BLACK DECKER BHFEV182C User manual

BHFEV182B
BHFEV182C
BHFEV182CP
www.blackanddecker.com.au
www.blackanddecker.co.nz

23
3a
16
7
8
9
10
13
14
11
1
2
2a
4
5a5
6
12
15
17
3

3
23
5a
4
45
A
4
B
9
8
16
C
17
8
D
9a11
11 1716 E
3a
16
7
8
9
10
13
14
11
1
2
2a
4
5a5
6
12
15
17
3
4 in 1
1
2
3
4

4
1
3
2 2a 3a 16
9a
11
11
F G
67
17 I
67
6a
J
18 19
6
20
K
6
17
H

5
ENGLISH
(Original instructions)
2324
8
6
21
22
L
Intended use
Your BLACK+DECKER BHFEV182B, BHFEV182C,
BHFEV182CP 4 in 1 cordless vacuum cleaners have been
designed for vacuum cleaning purposes. These appliances
are intended for household use only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
M
Failure to follow the warnings
and instructions listed below may
result in electric shock, re and/or
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
catch re.
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
5a
N

6
ENGLISH (Original instructions)
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance.
Cleaning and user maintenance shall
not be made by children without
supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
any parts other than those specied in
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.

7
ENGLISH
(Original instructions)
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
+Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
BHFEV182B, BHFEV182C, BHFEV182CP
use charger S010**2400040 /
SSC-250040**
Features
This tool includes some or all of the following features.
1. On/Off button
2. 3 speed power switch
2a. Beater bar activation button
3. State of charge indicator
3a. Filter sense
S010Q 23
S010**2400040 /
SSC-250040**
4. 18V Battery (available with units BHFEV182C,
BHFEV182CP)
5. 18V cup charger and charging station (available with units
BHFEV182C, BHFEV182CP)
6. Lift away dust canister with lter agitator
7. Dust canister door
8. Floor head
9. Extension tube
10. 2 in 1 Accesssory tool (available to order through service
department)
11. Crevice tool (available with units BHFEV182B,
BHFEV182C, BHFEV182CP)
12. Accessory storage clip
13. Pet hair tool (available with units BHFEV182CP)
14. Wide mouth dust brush (available available to order
through service department)
15. Charge port
Charging a Battery
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
Note: To ensure maximum performance and life of lithium
ion battery packs:
uCharge the battery pack fully before rst use.
uRecharge discharged batteries as soon as possible
after every use.
uDo not discharge batteries fully.
The supplied charger offers three possible ways to charge
your battery.
1. Standard cup charging only
2. Wall mounted cup charging
3. Wall mounted suspended charging
1. Standard cup charging (Fig. A)
uPlug the charger (5) into an appropriate outlet before
inserting the battery pack (4).
uInsert the battery pack into the cup charger.
uWhen using the the cup charger a green LED will ash
indicating that the battery is being charged.
uThe completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
uThe cup charger can be inserted into the charging station
(5a) as shown in gure A.
2. Wall mounted battery charging
uMark the location of the charging station (5a) screw holes
on the wall (within reach of an electrical outlet) for
charging the vacuum while it is on the charging station.
uFix the charging station (5a) to the wall using
appropriate screws and plugs for the type of wall, and
weight of the appliance.
uInstall the cup charger (5) into the charging station (5a).
Ensure it is locked into place before proceeding.

