Black & Decker Dustbuster Flexi PD1800EL-XE User manual

Australia
New Zealand
www.blackanddecker.com.au
PD1800EL-XE

2
A B
C D
E F

3
ENGLISH
(Original instructions)
Intended use
Your Black & Decker Dustbuster FlexiTM vacuum cleaner has
been designed for dry vacuum cleaning purposes. This
appliance is intended for household use only.
Safety instructions
The following symbols are shown on the tool:
Warning! To reduce the risk of injury, user must
read the instruction manual.
General power tool safety warnings
@Warning! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
re and/or serious injury..
uRead all of this manual carefully before using the appli-
ance.
uThe intended use is described in this manual. The use of
any accessory or attachment or the performance of any
operation with this appliance other than those recom-
mended in this instruction manual may present a risk of
personal injury.
uRetain this manual for future reference.
Save all warnings and instructions for future refer-
ence. The term "power tool" in all of the warnings
listed below refers to your mains operated (corded)
power tool or battery operated (cordless) power
tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the inuence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
:

4
ENGLISH (Original instructions)
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b. Recommendation that the tool always be supplied via
residual current device with a rated residual current of
30mA or less.
Using your appliance
uDo not use the appliance to pick up liquids or any materi-
als that could catch re.
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to disconnect the charger from
the socket. Keep the charger lead away from heat, oil and
sharp edges.
u This appliance is not intended for use by young or inrm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
After use
uUnplug the charger before cleaning the charger or charg-
ing base.
uWhen not in use, the appliance should be stored in a dry
place.
uChildren should not have access to stored appliances.
Inspection and repairs
uBefore use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
uDo not use the appliance if any part is damaged or defec-
tive.
uHave any damaged or defective parts repaired or replaced
by an authorized repair agent.
uRegularly check the charger lead for damage. Replace the
charger if the lead is damaged or defective.
uNever attempt to remove or replace any parts other than
those specied in this manual.
Additional safety instructions - batteries and charg-
ers
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not expose the battery to heat.
uDo not store in locations where the temperature may
exceed 40°C.
uCharge only at ambient temperatures between 10°C and
40°C.
uCharge only using the charger provided with the appli-
ance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u Do not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and re.
uDo not charge damaged batteries.
uUnder extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
uIn case of skin or eye contact, follow the instructions
below.
Warning! The battery uid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Chargers
Your charger has been designed for a specic voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
uUse your Black & Decker charger only to charge the bat-

5
ENGLISH
(Original instructions)
tery in the appliance/tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
uNever attempt to charge nonrechargeable batteries.
uIf the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
u The appliance/tool/battery must be placed in a well venti-
lated area when charging.
Safety of others
uThis appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing the use of the appliance by a person responsible for
their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving
parts.
uInjuries caused when changing any parts, blades or
accessories.
uInjuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Electrical safety
Your charger has been designed for a specic voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the charger unit with
a regular mains plug.
Symbols on the charger
#This tool is double insulated; therefore no earth wire is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
$The charging base is intended for indoor use only.
Features
This appliance includes some or all of the following features.
1. On/off power switch
2. Removable hose/handle
3. Locking ring
4. Hose
5. Filter cleaning wheel
6. Transparent door
7. LED charging indicator
8. Door latch
9. 2-in-1 combi nozzle accessory
10. Accessory clip
11. Charging base
Fig. A & B
12. Pet brush
13. Crevice tool
Assembly
Mounting accessories (g. A, B & C)
The 2-in-1 combi nozzle (9) has a brush that can be folded
forward for dusting and upholstery cleaning.
The crevice tool (13) allows for vacuuming in narrow and hard
to-reach places.
The pet brush head (12) is ideal for picking up pet hairs from
cushions and furniture.
u To t an accessory press the accessory clip (10) and slide
the accessory onto the handle (2).
uTo remove an accessory, press the accessory clip (10)
and remove the accessory.
When not in use, accessories can be stored on the charger
base (11).
The handle (2) can be removed from the hose (4) allowing the
accessories (9, 12 or 13) to be connected directly to the hose
cuff (14) when required.
To remove the handle:
uUnclip the handle (2) from the appliance.
uRotate the locking ring (3) anti-clockwise to release the
clips.
uPull the hose (4) away from the handle (2).
uFit the accessory directly to the hose cuff (14).

