Black & Decker GLC1423L User manual

www.blackanddecker.co.nz
www.blackanddecker.com.au
GLC1423L
GLC1823L
GLC1825L

2
C
E
B
A
D
F

3
GH
I
K
J
L

4
MN
OP

5
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER trimmer has been designed for
spaces. This appliance is intended for consumer use only.
Safety instructions
Warning! When using mains-powered appliances, basic
safety precautions, including the following, should always be
injury and material damage.
Warning! When using the machine the safety rules must be
followed. For your own safety and bystanders please read
these instructions before operating the machine. Please keep
the instructions safe for later use.
uRead all of this manual carefully before operating the
appliance.
uThe intended use is described in this manual. The use of
any accessory or attachment or the performance of any
operation with this appliance other than those
recommended in this instruction manual may present a
risk of personal injury.
uRetain this manual for future reference.
Using your appliance
Always take care when using the appliance.
uAlways use safety glasses or goggles.
uNever allow children or people unfamiliar with the
instructions to use the appliance.
uDo not allow children or animals to come near the work
area or to touch the appliance or power supply cord.
uClose supervision is necessary when the appliance is
used near children.
u
persons without supervision.
uThis appliance is not to be used as a toy.
u
uUse in a dry location only. Do not allow the appliance to
become wet.
uDo not immerse the appliance in water.
uDo not open the body casing. There are not user-
serviceable parts inside.
uDo not operate the appliance in explosive atmospheres,
dust.
uTo reduce the risk of damage to plugs or cords, never pull
the cable to remove the plug from a socket.
Safety of others
uThis appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
uChildren must be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving
parts.
uInjuries caused when changing any parts, blades or
accessories.
uInjuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
After use
uWhen not in use, the appliance should be stored in a dry,
well ventilated place out of reach of children.
uChildren should not have access to stored appliances.
uWhen the appliance is stored or transported in a vehicle it
should be placed in the boot or restrained to prevent
movement following sudden changes in speed or
direction.
Inspection and repairs
uBefore use, check the appliance for damaged or defective
parts. Check for breakage of parts and any other
conditions that may affect its operation.
uDo not use the appliance if any part is damaged or
defective.
uHave any damaged or defective parts repaired or replaced
by an authorised repair agent.
uNever attempt to remove or replace any parts other than

6
ENGLISH (Original instructions)
Additional safety instructions for grass trimmers
Warning! Cutting elements continue to rotate after the motor
is switched off.
uBe familiar with the controls and the proper use of the
appliance.
uBefore use, check the power supply cord and extension
cord for signs of damage, ageing and wear. If a cord
becomes damaged during use, disconnect the cord from
the mains supply immediately. DO NOT TOUCH THE
CORD BEFORE DISCONNECTING THE SUPPLY.
uDo not use the appliance if the cords are damaged or
worn.
uWear stout shoes or boots to protect your feet.
uWear long trousers to protect your legs.
uBefore using the appliance, check that your cutting path is
free from sticks, stones, wire and any other obstacles.
uOnly use the appliance in the upright position, with the
cutting line near the ground. Never switch the appliance
on in any other position.
uMove slowly when using the appliance. Be aware that
freshly cut grass is damp and slippery.
uDo not work on steep slopes. Work across the face of
slopes, not up and down.
uNever cross gravel paths or roads while the appliance is
running.
uNever touch the cutting line while the appliance is running.
uDo not put the appliance down until the cutting line has
come to a complete standstill.
uUse only the appropriate type of cutting line. Never use
uBe careful not to touch the line trimming blade.
uTake care to keep the mains cable away from the cutting
line. Always be aware of the position of the cable.
uKeep hands and feet away from the cutting line at all
times, especially when switching on the motor.
uBefore using the appliance and after any impact, check for
signs of wear or damage and repair as necessary.
uNever operate the appliance with damaged guards or
without guards in place.
u
always return the machine to its normal operating position
before switching on.
uAlways ensure that the ventilation slots are kept clear of
debris.
uDo not use the lawn trimmer (edge trimmer), if the cords
are damaged or worn.
uKeep extension cords away from cutting elements.
Labels on appliance
The following warning symbols are found on the appliance:
Read the manual prior to operation.
Wear safety glasses or goggles when operating
this appliance.
NWear suitable ear protectors when operating this
appliance.
Kfrom the cutting area.
RDo not expose the appliance to rain or high
humidity.
96 Directive 2000/14/EC guaranteed sound power.
Additional safety instructions for batteries and
chargers
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
6

