BLACK DECKER CS1820 User manual
CS1820
www.blackanddecker.com
English XX
繁體中文
简体中文
한국어
Bahasa Indonesia
ภาษาไทย
Tiếng Việt
XX
XX
XX
XX
XX
XX
English
简体中文
繁體中文
한국어
Bahasa Indonesia
Tiếng Việt
7
11
14
18
22
26
30
2
23
1347
2
9
8
6
5
15
10
12
16
18
13
11
14
17
19
3
3
2
3
1347
2
9
8
6
5
15
10
12
16
18
13
11
14
17
19
1
A
4
4a
B
7
4
C
8
D
11
E
4
4
10
12
F
1216
17 G
18
H
5
14
13
I
5
5
19
J
6
K
620
L
21
M
N
6
ENGLISH
6
6
15
O
14
P
16
QR
7
ENGLISH
Intended use
Your BLACK+DECKER CS1820 Dustbuster®hand-held vacuum
cleaners have been designed for vacuum cleaning purposes.
These appliances are intended for household use only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions listed below may result
in electric shock, re and/or seri-
ous injury.
The intended use is described in this
manual. The use of any accessory or
attachment or the performance of any
operation with this appliance other than
those recommended in this instruction
manual may present a risk of personal injury.
Retain this manual for future reference.
Using your appliance
Do not use the appliance to pick up
liquids or any materials that could
catch fire.
Do not use the appliance near
water.
Do not immerse the appliance in
water.
Never pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
7
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1830 Dustbuster® hand-held
vacuum cleaners have been designed for vacuum cleaning
purposes. These appliances are intended for household use
only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
7
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1830 Dustbuster® hand-held
vacuum cleaners have been designed for vacuum cleaning
purposes. These appliances are intended for household use
only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall not
play with the appliance. Cleaning
and user maintenance shall not
be made by children without
supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
Do not use the appliance if any part is
damaged or defective.
Have any damaged or defective parts
repaired or replaced by an authorized
repair agent.
Regularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
Never attempt to remove or replace
any parts other than those specied in
this manual.
Additional safety instructions
After use
Unplug the charger before cleaning
the charger or charging base.
When not in use, the appliance should
be stored in a dry place.
Children should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
8
ENGLISH
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge
nonrechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
Read all of this manual carefully before using
the appliance
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B, C)
Extend the crevice tool (4) as shown in gure C, until it clicks
in place. The push in brush (7) can then be tted if required for
dusting and upholstery cleaning.
8
ENGLISH (Original instructions)
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Nozzle
3. Pull out crevice tool
4. Push in brush
5. Handle On/off power switch
5A. Brush control
6. Handle
7. Charging base
8. Chassis
8a. Chassis release button
Use
Switching on and off (Fig. A)
uTo switch on, press the on/off switch (1) located on the
handle of the Dustbuster®, or alternatively on the chassis
handle (5).
uPress the button again (1 or 5), and the unit goes to a
BOOST mode.
uTo switch off, press the on/off switch (1) or (5).
Using the pull out crevice tool (Fig. B,C)
uExtend the crevice tool (3) as shown in gure C, until
it clicks in place. The push in brush (4) can be tted if
required for dusting and upholstery cleaning.
uTo retract the crevice tool (3) press the crevice tool release
button (3a) allowing it to return to its normal position
(Fig. B).
8
ENGLISH (Original instructions)
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Nozzle
3. Pull out crevice tool
4. Push in brush
5. Handle On/off power switch
5A. Brush control
6. Handle
7. Charging base
8. Chassis
8a. Chassis release button
Use
Switching on and off (Fig. A)
uTo switch on, press the on/off switch (1) located on the
handle of the Dustbuster®, or alternatively on the chassis
handle (5).
uPress the button again (1 or 5), and the unit goes to a
BOOST mode.
uTo switch off, press the on/off switch (1) or (5).
Using the pull out crevice tool (Fig. B,C)
uExtend the crevice tool (3) as shown in gure C, until
it clicks in place. The push in brush (4) can be tted if
required for dusting and upholstery cleaning.
uTo retract the crevice tool (3) press the crevice tool release
button (3a) allowing it to return to its normal position
(Fig. B).
8
ENGLISH (Original instructions)
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Nozzle
3. Pull out crevice tool
4. Push in brush
5. Handle On/off power switch
5A. Brush control
6. Handle
7. Charging base
8. Chassis
8a. Chassis release button
Use
Switching on and off (Fig. A)
uTo switch on, press the on/off switch (1) located on the
handle of the Dustbuster®, or alternatively on the chassis
handle (5).
uPress the button again (1 or 5), and the unit goes to a
BOOST mode.
uTo switch off, press the on/off switch (1) or (5).
Using the pull out crevice tool (Fig. B,C)
uExtend the crevice tool (3) as shown in gure C, until
it clicks in place. The push in brush (4) can be tted if
required for dusting and upholstery cleaning.
uTo retract the crevice tool (3) press the crevice tool release
button (3a) allowing it to return to its normal position
(Fig. B).
8
ENGLISH (Original instructions)
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Nozzle
3. Pull out crevice tool
4. Push in brush
5. Handle On/off power switch
5A. Brush control
6. Handle
7. Charging base
8. Chassis
8a. Chassis release button
Use
Switching on and off (Fig. A)
uTo switch on, press the on/off switch (1) located on the
handle of the Dustbuster®, or alternatively on the chassis
handle (5).
uPress the button again (1 or 5), and the unit goes to a
BOOST mode.
uTo switch off, press the on/off switch (1) or (5).
Using the pull out crevice tool (Fig. B,C)
uExtend the crevice tool (3) as shown in gure C, until
it clicks in place. The push in brush (4) can be tted if
required for dusting and upholstery cleaning.
uTo retract the crevice tool (3) press the crevice tool release
button (3a) allowing it to return to its normal position
(Fig. B).
8
ENGLISH (Original instructions)
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Nozzle
3. Pull out crevice tool
4. Push in brush
5. Handle On/off power switch
5A. Brush control
6. Handle
7. Charging base
8. Chassis
8a. Chassis release button
Use
Switching on and off (Fig. A)
uTo switch on, press the on/off switch (1) located on the
handle of the Dustbuster®, or alternatively on the chassis
handle (5).
uPress the button again (1 or 5), and the unit goes to a
BOOST mode.
uTo switch off, press the on/off switch (1) or (5).
Using the pull out crevice tool (Fig. B,C)
uExtend the crevice tool (3) as shown in gure C, until
it clicks in place. The push in brush (4) can be tted if
required for dusting and upholstery cleaning.
uTo retract the crevice tool (3) press the crevice tool release
button (3a) allowing it to return to its normal position
(Fig. B).