6
ENGLISH (Original instructions)
To ret the handle:
uRemove the accessory from the hose.
uPush the hose (4) into the handle (2). Rotate the locking
ring (3) clockwise until it clicks into place.
Use
uBefore rst use, the battery must be charged.
uPlace the appliance on the charging base whenever it is
not in use.
Charging the battery (Fig. D)
uPlace the appliance on the charging base (11)
uPlug in the charger. Switch on at the mains. The charging
indicator (7) will ash continuously (slowly)
uLeave the appliance to charge.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indenitely. The charging
indicator (7) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
The charge is complete when the charging indicator (7) lights
continuously. The charger and the battery can be left connect-
ed indenitely with the LED illuminated. The LED will change
to ashing (charging) state as the charger occasionally tops
off the battery charge. The charging indicator (7) will be lit as
long as the battery is connected to the plugged-in charger.
uCharge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
Battery diagnostics
If the appliance detects a weak battery, the charging indica-
tor (3) will ash at a fast rate when the power button (1) is
activated. Proceed as follows:
uPlace the appliance on the charging base (11)
uPlug in the charger. Switch on at the mains.
uLeave the appliance to charge.
If the appliance detects a damaged battery, the charging
indicator (7) will ash at a fast rate when the appliance is on
the charger base. Proceed as follows:
uTake the appliance and the charger to be tested at an
authorised services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink, fast and slow, one
ash at each speed and repeat.
Switching on and off
u To switch the appliance on, slide the on/off power switch
(1) to the right to position 1.
u To switch the appliance off, slide the on/off power switch
(1) to the left until it clicks into the off position.
Vacuuming
uWhen operating the appliance, make sure that the hose is
not trapped, twisted or blocked.
uThe handle (2) can be easily removed from the appliance
allowing you to reach up to 1.5 m from the appliance.
uWith the handle (2) removed, the appliance can be carried
using the built-in handle.
uThe handle (2) can also be removed from the hose (4) so
that you can connect an accessory directly to the hose
cuff (14) when required.
Hints for optimum use
uWhen vacuuming stairs, always start at the bottom and
work your way up.
Optimising the suction force
In order to keep the suction force optimised, the lters must be
cleared regularly during use.
u Turn the lter cleaning wheel (5) two turns clockwise to
remove out any dust from the lters.
u The ne particulate lter must be cleaned regularly, see
“Cleaning the ne particulate lter” section.
Cleaning and maintenance
Emptying the dust container (g.E)
The dust container must be emptied regularly, preferably after
every use.
uRelease the door catch (8) and open the transparent door
(6) 180°C until it clicks in the open position.
u Remove the pre-lter (15).
uEmpty the dust container.
u Clean the pre-lter (15) by lightly shaking over a dustbin.
u Ret the pre-lter (15).
uClose the transparent door (6) and make sure that it clicks
into place.
Warning! Do not, under any circumstances, rinse out the dust
container.
Warning! Do not imerse the appliance in water. A damp cloth
and soapy water should be used to clean the exterior of the

7
ENGLISH
(Original instructions)
appliance. Always make sure that the appliance is completely
dry before re-use or storing.
Cleaning the ne particulate lter (g.F)
The ne particulate lter (16) prevents particles and larger
objects from entering the motor housing.
The lter (16) is re-usable and should be cleaned regularly.
u Remove the pre-lter (15) from the appliance as described
above.
u Remove the ne particulate lter (16) by pulling rmly.
u Tap the lter vigorously to remove loose dust from the
lter.
u If necessary, wash the lter in warm, soapy water.
u Make sure that the lters are dry.
u Ret the ne particulate lter (16) on to the appliance.
u Ret the pre-lter (15) as described above.
Replacing the lters
The lters should be replaced every 6 to 9 months and when-
ever worn or damaged. Replacement lters are available from
your Black & Decker dealer (cat. no. PD10):
u Remove the old lters as described above.
u Fit the new lters as described above.
Protecting the environment
ZSeparate collection. This product must not be disposed of with normal household waste.
Should you nd one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
zSeparate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker ofce at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Batteries
ZBlack and Decker batteries can be recharged many times. At the end of their useful life, discard batteries
with due care for our environment.:
If you want to dispose of the product yourself, the battery must
be removed as described below and disposed of in accord-
ance with local regulations.
uDischarge the battery by operating the appliance until the
motor stops.
uInvert the appliance to get access to the screws that at-
tach the base.
uRemove the 4 screws.
uRemove the base.
uDisconnect the 3-pin connector.
uPlace the battery in suitable packaging to ensure that the
terminals cannot be short-circuited.
uTake the battery to your service agent or to a local recy-
cling station.
Once removed, the battery can not be retted.
Statutory Warranties:
Our goods come with guarantees that cannot be excluded
under Australian Consumer Law. You are entitled to a replace-
ment or refund for a major failure and compensation for any
other loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable qual-
ity and the failure does not amount to a major failure.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker ofce at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.com.au to regis-
ter your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
at www.blackanddecker.com.au

8
Technical data
PD1800EL-XE
(H1)
Voltage Vdc
18
Battery Type
Li-Ion
Weight kg
1.62
Charger
CHA010014S
Input voltage Vac
120 - 240
Output voltage Vdc
23
Current mA
400
Approximate
charge time
h
4
Weight kg 0.32
Australia & New Zealand
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia
Tel.[phone] (Aust) or Tel. [phone] (NZ)
90586838 05/12