Chargers
uUse your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
uNever attempt to charge non-rechargeable batteries.
uHave defective cords replaced immediately.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
$The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
#Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
uIf the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This appliance includes some or all of the following features.
1. On/off switch
2. Handle
3. Lock off button
4. Battery
5. Second handle
6. Guard
7. Spool housing
8. Head
9. Edge guide
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
uRemove the screw from the guard.
uKeeping the guard (6) square to the strimmer head (8)
slide it into place until the retaining tab clicks into place
(Ensure that the guide rails (10) on the guard (6) are
correctly aligned with the guide rails (11) on the strimmer
uSecure the guard (6) with the screw (12).
Warning! Never use the tool unless the guard is properly
uPress in and hold both of the buttons (14) on the side of
the handle.
uSlide the second handle (5) in place over the buttons (14).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the position of the secondary handle
The second handle (5) can be adjusted to provide optimum
balance and comfort.
uPress in the button (15) on the left side od the handle.
uRotate the second handle (5) into the required position.
uRelease the button (15).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height. There are multiple height settings.
To adjust the height setting, proceed as follows:
uDisconnect the tool from the supply.
uLoosen the adjustment collar (16) by turning it clockwise.
uGently pull the tube (17) in or out of the handle (2) to the
desired height.
uTighten the adjustment collar (16) by turning anti-
clockwise.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
Warning! Before assembly, remove the battery from the tool.
uRemove the tape holding the cutting line to the spool
housing (7).
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
uTo remove the battery, push the release button (19) while
at the same time pulling the battery out of the receptacle.
7
ENGLISH
(Original instructions)

8
ENGLISH (Original instructions)
Use
Warning! Let the tool work at its own pace. Do not overload.
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell
temperature warms up or cools down.
uTo charge the battery (4), insert it into the charger (19).
force. Be sure that the battery is fully seated in the
charger.
uPlug in the charger and switch on at the mains.
The charging indicator (20) will blink.
The charge is complete when the charging indicator (20)
switches to continuously on. The charger and the battery can
charger occasionally tops up the battery charge.
uCharge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
pack fresh and fully charged.
Setting the tool to trimming or edging mode
edging mode to trim overhanging grass along lawn edges and
For trimming, the trimmer head should be in the position
uDisconnect the tool from the supply.
uLoosen the adjustment collar (6) by turning it clockwise.
uWhilst holding the handle (2), rotate the head (8)
clockwise.
uTighten the collar (6) by turning it anti-clockwise.
uSlide the edge guide (9) into the motor housing.
Note: Note: The head will only rotate in one direction.
For edging, the trimmer head should be in the position shown
uDisconnect the tool from the supply.
uLoosen the adjustment collar (6) by turning it clockwise.
uWhilst holding the handle (2), rotate the head (8)
anti-clockwise.
uTighten the collar (6) by turning it anti-clockwise.
uSlide the edge guide out of the motor housing. Ensure that
the edging guide (9) is fully extended, an audible click will
be heard.
Note: The head will only rotate in one direction.
Switching on and off
uTo switch the tool on, press in and hold the lock off button
(3) then squeeze the trigger lever (1). Once the tool is
running you may release the lock off button (3).
uTo switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
uIn order to achieve optimum cutting results, only cut dry
grass.
Trimming
u
uGently swing the trimmer from side to side.
uWhen cutting long grass, work in stages from the top. Take
small cuts.
uKeep the tool away from hard objects and delicate plants.
uCutting line will wear faster and require more feeding if the
cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
uIf the tool starts running slowly, reduce the load.
Edging
Optimum cutting results are achieved on edges deeper than
50 mm.
uDo not use the tool to create edges. To create edges,
use an edging spade.
u
uTo make a closer cut, slightly tilt the tool.
Replacement spools of cutting line are available from your
BLACK+DECKER dealer (cat. no. A6481-XJ).
uUnplug the tool.
uKeep the tabs (21) depressed and remove the spool cover
(22) from the housing (7).
6
8