9
ENGLISH
To retract the crevice tool (4) press the crevice tool release button
(4a) allowing it to return to its normal position (Fig. B).
Fitting the oor extension tube (Fig. D)
Slide the nozzle (3) into the oor extension tube (9) until
you hear an audible ‘click’ as shown in gure D.
The oor extension tube is supplied with a ip down brush
(11) for cleaning difcult to reach areas (Fig.E).
Fitting the oor head (Fig. F)
Slide the oor extension tube (9) onto the oor
extension head (12) until you hear an audible ‘click’ as
shown in gure F.
Floor sense feature
The appliance is tted with a unique oor sensing feature.
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars (Fig. G, H)
Depress the beater bar unit (16) release button (17) as
shown in gure G.
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
attached to the oor extension.
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning! When xing to a wall, make sure that the xing
method is suitable for the wall type and is appropriate to the
weight of the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will illuminate.
A. Filter sensor
Whenever a lter is Blocked and needs cleaning, the red
lter LED (A) in the handle will illuminate.
Clean ne dust from lter (See section on ‘cleaning lters’
in this manual).
B. LED Charging display
Battery icon (B) will illuminate when appliance requires
charging. Led display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode allow-
ing you to operate at higher power.
9
ENGLISH
(Original instructions)
Fitting the handle to the main chassis
(Fig. D, E)
uSlide the handle (6) into the main chassis (8) as shown in
gure D.
uSecure with retaining screw (17) as shown in gure E.
Fitting the Dustbuster®to the Chassis
(Fig. F, G, H)
uSlide the Dustbuster® , nozzle rst, into the chassis (8)
until an audible ‘click’ is heard as shown in gure F.
uTo release the Dustbuster®from the chassis press the
chassis release button (8a) and lift clear.
uThe appliance can now be operated via the on/off button
(5) on the handle (6) along with the ‘BOOST’ mode as
shown in gure H. This also allows you to utilise the beater
bars via the ‘brush on’ control (5A).
Removing and clearing the beater bars
(Fig. I, J)
uTo remove the beater bar unit (9) from the oor head (10)
Depress the release button (11) as shown in gure I.
uThe beater bar (12) can now be removed. The end pieces
are also removable allowing you to clear the brushes from
any hair or other debris that may have accumulated (Fig.
J).
Charging (Fig. K, L)
uPlace the appliance into the charging base (7) as shown in
gure K .
uPlug the charging port (7) into an electrical outlet.
uSwitch the electrical outlet on. The LED charging indicator
(B) will Illuminate (Fig. L).
Multi LED Display
A. Filter sensor
Whenever a lter is Blocked and needs cleaning, the red
lter LED (A) in the handle will illuminate.
Clean ne dust from lter (See section on ‘cleaning lters’
in this manual).
B. LED Charging display
Battery icon (B) will illuminate when appliance requires
charging. Led display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
LED Patterns
Charging
Battery Fault
Charger Fault
Battery Hot
Cleaning the lters (Fig. M, N, O, P, Q,
R )
uPress the dust bowl release button (13) (Fig. M)
uEject the dust bowl (14) (Fig.N)
uLift the lter assembly (15) from the dust bowl (14) (Fig.O).
uEmpty the dust bowl by lightly shaking over a dustbin
(Fig. P).
Note: The pre filter is impregnated with a fragrance allowing
for a pleasing odour to be released when the appliance is in
use.
uThe lter (16) can now be removed from the pre lter (15)
Figure Q.
uEmpty any remaining dust from the dust bowl.
uRinse out the dust-bowl with warm soapy water.
uWash the lters with warm soapy water (Fig. R).
uMake sure the lters are dry
uRet the lters onto the appliance.
uClose the dust-bowl. Make sure the release latch (13)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
A
B
C
8
ENGLISH (Original instructions)
uTo retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
Fitting the oor extension tube (Fig. D)
uSlide the nozzle (3) into the oor extension tube (9) until
you hear an audible ‘click’ as shown in gure D.
uThe oor extension tube is supplied with a ip down brush
(11) for cleaning difcult to reach areas (Fig.E).
Fitting the oor head (Fig. F)
uSlide the oor extension tube (9) onto the oor extension
head (12) until you hear an audible ‘click’ as shown in
gure F.
Floor sense feature
The appliance is tted with a unique oor sensing feature.
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
uDepress the beater bar unit (16) release button (17) as
shown in gure G.
uThe beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
attached to the oor extension.
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning! When xing to a wall, make sure that the xing
method is suitable for the wall type and is appropriate to the
weight of the appliance.
uMark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
uPlace the charger (14) into the charging port (15) and plug
into the electrical outlet.
uSwitch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
Multi LED Display
A. Filter sensor
Whenever a lter is blocked and needs cleaning, the red
lter LED (A) in the handle will illuminate.
Clean ne dust from lter (See section on ‘cleaning lters’
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
LED Patterns
Charging
Battery Fault
Charger Fault
Battery Hot
A
B
C
10
ENGLISH
Cleaning the lters (Fig. J, K, L, P, M, N)
Press the dust bowl release button (19) (Fig. J)
Eject the dust bowl (6) (Fig.K)
Lift the lter assembly (20) using the metal handle from the
dust bowl (6) (Fig.L).
Empty the dust bowl by lightly shaking over a dustbin.
The lter(21) can now be removed from the pre lter(20)
(Fig. M).
Empty any remaining dust from the dust bowl.
Rinse out the dust-bowl with warm soapy water.
Wash the lters with warm soapy water (Fig. N).
Make sure the lters are dry
Ret the lter onto the appliance.
Close the dust-bowl. Make sure the release latch (19)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does not
require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/ charger
using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do not
use any abrasive or solvent-based cleaner.
Replacing the lters
The lter should be replaced every 6 to 9 months and when
ever worn or damaged. Replacement lters are available from
your BLACK+DECKER dealer
Filters are supplied in foil packaging which needs to be
removed. To assemble lters see Fig. M
Remove the old lters as described above.
Fit the new lters as described above.
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
10
ENGLISH
(Original instructions)
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
uRun the battery down completely if it is integral and then
switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
-
your BLACK+DECKER dealer (cat. noVPF20)
reach the end of their lifespan they must be disposed of at a
local recycling centre.
Filters are supplied in foil packaging which needs to be
Warning!
Cotton linen fragrance.
Wash face, hands and any exposed skin
thoroughly after handling. Wear protective
gloves/protective clothing/eye protection/
face protection. If in eyes: Rinse cautiously
with water for several minutes. Remove
contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get
medical advice/attention. Avoid release into
the environment. Do not ingest.
u
u
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CS1830
Voltage 18V
Weight 2.8Kg
-
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
to you.
