Black & Decker BDSG500 Linea PRO User manual

www.blackanddecker.eu
BDSG500

2
English (Original instructions) 5
Türkçe (Çevirisi orijinal talimatlardan yapılmıştır) 12

3
3
1
2
4
4
5
5
5
6
FIG. A / ŞEKİL A
FIG. B
ŞEKİL B
FIG. C / ŞEKİL C

4
5
6
7
1
1
2
2
2
10
8
7
1
89
FIG. D / ŞEKİL D
FIG. F / ŞEKİL F
FIG. H / ŞEKİL H
FIG. J / ŞEKİL J
FIG. E / ŞEKİL E
FIG. G / ŞEKİL G
FIG. I / ŞEKİL I
FIG. K / ŞEKİL K

5
ENGLISH
GENERAL SAFETY RULES
Warning! Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
Intended Use
This Black & Decker screwdriver has been
designed for driving drywall fasteners through
drywall board into timber or metal framing studs.
SAVE THESE INSTRUCTIONS
General power tool safety
warnings.
Warning! Read all safety warnings
and all instructions. Failure to follow the warnings
and instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. The term “power tool” in all of the
warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
1. Work Area Safety
a. Keep work area clean and well lit. Cluttered
and dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical Safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body
is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock. Note:
The term “Residual Curent Device (RCD)”
can be replaced by “Ground Fault Circuit
Interrupter (GFCI)” or by “Earth Leakage
Circuit Breaker (ELCB)”.
3. Personal Safety
a. Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.

6
ENGLISH
g. If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of these devices can reduce dust
related hazards.
4. Power Tool Use and Care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Service
a. Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will ensure
that the safety of the power tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore
no earth wire is required. Always check
that the main voltage corresponds to the
voltage on the rating plate.
Warning! If the power cord is damaged,
it must be replaced by the manufacturer,
authorized Вlack & Decker Service Center
or an equally qualified person in order to
avoid damage or injury. If the power cord
is replaced by an equally qualified person,
but not authorized by Вlack & Decker, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the
following symbols:
Read In-
structions
Manual
Hz Hertz Class II
Construc-
tion
Use Eye
Protection
W Watts Earthing
Terminal
Use Ear
Protection
min minutes Safety Alert
Symbol
VVolts Alternating
Current
../min Revolu-
tions or
Recipro-
cation per
minute
AAmperes Direct
Current
n0No-Load
Speed
FEATURES (Fig. A)
1. Depth stop
2. Depth adjuster
3. Belt clip
4. Forward/Reverse switch
5. Variable speed trigger switch
6. Lock-on button
SPECIFIC SAFETY RULES
Hold power tool by insulated gripping surfaces,
when performing an operation where the
fastener may contact hidden wiring or its own
cord. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Warning! Know your drywall screwdriver. Do
not plug the tool into the power source until
you have read and understand this Instruction

