8
ENGLISH (Original instructions)
uFor increased power, slide the variable power switch (2)
forward.
Note: The oor brush (8) will power on when it is
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklights on the front of the oor head will illuminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note: The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON.
u To switch OFF, press the On/Off button (1).
uReturn the battery to the charger immediately after use so
that it will be ready and fully charged for the next use.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
u2 in 1 Accesssory tool (10)
uCrevice tool (11).
uPet hair tool (13).
uWide mouth dust brush (14).
uThe accessory tool (10), (11), (13) or (14) can be tted
either directly to the extension tube (6) or to the vacuum
inlet (5) as shown in Fig. G.
uAlign the top of the accessory tool (10), (11), (13) or (14)
with the vacuum inlet (16) or extension tube connection
(9a) and push into place so it locks into position as shown
in gure G.
Cleaning and emptying the vacuum
Filter agitator (Fig. H)
With the lift away dust canister (6) off the chassis (17) ,
rotate the lter agitator wheel 5 - 10 times to remove exces-
sive dust from the lter thus increasing its performance.
Note: It is recommended that you agitate when the unit is
emptied and the prelter removed.
Note: Maximum dust collection will only be obtained with
clean lters and an empty dust canister.
If dust begins to fall back out of the product after it is switched
off, this indicates that the dust canister is full and requires
emptying.
To empty the dust canister (Fig. I, J)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a dust bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
u Close the dust canister lid (7), until it “clicks” rmly
into position.
uInstall the lift away dust canister (6) back onto the
chassis (17).
Removing pre-lter (Fig. K)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a trash bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
u Use your index nger and thumb to pinch the pre-lter
(18), pull the pre-lter (18 ) from the dust canister (6) as
shown in gure K.
Note: The lter housing ts snuggly in the dust canister
and may be difcult to remove at rst.
uEmpty the dust canister.
u Install the pre-lter (18) into the dust canister (6)
ensuring the dust canister tab (20) aligns with the prelter
slot (19) as shown in gure K.
uInstall the dust canister onto the vacuum, until it “clicks”
rmly into position.
Removing lter (Fig. L)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a trash bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uGrasp the agitator wheel housing (21) and pull up
to remove.
u Remove the lter (22), from the agitator wheel housing
(21) as shown in gure L.
u Shake off or lightly brush any loose dust from the lter.
u Install the the lter (22), into the agitator wheel
housing (21).
uInstall the agitator wheel housing (21) onto the dust
canister, until it “clicks” rmly into position.
Cleaning the lters
u Once the lter and pre-lter are removed from the dust
canister shake off or lightly brush any loose dust from
the pre-lter and lter.
uRinse out the dust canister (6) with warm soapy water.
u Wash the lters with warm soapy water.
u Ensure the lters are completely dry before retting
(24hrs).
u Follow instructions in the “Removing pre-lter and
Removing lter” sections for assembly instructions.
Note: Maximum dust collection will only be obtained with
clean lters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full
and requires emptying or that there is a blockage somewhere.
u Wash the lters regularly using warm, soapy water and
ensure that they are completely dry before using again.
The cleaner the lter is, the better the product will perform.