NOTE
u Black & Decker's policy is one of continuous improvement to
our products and, as such, we reserve the right to change
product specifications without prior notice.
u Standard equipment and accessories may vary by country.
u Product specifications may differ by country.
u Complete product range may not be available in all countries.
Contact your local Black & Decker dealers for range
availability.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efcient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker’s policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specications without prior notice.
Standard equipment and accessories may vary by
country.
Product specications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Charger
Input Voltage (Vac) 100-240
Output Current (mA) 400
Approx Charge Time (h) 6
9
ENGLISH
(Original instructions)
uPress the dust bowl release button (19) (Fig. J)
uEject the dust bowl (6) (Fig.K)
u
the dust bowl (6) (Fig.L).
uEmpty the dust bowl by lightly shaking over a dustbin.
Note: On unit FEJ520JFS the pre filter is impregnated with a
fragrance allowing for a pleasing odour to be released when
the appliance is in use.
u
(Fig. M).
uEmpty any remaining dust from the dust bowl.
uRinse out the dust-bowl with warm soapy water.
u
u
u
uClose the dust-bowl. Make sure the release latch (19)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
uRun the battery down completely if it is integral and then
switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
-
your BLACK+DECKER dealer (cat. noVPF20)
reach the end of their lifespan they must be disposed of at a
local recycling centre.
Filters are supplied in foil packaging which needs to be
Warning!
Cotton linen fragrance.
Wash face, hands and any exposed skin
thoroughly after handling. Wear protective
gloves/protective clothing/eye protection/
face protection. If in eyes: Rinse cautiously
with water for several minutes. Remove
contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get
medical advice/attention. Avoid release into
the environment. Do not ingest.
u
u
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CS1820
Voltage 18V
Weight 2.4Kg
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
to you.
NOTE
u Black & Decker's policy is one of continuous improvement to
our products and, as such, we reserve the right to change
product specifications without prior notice.
u Standard equipment and accessories may vary by country.
u Product specifications may differ by country.
u Complete product range may not be available in all countries.
Contact your local Black & Decker dealers for range
availability.
11
简体中文
部件名称
本工具包含如下部分或全部部件。
1. 电源开关
2. 手柄
3. 吸嘴
4. 拉出细缝吸嘴
5. LED充电指示灯
6. 集尘仓
7. 推进刷头
8. 地板伸缩释放夹
9. 地板伸缩管
10. 地板头释放夹
11. 翻转刷头
12. 地板头
13. 墙上支架
14. 充电器
15. 充电插口
使用
启动与关闭 (图 A)
按下按钮开启设备，设备会以低速、低功率模式
操作，从而延长电池使用寿命。
再次按下按钮，设备则会变为加速模式。
再次按下该按钮会关闭该产品。
使用拉出细缝吸嘴 (图 B、C)
如图C所示，延伸细缝吸嘴(4)，直到其卡入到
位。如果需要，可再安装推进刷头(7)以进行除
尘和内饰清洁。
按下细缝吸嘴释放按钮(4a)可使细缝吸嘴(4)
缩回其正常位置(图B)。
安装地板伸缩管 (图 D)
如图D所示，将吸嘴(3)滑入地板伸缩管(9)，
直到听到“咔嗒”声。
地板伸缩管包含一个翻转刷头(11)以清洁难以
清洁的区域(图E)。
安装地板头 (图 F)
如图F所示，将地板伸缩管(9)滑到地板伸缩头
(12)的上方，直到听到“咔嗒”声。
地板传感功能
该设备提供特殊的地板传感功能。它可感应到超厚
地毯，并可自动从低速变为加速模式以便更好的清
洁性能。
从打手除尘棒中取出和清洁头发
(图 G、H)
如图G所示，按下打手除尘棒设备(16)释放
按钮(17)。
现可取出打手除尘棒设备(18)。此外，也可取出
尾端件以便您清洁可能在使用中积聚的任何头发
或其它碎片(图H)。
充电中 (图 I)
该设备可单独充电或安装到地板伸缩管时充电。
壁挂式安装
该壁挂式安装(13)可以安装到墙上，以为设备提供
方便的存放地点。
警告！ 安装到墙上时，请确保安装方法适合墙壁
类型并能承受设备的重量。
标记螺丝孔的位置(在对置于墙上支架上的真空
吸尘器进行充电时电源插座可及的范围内)。
将充电器(14)置于充电插口(15)中，并插入电
源插座。
开启电源插座。LED充电指示灯(B)将亮起。
A. 过滤传感器
每当过滤器阻塞并需要清洁，手柄中的红色过滤
LED(A)将亮起。
清洁过滤器中的细微粉尘(参见本手册中的“清
洁过滤器”)。
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
多 LED 显示
12
简体中文
设计用途
BLACK+DECKERCS1820Dustbuster® 手持式吸尘器的
设计用途为真空吸尘。这些设备仅供家用。
使用设备前，请仔细阅读本手册。
安全说明
警告！ 请仔细阅读所有安全警告和说明。
如不遵守以下任何警告和说明，可能会导致
触电、火灾和/或严重伤害。
本手册描述了设备的设计用途。如果配件或附件
的使用、本设备的操作超出本手册建议的范围，
则可能出现人身伤害的危险。
请保存好本手册，以备将来查阅。
使用设备时
请不要使用本吸尘器吸水或其他液体或任何可能
会引起火灾的材料。
请不要在靠近水的地方使用本吸尘器。
请勿将设备浸入水中。
切勿猛力拉扯充电器以使充电器脱离电源。
请确保充电器远离热源、油脂及尖锐的边缘。
在有他人监督的情况下，或在接受过安全使用该
产品的指导并已了解了可能存在的危险的情况
下，8岁或以上的儿童，以及身体、感官或精神