7
ENGLISH
Manual. Learn the tool’s applications and
limitations, as well as the specific potential
hazards related to this tool.
►Following this rule will reduce the risk of
electric shock, fire, or serious injury.
►Always wear eye protection. Any power tool
can throw foreign objects into your eyes and
cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with
ANSI safety standard Z87.1. Everyday glasses
have only impact resistant lenses. They ARE
NOT safety glasses
Warning! Glasses or goggles not in compliance
with ANSI Z87.1 could cause serious injury when
they break.
►Never use the drywall screwdriver to drive
screws other than drywall screws. The drywall
screwdriver and the screwdriver bits are
designed specifically for driving drywall screws.
►Only use screwdriver bits that are designed for
use with this tool.
►Always keep hands out of the path of the
drywall screw.
►Make sure there are no nails or foreign objects
in the part of the workpiece to be cut or
sanded.
►To avoid injury from accidental starting, always
remove the plug from the power source before
installing or removing a screwdriver bit or when
adjusting the depth control.
►Always check the wall area where screws
will be driven to be sure there are no hidden
electrical wires in the area.
►Never leave the Lock-on button ON. Before
plugging the tool into the power source, make
sure the lock-on button is OFF.
GENERAL SAFETY WARNINGS
Warning! Wear a dust mask that is designed
to be used when operating a power tool in
a dusty environment.
Warning! Dust that is created by power sanding,
sawing, grinding, drilling, and other construction
activities may contain chemicals that are known
to cause cancer, birth defects, or other genetic
abnormalities. These chemicals include:
►Lead from lead-based paints
►Crystalline silica from bricks, cement, and
other masonry products
►Arsenic and chromium from chemically treate
lumber
The level of risk from exposure to these chemicals
varies, according to how often this type of work is
performed. In order to reduce exposure to these
chemicals, work in a well-ventilated area, and use
approved safety equipment, such as a dust mask
that is specifically designed to filter out microscopic
particles.
Residual risks.
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from
misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks can not be avoided.
These include:
►Injuries caused by touching any rotating/
moving parts.
►Injuries caused when changing any parts,
blades or accessories.
►Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
►Impairment of hearing.
►Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF.)
Vibration
The declared vibration emission values stated in
the technical data and the declaration of conformity
have been measured in accordance with a
standard test method provided by EN 60745 and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to
protect persons regularly using power tools in
employment, an estimation of vibration exposure
should consider, the actual conditions of use and
the way the tool is used, including taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time.

8
ENGLISH
SEGURIDAD DEL CABLE DE
EXTENSIÓN
Warning! Keep the extension cord clear of
the working area. Position the cord so it will not
get caught on the workpiece, tools or any other
obstructions while you are working with the power
tool.
Make sure any extension cord used with this tool is
in good condition. When using an extension cord,
be sure to use one of heavy enough gauge to carry
the current the tool will draw. An undersized cord
will cause a drop in line voltage resulting in loss of
power and overheating.
Be sure your extension cord is properly wired and
in good condition. Always replace a damaged
extension cord or have it repaired by a qualified
electrician before using it. Protect your extension
cord from sharp objects, excessive heat and damp
or wet areas.
Use a separate electrical circuit for your power
tools. This circuit must not be less than 14 gauge
wire and should be protected with either a 15
A time delayed fuse or circuit breaker. Before
connecting the power tool to the power source,
make sure the switch is in the OFF position and
the power source is the same as indicated on the
nameplate. Running at lower voltage will damage
the motor.
CONTENTS
Carefully unpack the drywall screwdriver. Compare
the contents against the “Drywall screwdriver
components” chart below.
ASSEMBLY AND OPERATING
Warning! To avoid fire or toxic reaction, never
use gasoline, naphtha, acetone, lacquer thinner or
similar highly volatile solvents to clean the tool.
Forward/Reverse switch (Fig. B)
The forward/reverse switch (4) is conveniently
mounted in front of the variable speed trigger
switch (5). To make the screwdriver rotate
clockwise for driving screws, push the forward/
reverse switch (4) to the left. To make the
screwdriver rotate counter-clockwise to remove
screws, push the forward/reverse switch (4) to the
right.
Notes:
a. Never change the position of the forward/
reverse switch (4) while the screwdriver bit is
turning.
b. The variable speed trigger switch (5) will NOT
function with the forward/reverse switch (4) in
the middle position.
Variable speed trigger switch (Fig. C)
This screwdriver is equipped with a variable speed
On/Off trigger switch.
1. To start screwdriver, gently squeeze the
variable speed trigger switch (5).
Note: The screwdriver will turn at its slowest
speed when the variable speed trigger switch
is depressed slightly. The screwdriver will turn
at its fastest speed when the variable speed
trigger switch is fully depressed.
2. To stop the screwdriver, release the variable
speed trigger switch (5).
Lock-on button (Fig. D)
The lock-on button feature allows the trigger switch
to be locked in the ON position at full speed when
continuous operation for extended periods of time
is required.
To lock the lock-on button in the ON position,
pull back on the variable speed trigger switch
(5) to start the screwdriver and push the lock-on
button (6) into the screwdriver handle. Release
the variable speed trigger switch while holding the
lock-on button into the screwdriver handle. The
screwdriver will continue to run. To release the
lock-on button, pull variable speed trigger switch
back (5) and then release the trigger.
Note: Operating the screwdriver with the variable
speed trigger switch for an extended period of time
may cause the screwdriver motor to overheat. If
the screwdriver gets hot, stop driving screws and
allow it to cool for at least 15 minutes.
Inserting a screwdriver bit (Fig. E)
This tool has a magnetic bit holder that provides
convenient bit changes. To install a bit, simply
insert the hex bit shank (7) into the magnetic bit
holder (8) that is located inside the depth stop (1).
Push the bit into the magnetic bit holder until the
magnet holds the bit in place.
Notes:
a. Use only 1” (25 mm) long bits that are
designed for use in driving drywall screws.
b. Make sure the bit size is correct for the drywall
screws being driven. This will usually be a #2
size.