uRemove the empty spool (23) from the housing.
uRemove any dirt and grass from the spool cover and
housing.
uTake the new spool and push it onto the boss in the
housing. Rotate the spool slightly until it is seated.
uUnclip the end of the cutting line and guide the line into
the eyelet (24). The line should protrude approx. 11 cm
from the spool cover.
uAlign the tabs (21) on the spool cover with the cut outs
(25) in the housing.
uPush the cover onto the housing until it snaps securely
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (26), cut them off so that they just reach the blade.
You may wind new cutting line onto an empty spool.
uRemove the empty spool from the tool as described
above.
uRemove any remaining cutting line from the spool.
uFeed 2 cm of cutting line into the hole (27) in the spool as
uBend the cutting line and anchor it in the L-shaped slot
(28).
uWind the cutting line onto the spool in the direction of the
arrow. Make sure to wind the line on neatly and in layers.
uWhen the wound cutting line reaches the recesses (29),
cut the line. Let the line protrude approx. 12 cm from the
O).
u
Warning! Only use the appropriate type of BLACK+DECKER
cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
uCheck that the spool housing can rotate freely. Carefully
clean it if necessary.
uCheck that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
uKeep the tabs depressed and remove the spool cover
from the housing.
uPull the cutting line until it protrudes 11 cm from the
install a new spool of cutting line as instructed above.
uAlign the tabs on the spool cover with the cut outs in the
housing.
uPush the cover onto the housing until it snaps securely
into place.
uIf the cutting line protrudes beyond the trimming blade, cut
it off so that it just reaches the blade.
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
uCarefully clean the spool cover and housing.
uRemove the spool and check if the lever can move freely.
uRemove the spool and unwind the cutting line, then wind it
on neatly again as described above. Replace the spool as
instructed.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
uSwitch off and unplug the appliance/tool.
uOr switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
uOr run the battery down completely if it is integral and then
switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
uRegularly clean the cutting line and spool using a soft
brush or dry cloth.
uRegularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
ZSeparate collection. This product must not be
disposed of with normal household waste.
9
ENGLISH
(Original instructions)

10
ENGLISH (Original instructions)
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
zSeparate collection of used products and
packaging allows materials to be recycled and
used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and
recycling of BLACK+DECKER products once they have
reached the end of their working life. To take advantage of this
service please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
address indicated in this manual. Alternatively, a list of
authorised BLACK+DECKER repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com
Batteries
ZAt the end of their useful life, discard batteries with
due care for our environment:
uRun the battery down completely, then remove it from the
tool.
uNiCd, NiMH and Li-Ion batteries are recyclable. Place the
battery(s) in a suitable packaging to ensure that the
terminals cannot be short-circuited. Take them to any
authorised repair agent or a local recycling station.
uDo not short-circuit the battery terminals.
u
in a risk of personal injury or an Explosion.
Technical data
GLC1423L
H 1
GLC1825L
H 1
GLC1823L
H 1
Input Voltage
VAC 14.4 18
No-Load Speed
min-1
7100 7400
Cutting width
cm
23 25
Weight
kg
1.3
18
7400
23
1.41.5
Hand/arm weighted vibration value according to EN 786:
= 8.03 m/s2, uncertainty (K) = 1.5 m/s2.
LPA (sound preasure) 75 dB(A)
uncertainty (K) = 4 dB(A)
6
10

90623375 04/2015
Australia & New Zealand
Stanley Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.[phone] (Aust) or Tel. [phone] (NZ)