较差的人员，或者对该类产品缺少使用经验和认
识的人员，也可以使用本设备。儿童不得耍玩本
设备。在没有他人监督的情况下，禁止儿童使用
本设备或对其进行维护保养。
检查与维修
使用前，请检查吸尘器是否受损或存在缺陷部件。
检查部件是否破裂、开关是否损坏，以及是否存在
影响设备操作的其它情况。
如果部件损坏或存在缺陷，请勿使用设备。
损坏或缺陷部件必须交由授权维修代理处维修
与更换。
定期检查充电器导线是否损坏。如导线损坏或
有缺陷，请更换充电器。
禁止试图拆卸或更换本手册规定之外的任何部件。
附加安全说明
使用后
清洁充电器或充电底座前，请拔下充电器。
不使用设备时，应存放于干燥场所。
应将设备存放在儿童接触不到的地方。
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
其他风险
使用工具时，可能出现本安全警示之外的其他剩余风
险。这些风险可能来自使用不当、使用时间过长等。
尽管遵守了相关的安全法规并采用了安全装备，某
些其他风险仍然是无法避免的。这些风险包括：
接触旋转/运动部件时所导致的伤害风险。
更换部件、锯片或配件时的伤害风险。
长期使用工具的伤害风险。长期使用任何工具
时，均应定期休息。
听力损伤。
吸入工具使用过程中产生的粉尘导致的健康危害
(例如，锯切木材，特别是橡木、山毛榉和中密
度纤维板时)。
充电器
您的充电器专门设计用于特定电压。请务必检查
电源电压是否与铭牌一致。
警告！切勿尝试使用一般的电源插头替换充电器。
只能使用随附的BLACK+DECKER充电器为设备
内的电池充电。其他非原厂电池可能会爆裂，
导致人身伤害和损害。
切勿尝试为不可再充电的电池充电。
如果电源线已损坏，必须让制造商或
BLACK+DECKER授权维修中心更换以避免发生
危险。
不要将充电器暴露在水中。
不要打开充电器。
不要刺破充电器。
充电时，设备/工具/电池必须放在通风良好的地方。
电气安全
充电器上的符号
使用设备前，请仔细阅读本手册。
本工具采用双重绝缘，因此无需接地线。
请务必检查电源电压是否与铭牌上的电压
一致。
充电底座仅供室内使用。
设备上的标签
设备上显示下列符号和日期码
使用设备前，请仔细阅读本手册
仅可与S010Q23充电器使用
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the
battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
13
简体中文
B. LED 充电显示
当设备需要充电时，电池图示将亮起。LED显
示表示充电状态(参见本手册中的LED模式图
表)。
C. 加速模式
当设备处于加速模式时亮起，可让您以高功率操
作设备。
清洁过滤器 (图 J、K、L、M 和 N)
按下集尘仓释放按钮(19)(图J)
喷出集尘仓(6)(图K)
使用金属手柄从集尘仓(6)提起过滤器组件(20)
(图L)。
在垃圾筒上方轻轻抖动，清空集尘仓。
过滤器(21)现可从预过滤器(20)中取出(图M)。
清空集尘仓上剩余的灰尘。
用温肥皂水清洗集尘仓。
用温肥皂水清洗过滤器(图N)。
确保过滤器干燥。
将过滤器重新安装到设备上。
关闭集尘仓。确保释放按钮(19)卡入到位。
警告！ 在对设备进行任何维护或清洁前，请拔下设
备插头。
经常用湿布擦拭设备。请不要使用任何研磨性或
基于溶剂的清洁剂。请不要将本吸尘器浸泡在水中
维护
BLACK+DECKER无线设备设计精良，可以长期使用，
而且只需最少的维护。要持续获得令人满意的工作
效果，需要进行合适的工具维护和定期清洁。
警告！ 对无线设备进行任何维护工作之前，必须：
如果设备配有一体式电池，请将电池电量耗尽，
然后再关闭电源。
清洁之前将充电器拔下。除了定期清洁外，
本充电器无需其他保养。
定期使用软刷或干布清洁设备/充电器内的通风槽。
定期使用湿布清洁电动机外壳。请不要使用任何
研磨性或基于溶剂的清洁剂。
更换过滤器
每6到9个月，或当过滤器磨损或损坏时，即应
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
电池温度高
LED 模式
电池故障
充电器故障
充电中
更换过滤器。BLACK+DECKER零售商均有提供滤
网备件。
过滤器包装于需取出的铝箔中。为组装过滤器，请
参看图M
按照上述说明取下旧过滤器。
按照上述说明安装新过滤器。
保护环境
分类回收。由此符号标记的产品和电池不得
与普通家庭垃圾一起处理。
产品和电池包含可恢复或回收的材料，从而降低对
原材料的需求。
请根据当地供给回收电子产品和电池。为获得更多
信息，请参看www.2helpU.com
技术参数
服务信息
Black&Decker提供覆盖整个亚洲的公司隶属和授权服
务地点。所有的Black&Decker服务中心都具有训练
有素的人员，为客户提供高效和可靠的产品服务。
不论您是需要技术建议、维修或原厂替换部件，
请联系最靠近您的Black&Decker地点。
注
Black&Decker的政策是持续改进我们的产品，
因此，我们保留随时更改产品规格的权利，
恕不另行通知。
标准设备和配件可能会因为不同的国家而有所
不同。
产品规格可能会因为不同的国家(地区)而有所
不同。
并非所有的国家都有提供完整的产品系列。
有关各产品系列的供货情况，请联系您当地的
Black&Decker代理商。
Press the dust bowl release button (19) (Fig. J)
Eject the dust bowl (6) (Fig.K)
the dust bowl (6) (Fig.L).
Empty the dust bowl by lightly shaking over a dustbin.
Note: On unit FEJ520JFS the pre filter is impregnated with a
fragrance allowing for a pleasing odour to be released when
the appliance is in use.
(Fig. M).
Empty any remaining dust from the dust bowl.
Rinse out the dust-bowl with warm soapy water.
Close the dust-bowl. Make sure the release latch (19)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
-
your BLACK+DECKER dealer (cat. noVPF20)
reach the end of their lifespan they must be disposed of at a
local recycling centre.
Filters are supplied in foil packaging which needs to be
Warning!
Cotton linen fragrance.
Wash face, hands and any exposed skin
thoroughly after handling. Wear protective
gloves/protective clothing/eye protection/
face protection. If in eyes: Rinse cautiously
with water for several minutes. Remove
contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get
medical advice/attention. Avoid release into
the environment. Do not ingest.
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CS1820
Voltage 18V
Weight 2.5Kg
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
to you.
NOTE
Black & Decker's policy is one of continuous improvement to
our products and, as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all countries.
Contact your local Black & Decker dealers for range
availability.
CS1820
电压 18伏
重量 .4千
2 克
充电器
输入电压 (Vac)100-240
输出电流 (mA) 400
大约充电时间 (h) 6
14
繁體中文
請注意! 各地區上市產品/配件不盡相同, 請依台灣繁
體中文說明書的內容為主。
Warning! Attachments and accessories are not the same in
each region, please only refer to Taiwan Traditional Chinese
description in this manual.
