √ò«ØæJ OGôŸG πª©dGh ᣫëŸG πª©dG
äÉ«∏ªY πLCG øe »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ÖÑ°ùàj
çhóM ‘ É¡∏LCG øe ºª°üŸG ¢VGôZC’G iƒ°S 𫨰ûJ
.ôWÉfl
áfÉ«°üdG .5
ᣰSGƒH »FÉHô¡µdG RÉ¡÷G ìÓ°UEGh áfÉ«°U Öéj .CG
∂dP ¿C’ ,á≤HÉ£e QÉ«Z ™£b ΩGóîà°SÉH πgDƒe ¢üî°T
.»FÉHô¡µdG RÉ¡÷G áeÓ°S øª°†j
RÉ¡÷G ¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò–
»FÉHô¡µdG
¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò– !ôjò–
¢TôØdÉH ∞«¶æàdG hCG IôØæ°üdG hCG ï∏÷G äÉ«∏ªY
.»î«∏éàdG ™«£≤àdG hCG ™«ª∏àdG hCG ᫵∏°ùdG
ï∏L áæ«cɪc ¬eGóîà°S’ »FÉHô¡µdG RÉ¡÷G Gòg ºª°U
•
Öéj .᫵∏°S IÉ°TôØc hCG ™«£≤J hCG ™«ª∏J hCG IôØæ°U hCG
Ωƒ°SôdGh äGOÉ°TQE’Gh ¿ÉeC’G äGôjò– áaÉc IAGôb
RÉ¡÷G Gòg ™e IOhõŸG äÉØ°UGƒŸGh á«ë«°VƒàdG
äGOÉ°TQE’G ™«ªL ´ÉÑJG ΩóY ¿CÉH kɪ∏Y ,»FÉHô¡µdG
hCG á«FÉHô¡c áeó°U çhóM ¤EG …ODƒj ób √ÉfOCG IOQGƒdG
.kÉ©e AÉ«°TC’G √òg ™«ªL hCG IÒ£N äÉHÉ°UEG hCG ≥FGôM
ºàj ⁄ ¢VGôZCG ‘ »FÉHô¡µdG RÉ¡÷G Gòg ΩGóîà°SG
•
ÖÑ°ùàjh ôWÉîŸG øe ójó©dG ódƒj ób É¡∏LCG øe ¬ª«ª°üJ
.á«°üî°T äÉHÉ°UEG çhóM ‘

20
ARABIC
á©æ°üŸG ácöûdG É¡ªª°üJ ⁄ äÉ≤ë∏e Ωóîà°ùJ ’ •
»æ©j ’h .É¡eGóîà°SÉH â°UhCGh RÉ¡÷G Gò¡d kÉ°ü«°üN
¿CG ,»FÉHô¡µdG RÉ¡÷ÉH ≥ë∏e …CG Ö«côJ øµÁ ¬fCG
.¿ÉeCÉH 𪩫°S RÉ¡÷G
≈∏Y ájhÉ°ùe ≥ë∏ª∏d áØæ°üŸG áYöùdG ¿ƒµJ ¿CG Öéj
•
RÉ¡÷G ≈∏Y IOóëŸG iƒ°ü≤dG áYöù∏d πbC’G
áYöùH É¡∏«¨°ûJ ºàj »àdG äÉ≤ë∏ŸG ¿C’ ,»FÉHô¡µdG
.kGó«©H ôjÉ£àJh öùµæJ ób áØæ°üŸG É¡àYöS RhÉéàJ
¬µª°Sh ≥ë∏ª∏d »LQÉÿG ô£≤dG ¿ƒµj ¿CG Öéj
•
¿C’ ,»FÉHô¡µdG RÉ¡é∏d IQó≤dG ∞«æ°üJ ™e Ú≤aGƒàe
hCG É¡àjÉbh øµÁ ’ áÑ°SÉæŸG ÒZ äÉ≤ë∏ŸG ΩÉéMCG
.É¡«∏Y Iô£«°ùdG
hCG äÉéæ∏ØdG hCG äÓé©dG ´òL ºéM ¿ƒµj ¿CG Öéj
•
Oƒª©d kÉeÉ“ kÉÑ°SÉæe ôNBG ≥ë∏e …CG hCG ºYódG íFÉØ°U
»àdG äÉ≤ë∏ŸG ¿C’ ,»FÉHô¡µdG RÉ¡÷G ‘ ¿GQhódG
äGó©e ™e á≤HÉ£àe ÒZ ´hòL äÉëàa ≈∏Y …ƒà–
ÒZ IQƒ°üH πª©J ób »FÉHô¡µdG RÉ¡÷G ‘ Ö«cÎdG
¿Gó≤a ‘ ÖÑ°ùàj ób Ée ,•ôØe πµ°ûH õà¡Jh áfRGƒàe
.RÉ¡÷G ≈∏Y Iô£«°ùdG
πc πÑb Öéjh .kÉ≤∏£e kÉHƒ£©e kÉ≤ë∏e Ωóîà°ùJ ’
•
kÉãëH ï∏÷G äÓéY πãe äÉ≤ë∏ŸG ¢üëa ΩGóîà°SG
øY kÉãëH ºYódG íFÉØ°Uh ,¥ƒ≤°ûdGh Éjɶ°ûdG øY
IÉ°TôØdGh ,ó◊G øY óFGõdG πcBÉàdG hCG ≥≤°ûàdGh ,¥ƒ≤°ûdG