9
ENGLISH
Replacing the magnetic bit holder (Fig. F)
If the magnetic bit holder becomes worn or
damaged, it must be replaced. The replacement
bit holder must be of the same dimensions as the
original and have the ANSI retention groove on the
end that is inserted into the tool.
1. Remove the nosepiece (2) by turning it counter
clockwise.
Note: Do not use pliers on the nosepiece. Only
use your hand.
2. Grasp the screwdriver bit (7) with pliers and
pull it out of the magnetic bit holder (8).
3. Grasp the large end of the bit holder with
pliers and pull it straight out of the screwdriver
spindle (9).
4. Reverse the process by inserting the
replacement magnetic bit holder into the tool.
Note: When inserting the replacement for
magnetic bit holder, gently tap it into place to
make sure it is fully inserted. Grasp the large
end of the magnetic bit holder to ensure the
retention groove (10) is holding the magnetic
bit holder in place in the tool.
5. Reinstall the screwdriver bit and nose piece.
SAFETY RECOMMENDATIONS
Check the following every time you use the
screwdriver:
1. Wear safety glasses or a mask.
2. Use hearing protection.
3. The screwdriver tip is the right size and it is in
good condition.
4. No power cables “live” where you are inserting
the screws.
Note: Failure to follow these safety rules will
significantly increase the risk of injury.
Adjusting the screwdrive bit depth (Fig. G)
It is important to control the depth to which the
drywall screw will be driven. Over driving the
screw will drive the screw too deep and break the
outer paper layer of the drywall. Under driving the
screw will leave the screw head above the drywall
surface making it impossible to properly finish the
drywall.
The depth control system is made up of the depth
stop (1) and the depth adjuster (2).
Warning! The following adjustments should
always be verified using a scrap piece of drywall to
avoid damaging the “good” drywall sections.
1. Rotate the depth adjuster counter clockwise
until approximately 1/4” of the screwdriver bit
extends beyond the depth stop.
2. Place a drywall screw onto the screwdriver bit.
The magnetized bit will hold the screw onto the
bit.
Note: Before driving the screw, press the
screw point into the drywall and make sure the
screw is perpendicular to the drywall.
3. Press the screw against the drywall with
steady even pressure and squeeze the trigger
switch. The clutch in the tool will engage and
the screw will be driven to the preset depth.
4. If the screw is not driven deep enough, the
head of the screw will not be recessed into the
drywall (Fig. H). In this case, turn the depth
adjustment sleeve clockwise until the correct
depth has been achieved. If the screw is driven
too deep, it will be recessed too far into the
drywall and the outer paper of the drywall
will be fractured (Fig. I). In this case, turn the
depth adjustment sleeve counter clockwise
until the correct depth has been achieved. Fig.
J illustrates the correct depth for the screw to
be driven.
Note: For each revolution the depth
adjustment sleeve is rotated, the depth will
increase/decrease approximately 1/16”
(1.6 mm).
Tips for driving drywall screws
►Always drive the screws perpendicular to the
drywall so the heads are properly countersunk.
They should never be driven at an angle.
►Support the tool with both hands wherever
possible. This will provide better control over
the tool help eliminate screws being driven at
an angle.
►Place the drywall screw on the screwdriver
bit. The magnetic bit holder will hold any steel
screw for easy starting.
►Press the screw against the drywall with
steady even pressure and squeeze the
variable speed trigger switch. The clutch in the
tool will engage and the screw will be driven to
the preset depth. Once fully driven, the clutch
will make a chattering sound until the variable
speed trigger is released.
►When the screw is properly driven, the screw
head will be slightly countersunk into the
drywall without breaking the outer drywall
paper. At this point, the clutch will release to
prevent over driving the screw. This will result