設計用途
您的 Black & Decker CS1820 Dustbuster® 手持式真空
吸塵器設計用於真空吸塵用途。這些工具僅供一般
家用。
操作本工具前，請仔細閱讀本手冊全部內容。
安全指示
警告！請閱讀所有安全警告及指示。
若不遵循以下所示警告及指示，可能會導致
觸電、火災及/或嚴重傷害。
器具的設計用途已在本手冊中載明。若使用並非
本使用手冊中所建議的配件或附件，或者使用本
器具執行並非本使用手冊中所建議的操作，可能
會有人身傷害的風險。
請妥善保存本手冊以備將來查閱。
使用工具
請勿使用本工具吸取任何液體或任何易燃材料。
請勿在靠近水的地方使用本工具。
請勿將本工具浸入水中。
請勿拉扯充電器引線以將充電器從插座上拔下。
讓充電器遠離熱、油和銳邊。
年滿 8 歲的兒童，以及身體、感覺或心理機能不
健全的人員或缺乏經驗及知識的人員，若在針對
安全使用本器具的監督或指示之下，並已瞭解所
涉及的危險，則可以使用本器具。兒童不得玩耍
本器具。請勿在沒有監督的情況下讓小孩對本工
具進行清潔和維護。
檢查與維修
使用前，請檢查器具是否有損壞或有故障的零件。
檢查零件破損情況以及可能影響操作的開關損壞和
任何其他狀況。
若發現任何零件已損壞或有故障，請勿使用本
工具。
將所有受損或有故障的零件送往授權的維修中心
進行維修或更換。
電動工具之修理，僅可由認證的技術人員執行。
請勿交由非百得認證服務中心的認證技術人員進行
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
修理、維護、調整。若產品經由非百得認證的維修
工程師拆解、組裝、調整，恕無法適用百得一年家
用保修條款。
為充份發揮其功能，修理、維護、調整請務必使
用原廠零件。
除了本手冊中指定的零件之外，切勿嘗試卸下任
何其他零件或對其進行替換。
額外安全指示
使用後
清潔充電器或充電底座之前先拔下充電器插頭。
不使用時，應將工具儲存在乾燥的地方。
切勿讓兒童接觸存放的器具。
殘餘風險
使用本工具時，可能會出現隨附安全警告中所不包括
的其他殘餘風險。誤用、長時間使用工具等因素會導
致這些風險。
即使遵循相關安全規定並採用安全裝置，仍然無法避
免某些殘餘風險。此類風險包括：
更換任何部件、刀片或配件時引起的傷害。
長時間使用工具引起的傷害。長時間使用任何工
具時，請確保定期休息。
聽力受損。
充電器
您的充電器設計用於特定電壓。請務必檢查主電壓
是否與銘牌一致。
警告！切勿嘗試使用一般的電源插頭取代充電器裝
置。
只能使用工具隨附的 Black & Decker 充電器為工具內
的電池充電。其他非原廠電池可能會爆裂，導致人
身傷害和損害。
切勿嘗試為不可再充電的電池充電。
若電源線損壞，必須送往製造廠商或授權的
BLACK+DECKER 服務中心更換以避免發生危險。
請勿將充電器暴露在水中。
請勿打開充電器。
請勿刺破充電器。
充電時，必須將工具/電池組置放在一個通風良好
的地方。
電氣安全
充電器上的符號
15
繁體中文
使用工具前，請仔細閱讀本手冊全部內容。
本工具採用雙重絕緣，因此無需接地線。
請務必檢查電源電壓是否與銘牌一致。
充電底座僅供室內使用。
器具上的標籤
本器具上具有以下圖示：
使用器具前，請仔細閱讀本手冊全部內容。
功能部件
本工具包括以下部分或全部功能部件
1. 電源開關
2. 手柄
3. 吸嘴
4. 拉出細縫吸嘴
5. LED 充電指示燈
6. 集塵筒
7. 毛刷頭
8. 地板延長管釋放夾
9. 地板延長管
10. 地板吸塵頭釋放夾
11. 2 合 1 毛刷頭
12. 地板吸塵頭
13. 牆面支架
14. 充電器
15. 充電埠
使用
開啟和關閉電源 (圖 A)
按下開關按鈕，本裝置將以低速、低功耗模式下
工作，延長電池的使用壽命。
再次按下該按鈕，裝置將以增加動力模式工作。
再次按下該按鈕將關閉裝置。
使用拉出細縫吸嘴 (圖 B 和 C)
如圖 C 所示延長細縫吸嘴 (4)，直至其卡到位。
如需要進行除塵和內飾清潔，即可以安裝推入
刷頭 (7)。
按下細縫吸嘴釋放按鈕 (4a) 使其返回原位，即
可縮回縫隙吸嘴 (4) (圖 B)。
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
安裝地板延長管 (圖 D)
將吸嘴 (3) 滑入地板延長管 (9)，直到聽見一聲
清晰的卡嗒聲，如圖 D 所示。
地板延長管裝配 2 合 1 毛刷頭 (11)，可用於清潔
難以接近的區域 (圖 E)。
安裝地板吸塵頭 (圖 F)
將地板延長管 (9) 滑入地板延長吸塵頭 (12)，直
到聽見一聲清晰的卡嗒聲，如圖 F 所示。
地板感應工具
本器具的電機安裝有地板感應工具。
該工具對厚地毯有所感應，將自動從低速模式調至
增加動力模式工作。智慧地板感應功能僅在低速模
式且毛刷轉動下才會啟動，從地板移至地毯使用時
會自動調整成增加動力模式；回到地板後將自動調
整成低速模式。
移除地板毛刷上的毛髮
(圖 G 和 H)
如圖 G 所示，按下地板毛刷盒 (16) 釋放按鈕
(17)。
現在即可移除地板毛刷 (18)。您也可以移除尾
端，以清潔毛髮和其他可能在使用時堆積的碎片
(圖 H)。
充電 (圖 I)
本產品可以作為單一裝置充電或安裝於牆面充電。
牆面安裝
牆面支架 (13) 可以安裝於牆面，方便儲存以及為器
具充電。
警告！安裝於牆面時，請確保安裝方式適合牆面
類型，適合器具重量。
標記螺絲洞的位置 (確保將器具置放在牆面支架
上時，附近有電源插座可充電)
將充電器 (14) 插入充電埠 (15) 然後插入電源
插座。
開啟開關。LED 充電指示燈 (B) 將亮起。
製造年份及機號(範例)
2016 23 BM
西元年份 週數 機號
16
繁體中文
A. 濾心清潔感應器
當濾心阻塞、需要清潔時，手柄上的紅色 LED
(A) 燈亮起。
清潔濾心中的微粒灰塵。 (參閱本手冊中的
「清潔濾心說明」)。
B. LED 充電指示燈
器具需要充電時，電池圖標將亮起。LED 充電
指示燈標註充電狀態 (請參閱本手冊內的 LED 模
式圖表)。
C. 增加動力模式
將在器具處於增加動力模式時亮起，將以更高功
耗工作。
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
多 LED 顯示
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
電池溫度高
LED 模式 (充飽電後 LED 燈會自動熄滅)
電池故障
充電器故障
充電中
清潔濾心 (圖 J、K、L、M 與 N)
按下集塵筒釋放按鈕 (19) (圖 J)
清空集塵筒 (6) (圖 K)
使用集塵筒 (6)上的金屬手柄，拉起濾心組件
(20) (圖 L)。
在垃圾桶上輕輕晃動，清空集塵筒或以軟毛刷
輕刷濾心。
現在即可從外濾心 (20) 移除內濾心 (21)
(圖 M)。
清空集塵筒中殘餘的塵埃。
用溫肥皂水沖洗集塵筒。
用溫肥皂水清洗濾心 (圖 N)。
確保濾心乾燥。
將過濾心重新安裝到本器具上。
關閉集塵筒。確保集塵筒釋放按鈕 (19) 卡入到位。
警告！在對工具進行任何維護或清潔前，請拔下工
具插頭。
時常用濕布擦拭工具。
請勿使用任何研磨性或溶劑型清潔劑。請勿將工具
浸入水中。
維護
您的 Black & Decker 充電式工具採用卓越的設計，能
夠長時間使用，並且只需最少的維護。
若要持續獲得滿意的操作效果，需進行正確的工具
維護和定期的清潔。
警告！在充電式工具上執行任何維護工作之前：
若電池屬於內建電池，請使電池完全放電，然後
再關閉電源。
清潔之前請拔下充電器的插頭。您的充電器除了
定期清潔之外，並不需要執行任何維護操作。
定期使用軟刷或乾布清潔工具/充電器內的通
風槽。
在電池用完電量後，建議馬上充電，鋰電池請勿
過度放電, 電力過度耗竭會導致鋰電池損壞。若