GPEGh .á≤≤°ûàŸG hCG áÑFÉ°ùdG ∑Ó°SC’G øY kÉãëH ᫵∏°ùdG
¬°üëa Öéj ,¬JÉ≤ë∏e hCG »FÉHô¡µdG RÉ¡÷G §≤°S
äÉ≤ë∏e Ö«côJ hCG QöV …CÉH ¬àHÉ°UEG ΩóY øe ócCÉà∏d
Öéj ,äÉ≤ë∏e …CG Ö«côJh ¢üëa ó©Hh .᪫∏°S iôNCG
™°Vh ‘ áYöS ≈°übCÉH »FÉHô¡µdG RÉ¡÷G 𫨰ûJ
öùµæJ Ée kIOÉ©a ,á∏eÉc á≤«bO IóŸ π«ªëàdG ΩóY
.√òg QÉÑàN’G Ióe ∫ÓN áØdÉàdG äÉ≤ë∏ŸG
≈∏Y kGOɪàYGh .á«°üî°ûdG ájÉbƒdG äGó©e AGóJQG Öéj
•
¬Lƒ∏d ájɪM IGOCG Ωóîà°SG ,¬H Ωƒ≤J …òdG πª©dG ´ƒf
áHôJCG áeɪc …óJQG ,IQhö†dG óæYh .á«bGh äGQɶfh
≈∏Y QOÉb πªY á°TQh AGOQh äGRÉØbh ™ª°ù∏d äÉ«bGhh
ï∏÷G AÉæKCG ôjÉ£àJ »àdG IÒ¨°üdG Éjɶ°ûdG øe ∂àjɪM
äGQɶædG ¿ƒµJ ¿CG Öéj ɪc ,πª©dG á©£b øe hCG
øY Å°TÉædG ôjÉ£àŸG ΩÉcôdG ó°U ≈∏Y IQOÉb á«bGƒdG
¿ƒµJ ¿CG Öéj ,∂dP ¤EG áaÉ°VEG .áØ∏àîŸG äÉ«∏ª©dG
í«°TôJ ≈∏Y IQOÉb ¢ùØæàdG áeɪc hCG áHôJC’G áeɪc
¢Vô©àdG …ODƒj óbh .πª©dG AÉæKCG áŒÉædG äÉÄjõ÷G
.™ª°ùdG ¿Gó≤a ¤EG á∏jƒW IóŸ Ió°ûdG á«dÉY AÉ°Vƒ°†d
ɪc ,πª©dG á≤£æe øe kGóL ÜGÎb’ÉH IQɪ∏d íª°ùJ ’
•
πª©dG á≤£æe ¤EG ΩOÉb ¢üî°T …CG …óJôj ¿CG Öéj
á©£b Éjɶ°T ôjÉ£àJ ó≤a ,á«°üî°ûdG ájÉbƒdG äGó©e
áHÉ°UEG çhóM ‘ ÖÑ°ùàJh IQƒ°ùµŸG äÉ≤ë∏ŸG hCG πª©dG
.πª©dG á≤£æà kIöTÉÑe ᣫëŸG á≤£æŸG ‘
äGP ∑É°ùeEG äGhOCG ᣰSGƒH »FÉHô¡µdG RÉ¡÷G ∂°ùeG
•
ób ™«£≤àdG ≥ë∏e ¿C’ ,Ée á«∏ªY AGOCG óæY ádhõ©e í£°SCG
¢UÉÿG ∂∏°ùdG hCG »Øfl »FÉHô¡c QÉ«J ∂∏°S ¢ùeÓj
¬«a …öùj ∂∏°ùd ™«£≤àdG ≥ë∏e á°ùeÓe …ODƒJ óbh ,É¡H
RÉ¡÷G ‘ á«fó©ŸG AGõLC’G ájô©J ¤EG "»FÉHô¡c QÉ«J"
¢Vô©Jh ¬«a »Hô¡µdG QÉ«àdG ¿ÉjöSh »FÉHô¡µdG
.á«FÉHô¡c áeó°üd Ωóîà°ùŸG
≥ë∏ŸG øY kÉeÉ“ »FÉHô¡µdG QÉ«àdG ∂∏°S OÉ©HEG Öéj
•
ób ,RÉ¡÷G ≈∏Y Iô£«°ùdG ¿Gó≤a ádÉM ‘ ¬fC’ ,QGhódG
∂YGQP hCG ∑ój ¬©e Öë°ùjh ≥∏©j hCG ∂∏°ùdG ™£≤æj
.QGhódG ≥∏ëŸG √ÉŒÉH
∞bƒàj ⁄ Ée í£°S …CG ≈∏Y »FÉHô¡µdG RÉ¡÷G ∑ÎJ ’
•
QGhódG ≥ë∏ŸG Ωƒ≤j ó≤a ,kÉeÉ“ ¿GQhódG øY ¬≤ë∏e
RÉ¡÷G ≈∏Y Iô£«°ù∏d ∑OÉ≤aEGh í£°ùdG ÜòéH
.»FÉHô¡µdG
QGƒéH ¬∏ªM óæY »FÉHô¡µdG RÉ¡÷G 𫨰ûàH º≤J ’
•
∂°ùHÓà káaó°U ¢ùeÓàj ób QGhódG ≥ë∏ŸG ¿C’ ,∂ÑfÉL
.∂ª°ùL √ÉŒ ≥ë∏ŸG ÜòéH Ωƒ≤jh É¡H ≥∏©jh
»FÉHô¡µdG RÉ¡÷G ‘ ájƒ¡àdG äÉëàa ∞«¶æJ Öéj
•
πNGO QÉѨdG Öë°ùJ ∑ôëŸG áMhôe ¿C’ ,ΩɶàfÉH
QÉѨd •ôØŸG ºcGÎdG …ODƒj óbh ∑ôëŸG ¥hóæ°U
.á«FÉHô¡c ôWÉfl çhóM ¤EG ¿OÉ©ŸG