8
ENGLISH (Original instructions)
Note: To remove the cup charger from the charging
base pull out on the retaining tabs and lift the cup
charger out.
uPlug the charger into an appropriate outlet before
inserting the battery pack.
uSlide the battery pack onto the charging station.
3. Wall mounted vacuum storage and battery
charging
The product can be attached to a wall to provide a
convenient storage and charging point for the appliance.
When mounting to a wall, make sure the mounting method
is suitable for the wall type and is appropriate to the weight
of the appliance.
uMark the location of the charging station screw holes on
the wall (within reach of an electrical outlet for charging
the vacuum while it is on the charging station.
uFix the charging station to the wall using appropriate
screws and plugs for the type of wall, and weight of the
appliance.
uInstall the cup charger into the charging station. Ensure
it is locked into place before proceeding.
Note: To remove the cup charger from the charging base pull
out on the retaining tabs and lift the cup charger out.
uPlug the charger into an appropriate outlet.
uWith the battery installed on the vacuum, slide the charge
port (15), located on the vacuum base, onto the
rails of the charging station (5a).
uThe white LED (3) on the vacuum will ash indicating that
the battery is being charged.
uThe LED sections increase as the battery is charged -
when fully charged the LEDS go out. The pack is fully
charged and may be used at this time or left on the
charger.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indenitely. The charger will keep
the battery pack fresh and fully charged.
To install battery pack (g. B)
uInsert battery (4) into tool until an audible click is heard as
shown in gure B.
uEnsure battery pack is fully seated and fully latched into
position.
To remove battery pack
uDepress the battery release button and pull battery pack
(4) out of the tool.
Assembly (Fig. C)
uAlign the top of the extension tube (9) with the vacuum
inlet (16) as shown in gure C.
uPush the extension tube (9) onto the vacuum inlet (16) so
it locks into position.
uAlign the bottom of the extension tube (9) with the oor
head (8) as shown in gure C.
uPush the bottom of the extension tube (9) onto the oor
head (8) so it locks into position.
uTo remove an accessory, press the accessory release
latch located on the accessory and pull it off.
USE
This vacuum cleaner can be used in one of four ways.
uWith the extension tube (9) and the oor brush (8) as
shown in gure C.
uWith the oor brush (8) and the vacuum inlet (16) as
shown in gure D.
uWith the extension tube (9) and an accesssory tool (10),
(11), (13) or (14) as shown in gure E.
uWith an accesssory tool (10), (11), (13) or (14) and the
vacuum inlet (16) as shown in gure E.
uAccessories not supplied with your unit can be ordered
through service department.
Switching ON and OFF (Fig. F)
uTo switch ON, press the On/Off button (1).
uFor increased power, slide the variable power switch (2)
forward.
Note: The oor brush (8) will power on when it is
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklights on the front of the oor head will illuminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note: The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON or during the charging
process.
uTo switch OFF, press the On/Off button (1).
uReturn the product to the charger immediately after use
so that it will be ready and fully charged for the next use.
Ensure that the product is fully engaged with the charger
plug.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
u2 in 1 Accesssory tool (10)
uCrevice tool (11).
uPet hair tool (13).
uWide mouth dust brush (14).
uThe accessory tool (10), (11), (13) or (14) can be tted
either directly to the extension tube ( 6 ) or to the vacuum
inlet (5) as shown in Fig. J.
uAlign the top of the accessory tool (10), (11), (13) or (14)
with the vacuum inlet (16) or extension tube connection
(9a) and push into place so it locks into position as shown
in gure G.