長時間未使用電池 (1 年以上) , 請每 6 個月為電
池充電一次, 以確保電池壽命。
請定期使用濕布清潔電動機外殼。請勿使用任何
研磨性或溶劑型清潔劑。
更換濾心
濾心在出現磨損或損壞時予以更換。您的BLACK+-
替換用濾心 (產品
DECKER 代理商為您提供
目錄號 VPF20S)。
保護環境
分類回收。帶有此標誌的產品和電池必須與
一般家庭廢物分開處置。
Press the dust bowl release button (19) (Fig. J)
Eject the dust bowl (6) (Fig.K)
the dust bowl (6) (Fig.L).
Empty the dust bowl by lightly shaking over a dustbin.
Note: On unit FEJ520JFS the pre filter is impregnated with a
fragrance allowing for a pleasing odour to be released when
the appliance is in use.
(Fig. M).
Empty any remaining dust from the dust bowl.
Rinse out the dust-bowl with warm soapy water.
Close the dust-bowl. Make sure the release latch (19)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
-
your BLACK+DECKER dealer (cat. noVPF20)
reach the end of their lifespan they must be disposed of at a
local recycling centre.
Filters are supplied in foil packaging which needs to be
Warning!
Cotton linen fragrance.
Wash face, hands and any exposed skin
thoroughly after handling. Wear protective
gloves/protective clothing/eye protection/
face protection. If in eyes: Rinse cautiously
with water for several minutes. Remove
contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get
medical advice/attention. Avoid release into
the environment. Do not ingest.
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CS1820
Voltage 18V
Weight 2.5Kg
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
to you.
NOTE
Black & Decker's policy is one of continuous improvement to
our products and, as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all countries.
Contact your local Black & Decker dealers for range
availability.
17
繁體中文
技術資料
服務資訊
Black & Decker 提供遍佈亞洲的公司隸屬及授權服務
地點。所有的 Black & Decker 服務中心都具有訓練有
素的人員，為客戶提供高效、可靠的產品服務。
不論您需要的是技術建議、維修服務還是原廠正品
替換部件，都可以聯絡距您最近的 Black & Decker 服
務地點。
附註
Black & Decker 秉持不斷改善產品的原則，因
此，我們保留隨時變更產品規格而不預先通知
的權利。
標準設備及配件可能視國家/地區而有所不同。
產品規格可能視國家/地區而有所不同。
並非在所有的國家/地區都將提供完整的產品系
列。如需各產品系列的供應情況，請聯絡您當地
的 Black & Decker 代理商。
進口/委製廠商:
新加坡商百得電動工具(股)公司台灣分公司
地址: 台北市士林區德行西路33號2樓
電話: 02-2834-1741
CS1820
電壓 18V
電池容量 2.0Ah
滿電使用時間 低速約 24 分, 高速約
14 分
吸力 手持最大 40AW
集塵盒容量 500ml
重量 2.4kg
充電時間 6 小時 (完全沒電)
18
한국어
용도
BLACK+DECKER CS1820 Dustbuster® 무선스틱 진공
청소기는 진공 청소용으로 설계되었습니다. 본 제품은
가정용입니다.
제품을 사용하기 전에 본 사용 설명서 전체
내용을 잘 읽고 숙지해주십시오.
안전 지침
경고! 안전 경고와 지시 사항을 모두
읽으십시오.
아래 나열된 경고와 지시 사항을 준수하지
않으면 감전, 화재 및/또는 심각한 부상을
초래할 수 있습니다.
본 사용 설명서에 제품의 용도가 설명되어
있습니다. 본 사용 설명서에서 권장하는 방식
이외의 다른 방식으로 본 제품을 조작하거나
액세서리 또는 부착물을 사용하는 경우 신체
부상의 위험이 있을 수 있습니다.
향후 참고할 수 있도록 본 사용 설명서를 잘
보관해두십시오.
제품 사용
본 제품으로 화재를 일으킬 수 있는 액체나 물질을
빨아들이지 마십시오.
본 제품을 물 근처에서 사용하지 마십시오.
본 제품을 물에 담그지 마십시오.
충전기를 소켓에서 분리할 때 절대로 충전기 리드
선을 잡아당기지 마십시오. 충전기 리드 선이
열, 오일 및 날카로운 가장자리에 닿지 않도록
하십시오.
안전 책임자의 감독 또는 제품 사용과 관련된
지시 사항이 제공되고 관련된 위험 사항을 이해한
경우에만 8세 이상의 어린이 및 신체, 지각 또는
정신 능력이 낮거나 경험 및 지식이 부족한 사람이
본 제품을 사용할 수 있습니다. 어린이가 제품을
가지고 놀게 해서는 안됩니다. 청소 및 사용자
유지 보수를 할 때 감독 없이 어린이 혼자 해서는
안됩니다.
검사 및 수리
사용 전, 제품에 손상되거나 결함 있는 부품이 있는지
점검하십시오. 부품 파손, 스위치 손상 등 정상적
사용에 영향을 미칠 수 있는 제품 이상이 있는지
점검하십시오.
손상되거나 결함 있는 부품이 있는 경우에는
제품을 사용하지 마십시오.
손상되거나 결함 있는 부품은 공인 수리 대리점에
의뢰하여 교체 또는 수리하십시오.
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER CS1820
Dustbuster® hand-held vacuum cleaners have been designed
for vacuum cleaning purposes. These appliances are intended
for household use only.
tRead all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
this manual.