10
ENGLISH
in minimum work to fill the holes and taping the
seams.
►The belt clip allows you to conveniently
attached the screwdriver to your belt. This will
allow you to use both hands for positioning the
drywall.
Removing drywall screws (Fig. K)
To remove drywall screws, remove the depth stop
(1) to expose the screwdriver bit.
Notes:
a. The depth stop is a press fit onto the depth
adjuster (2). Simply twist and pull outward to
slide it off the depth adjuster.
b. You can also turn the depth adjuster clockwise
to expose the screwdriver bit. This however will
cause you to lose the depth setting and you
will have to re-set the depth.
MAINTENANCE
Keep guards, air vents and the motor housing
as clear as possible of dust and dirt. Wipe with
a clean cloth and blow through with a low-pressure
air supply. Excessive build-up of metal dust can
cause tracking of electrical current from the internal
parts to exposed metal parts.
Warning! When servicing, use only identical
replacement parts. The use of any other part may
create a hazard or cause product damage.
►DO NOT use solvents when cleaning plastic
parts. Plastics are susceptible to damage from
various types of commercial solvents and may
be damaged by their use. Use a clean cloth to
remove dirt, dust, oil, grease etc.
Warning! Do not allow brake fluids, gasoline,
petroleum-based products, penetrating oils, etc. to
come into contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
►Remove accumulated dust and debris regularly
using a SOFT and DRY brush.
Warning! Use safety goggles when using an
air jet to blow dust out of the tool. Keep air vents
clean and unobstructed to allow maximum airflow
through the tool.
►DO NOT abuse power tools. Abusive practices
can damage the tool and the workpiece.
Warning! DO NOT attempt to modify tools
or create accessories. Any such alteration
or modification is misuse and could result in
a hazardous condition leading to possible serious
injury. It will also void the warranty.
LUBRICATION
All of the bearings in this tool are lubricated with
a sufficient amount of high-grade lubricant for the
life of the unit under normal conditions. Therefore,
no further lubrication is required.
CLEANING
Use only mild soap and a slightly damp cloth to
clean your angle grinder. Many household cleaners
contain chemicals which could seriously damage
the plastic. Also, do not use petrol, turpentine,
lacquer or paint thinners or similar products. Never
let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Important! To assure product SAFETY
and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual)
should be performed by authorized service centers
or other qualified service personnel, always using
identical replacement parts.
PROTECTING THE ENVIRONMENT
Separate collection. This product
must not be disposed of with normal
household waste.
Should you find one day that your
Вlack & Decker product needs
replacement, or if it is of no further use to
you, do not dispose of it with household
waste. Make this product available for
separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again.
Re-use of recycled materials helps
prevent environmental pollution and
reduces the demand for raw materials.
Local regulations may provide for
separate collection of electrical products
from the household, at municipal
waste sites or by the retailer when you
purchase a new product.
SERVICE INFORMATION
Вlack & Decker offers a full network of company-
owned and authorized service locations. All
Вlack & Decker Service Centers are staffed with
trained personnel to provide customers with
efficient and reliable power tool service. For
more information about our authorized service
centers and if you need technical advice, repair,
or genuine factory replacement parts, contact the
Вlack & Decker location nearest you, or visit us at
www.BlackandDecker-la.com