9
ENGLISH
(Original instructions)
14 Wide mouth dust brush
BHFEV182B
BHFE
V182C
BHFEV
182CP
10 2 in 1 Accessory
11 Crevice tool √√√
12 Accessory storage clip √√√
13 Pet hair tool √
uAll available through service department
Cleaning and emptying the vacuum
Filter sense
Whenever a lter is Blocked and needs cleaning, the red
lter LED (3) in the chassis will illuminate.
Filter agitator (Fig. H)
With the lift away dust canister (6) off the chassis (17) ,
rotate the lter agitator wheel 5 - 10 times to remove exces-
sive dust from the lter thus increasing its performance.
Note: It is recommended that you agitate when the unit is
emptied and the prelter removed.
Note: Maximum dust collection will only be obtained with
clean lters and an empty dust canister.
If dust begins to fall back out of the product after it is switched
off, this indicates that the dust canister is full and requires
emptying.
To empty the dust canister (Fig. I, J)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a dust bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uClose the dust canister lid (7), until it “clicks” rmly
into position.
uInstall the lift away dust canister (6) back onto the
chassis (17).
Removing pre-lter (Fig. K)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a trash bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uUse your index nger and thumb to pinch the pre-lter
(18), pull the pre-lter (18 ) from the dust canister (6) as
shown in gure K.
Note: The lter housing ts snuggly in the dust canister
and may be difcult to remove at rst.
uEmpty the dust canister.
uInstall the pre-lter (18) into the dust canister (6)
ensuring the dust canister tab (20) aligns with the prelter
slot (19) as shown in gure K.
uInstall the dust canister onto the vacuum, until it “clicks”
rmly into position.
Removing lter (Fig. L)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a trash bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uGrasp the agitator wheel housing (21) and pull up
to remove.
uRemove the lter (22), from the agitator wheel housing
(21) as shown in gure L.
uShake off or lightly brush any loose dust from the lter.
uInstall the the lter (22), into the agitator wheel
housing (21).
uInstall the agitator wheel housing (21) onto the dust
canister, until it “clicks” rmly into position.
Cleaning the lters
uOnce the lter and pre-lter are removed from the dust
canister shake off or lightly brush any loose dust from
the pre-lter and lter.
uRinse out the dust canister (6) with warm soapy water.
uWash the lters with warm soapy water.
uEnsure the lters are completely dry (24 hrs) before
retting.
uFollow instructions in the “Removing pre-lter and
Removing lter” sections for assembly instructions.
Note: Maximum dust collection will only be obtained with
clean lters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full
and requires emptying or that there is a blockage somewhere.
uWash the lters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the lter is, the better the product will perform.
uIt is very important that the lters are completely dry
and correctly in position before use.
Removing and clearing the rotary brushes
(Fig. M)
Warning! To reduce the risk of injury from moving parts,
disconnect battery before cleaning or servicing.
uTo remove the rotary brush (23) from the oor head (8)
depress the release button (24) as shown in gure M.
uLift the rotary brush from its locked position.
uThe rotary brush (23) can now be removed.
uClean the rotary brush, and reinstall. Ensure it is secured
in its locked position before operating.

10
ENGLISH (Original instructions)
Storage
The unit can be safely stored using the charging station (5a)
as shown in gure N.
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
uRemove the battery.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing, using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Replacing the filters
The lters should be replaced every 6 to 9 months and when-
ever worn or damaged.
Replacement lters are available from your BLACK+DECKER
dealer.
uRemove the old lters as described above.
uFit the new lters as described above.
Trouble shooting
Problem Possible Cause Possible solution
Unit will not start.
Battery pack not
charged.
Check battery pack
charging requirements.
Blockage.
Check oorhead tube.
Check extension tube.
Check between exten-
sion tube and bowl
Beater bar stops
working. Obstruction.
The unit is equipped
with a beater bar over-
load protection feature.
Remove and clean the
beater bar of all debris
and obstructions
Battery pack will not
charge.
Charger not plugged in.
Plug charger into a
working outlet. Refer
to Important Charging
Notes for more details.
Surrounding air
temperature too hot or
too cold
Move charger and
battery pack to a
4 °C or below +40 °C.
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
BHFEV182B* BHFEV182C BHFEV182CP
Voltage 18 18 18
Watt Hours 36 36
Weight 2.8 3.17 3.23
Battery BL2018 BL2018
Charger S010**2400040 /
SSC-250040** S010**2400040 / SSC-250040** S010**2400040 / SSC-250040**
Approx charge
time 5h 5h
* BHFEV182B is a bare unit and does not come supplied with
a battery or a charger.

Australia & New Zealand
SSttanley Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.[phone] (Aust) or Tel. [phone] (NZ)

N760676 07/2019