Additional safety instructions
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
충전기 리드 선의 손상 여부를 주기적으로
점검하십시오. 리드 선이 손상되거나 결함이
발견되면 충전기를 교체하십시오.
본 사용 설명서에 명시된 내용 이외에는 어떤
부품도 제거하거나 교체하지 마십시오.
추가 안전 지침
사용 후
충전기 또는 충전 거치대를 청소하기 전에
충전기의 플러그를 뽑으십시오.
사용하지 않을 때에는 본 제품을 습기가 없는
건조한 장소에 보관해야 합니다.
어린이가 보관된 제품을 만지지 못하도록 해야
합니다.
충전기
본 충전기는 특정 전압에서 작동하도록
설계되었습니다. 전원 전압이 명판에 기재된 전압과
일치하는지 항상 확인하십시오.
경고! 충전기를 절대로 일반 전원 플러그로 교체하지
마십시오.
제품과 함께 제공된 배터리를 충전할 때는
BLACK+DECKER 충전기만 사용하십시오. 다른
배터리를 사용하면 배터리가 폭발하여 신체 부상을
당하거나 손해를 입을 수 있습니다.
절대로 비충전식 배터리를 충전하려고 하지
마십시오.
전원 코드가 손상된 경우 사고가 발생하지 않도록
제조업체 또는 공인 BLACK+DECKER 서비스
센터에서 교체해야 합니다.
충전기에 물이 닿지 않도록 하십시오.
충전기를 해체하거나 열지 마십시오.
충전기를 시험하지 마십시오.
제품/배터리는 충전 시 환기가 잘되는 장소에
두어야 합니다.
전기 안전
충전기에 붙은 기호
제품을 사용하기 전에 본 사용 설명서 전체
내용을 잘 읽고 숙지해주십시오.
이 청소기는 이중으로 절연되어 있으므로
접지선이 필요 없습니다. 전원이 전동기
라벨에 기재된 전압과 일치하는지 항상
확인하십시오.
충전 거치대는 실내용으로만 사용합니다.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
19
한국어
제품에 부착된 레이블
다음 기호는 날짜 코드와 함께 본 제품에 나타납니다.
제품을 사용하기 전에 본 사용 설명서 전체
내용을 잘 읽고 숙지해주십시오.
충전기 S010Q 23과만 함께 사용할 것
기능
본 청소기에는 다음 기능들 중 일부 또는 모두가
포함되어 있습니다.
1. On/off 전원 스위치
2. 핸들
3. 노즐
4. 히든틈새노즐
5. LED 충전 표시등
6. 먼지통
7. 푸시 인 브러시
8. 플로어 연장 해제 버튼
9. 플로어 연장관
10. 플로어 헤드 해제 버튼
11. 플립 다운 브러시
12. 플로어 헤드
13. 벽 브라켓
14. 충전기
15. 충전 포트
사용법
전원 켜기 및 끄기 (그림 A)
버튼을 눌러서 장치를 켜고 느린 속도, 낮은 전원
모드에서 작동해서 배터리 수명을 아낍니다.
버튼을 다시한번 누르면, 장치가 BOOST 모드로
들어갑니다.
버튼을 또 다시 누르면, 제품이 꺼집니다.
히든틈새노즐 사용 (그림 B,C)
제자리에 들어가 딸깍 소리가 날 때까지 그림 C와
같이 틈새 노즐 (4) 를 연장합니다. 그런 다음 먼지
청소 및 실내 장식 청소를 위해 필요할 경우 푸시
인 브러시 (7) 를 장착할 수 있습니다.
틈새 도구 (4) 를 집어 넣으려면, 정상 위치로
돌아갈 수 있도록 틈새 도구 해제 버튼 (4a) 을
누릅니다 (그림 B).
플로어 연장관 장착 (그림 D)
그림 D와 같이 ‘딸깍’하는 소리가 들릴 때까지
노즐 (3) 을 플로어 연장관 (9) 으로 밀어 넣습니다.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23 Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
플로어 연장관은 접근하기 어려운 곳을 청소할 수
있도록 플립 다운 브러시 (11) 와 함께 제공됩니다.
플로어 헤드 장착 (그림 F)
그림 F와 같이‘딸깍’하는 소리가 들릴 때까지
플로어 연장관 (9) 을 플로어 연장 헤드 (12) 로
밀어 넣습니다.
바닥 감지 기능
이 제품에는 고유한 바닥 감지 기능이 장착되어
있습니다.
두꺼운 털 카펫을 감지하고 더 우수한 클리닝 성능을
위해 자동으로 저속에서 BOOST 모드로 전환됩니다.
비터 바에서 머리카락 제거 및 청소
(그림 G, H)
그림 G와 같이 비터 바 장치 (16) 해제 버튼 (17)
을 누릅니다.
이제 비터 바 (18) 를 분리할 수 있습니다. 또한
사용 중 쌓일 수 있는 머리카락 또는 기타
먼지덩어리를 말끔히 정리할 수 있도록 선단
부품을 떼어낼 수 있습니다.
충전 (그림 I)
제품은 단일 장치로 또는 플로어 연장관이 장착되어
채로 동안 충전할 수 있습니다.
벽 장착
벽 장착 기능 (13) 은 제품을 편리하게 보관할 수
있도록 벽에 장착할 수 있도록 합니다.
경고! 벽면에 고정하는 경우 벽의 재질에 맞는
고정 방법을 이용하고 제품 무게를 견딜 수 있는지
확인하십시오.
나사 구멍의 위치를 표시합니다 (벽 브라켓에 있을
때는 진공 청소기 충전을 위해 전기 콘센트 도달
범위 내에).
충전기 (14) 를 충전 포트 (15) 에 놓고 전기
콘센트의 플러그를 꽂습니다.
전기 콘센트의 스위치를 켭니다. LED 충전 표시등
(B) 이 점등됩니다.
20
한국어
A. 필터 센서
필터가 막혀서 청소가 필요할 때마다, 핸들에 있는
적색 필터 LED (A) 가 켜집니다.
필터에서 미세 먼지를 닦아냅니다 (이 설명서의“필터
청소”섹션을 참조하십시오).
B. LED 충전 디스플레이
제품에 충전이 필요하면 배터리 아이콘이 점등됩니다.
LED 디스플레이는 충전 상태를 나타냅니다 (본
설명서에서 LED 패턴 차트 참조).
C. BOOST 모드
제품이 더 높은 전력에서 작동할 수 있는 BOOST
모드에 있을 때 켜집니다.
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
멀티 LED 디스플레이
To retract the crevice tool (4) press the crevice tool release
button (4a) allowing it to return to its normal position
(Fig. B).
head (12) until you hear an audible ‘click’ as shown in
Floor sense feature
It senses thick pile carpet and automatically goes from low
speed to BOOST mode for greater cleaning performance.
Removing and clearing hair from the beater
bars
(Fig. G, H)
Depress the beater bar unit (16) release button (17) as
The beater bar (18) can now be removed. The end pieces
are also removable allowing you to clear any hair or other
debris that may have accumulated during use (Fig. H).
Charging (Fig. I)
The appliance can be charged either as a single unit or while
Wall Mounting
The wall mount (13) can be attached to a wall to provide a
convenient storage for the appliance.
Warning!
method is suitable for the wall type and is appropriate to the
weight of the appliance.
Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
Place the charger (14) into the charging port (15) and plug
into the electrical outlet.
Switch the electrical outlet on. The LED charging indicator
(B) will Illuminate.
A. Filter sensor
in this manual).
B. LED Charging display
Battery icon will illuminate when appliance requires
charging. LED display indicates state of charge (See LED
pattern chart in this manual).
C. BOOST mode
Illuminates when the appliance is in BOOST mode
allowing you to operate at higher power.
A
B
C
배터리 과열
LED 패턴
배터리 결함
충전기 결함
충전 중
필터 청소 (그림 J, K, L, M, N)
먼지통 탈착 버튼 (19) 을 누릅니다 (그림 J).
먼지통 (6) 을 제거합니다 (그림 K).
먼지통 (6) 에서 금속 핸들을 사용해 필터 어셈블리
(20) 를 들어 올립니다 (그림 L).
쓰레기통 위를 살짝 흔들어서 먼지통을 비웁니다.
이제 필터 (21) 는 프리필터 (20) 에서 제거할 수
있습니다 (그림 M).
먼지통에서 남은 먼지를 비웁니다.
따뜻한 비눗물로 먼지통을 헹굽니다.
필터를 따뜻한 비눗물로 세척합니다 (그림 N).
필터가 건조되었는지 확인하십시오.
필터를 제품에 다시 장착합니다.
먼지통을 닫습니다. 잠금버튼 (19) 이 제 자리에
딸깍하고 들어가야 합니다.
경고! 제품의 유지 보수 또는 청소를 수행하기 전에
제품의 플러그를 뽑으십시오.
가끔씩 제품을 젖은 헝겊으로 닦아 주십시오.
연마재 및 유성 클리너를 사용하지 마십시오. 본
제품을 물에 담그지 마십시오.
유지 보수
BLACK+DECKER 무선 제품은 최소한의 유지 보수로
장기간에 걸쳐 작업이 가능하도록 설계되어 있습니다.
만족스러운 연속 작동은 적절한 청소기 관리와
정기적인 청소에 따라 그 성능이 달라질 수 있습니다.
경고! 무선 제품에 유지보수를 수행하기 전에:
휴대용 진공 청소기가 내장되어 있는 경우
배터리를 완전히 멈춘 다음 전원을 끕니다.
충전기를 청소하기 전에 충전기의 플러그를
뽑으십시오. 충전기는 정기적인 청소 이외에 유지
보수가 필요하지 않습니다.
부드러운 브러시와 마른 헝겊으로 제품/충전기의
환기 슬롯을 주기적으로 청소하십시오.
젖은 헝겊으로 모터 하우징을 주기적으로
청소하십시오. 연마재 및 유성 클리너를 사용하지
마십시오.
필터 교체
필터는 매 6 ~ 9개월에 한 번 또는 닳거나 손상될
때마다 교체해야 합니다. 교체 필터는 BLACK+DECKER
판매점에서 구입할 수 있습니다.
필터는 제거해야 하는 포일 포장지에 제공됩니다.
필터를 조립하려면, 그림 M을 참조하십시오.
사용하던 필터를 위의 설명에 따라 분리합니다.
새 필터를 위의 설명에 따라 장착합니다.
환경 보호
분리 수거. 이 기호가 표시된 제품과 배터리를
일반 가정용 쓰레기와 함께 처리하면
안됩니다.
Press the dust bowl release button (19) (Fig. J)
Eject the dust bowl (6) (Fig.K)
the dust bowl (6) (Fig.L).
Empty the dust bowl by lightly shaking over a dustbin.
Note: On unit FEJ520JFS the pre filter is impregnated with a
fragrance allowing for a pleasing odour to be released when
the appliance is in use.
(Fig. M).
Empty any remaining dust from the dust bowl.
Rinse out the dust-bowl with warm soapy water.
Close the dust-bowl. Make sure the release latch (19)
clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
-
your BLACK+DECKER dealer (cat. noVPF20)
reach the end of their lifespan they must be disposed of at a
local recycling centre.
Filters are supplied in foil packaging which needs to be
Warning!
Cotton linen fragrance.
Wash face, hands and any exposed skin
thoroughly after handling. Wear protective
gloves/protective clothing/eye protection/
face protection. If in eyes: Rinse cautiously
with water for several minutes. Remove
contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get
medical advice/attention. Avoid release into
the environment. Do not ingest.
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CS1820
Voltage 18V
Weight 2.5Kg
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
to you.
NOTE
Black & Decker's policy is one of continuous improvement to
our products and, as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all countries.
Contact your local Black & Decker dealers for range
availability.
Table of contents
Other BLACK DECKER Vacuum Cleaner manuals
BLACK DECKER
BLACK DECKER BV2000 User manual
BLACK DECKER
BLACK DECKER WDBD10 User manual
BLACK DECKER
BLACK DECKER NVB215WN User manual
BLACK DECKER
BLACK DECKER SVJ520BFS User manual
BLACK DECKER
BLACK DECKER BHFE520J User manual
BLACK DECKER
BLACK DECKER BSV2020G User manual
BLACK DECKER
BLACK DECKER DUSTBUSTER DB1440SV User manual
BLACK DECKER
BLACK DECKER VM2040 User manual
BLACK DECKER
BLACK DECKER BDCV610-LA User manual
BLACK DECKER
BLACK DECKER RVA425B User manual
BLACK DECKER
BLACK DECKER POWERSERIES PRO HCUA525J User manual
BLACK DECKER
BLACK DECKER PV1200AV User manual
BLACK DECKER
BLACK DECKER HHVJ315JDP27 User manual
BLACK DECKER
BLACK DECKER TBSV2020S User manual
BLACK DECKER
BLACK DECKER HNV115B Series User manual
BLACK DECKER
BLACK DECKER Dustbuster SVJ520BFSP User manual
BLACK DECKER
BLACK DECKER NVB12AV User manual
BLACK DECKER
BLACK DECKER WV1450 User manual
BLACK DECKER
BLACK DECKER Dustbuster DVA320BF User manual
BLACK DECKER
BLACK DECKER CYCLONIC POWER PRO User manual
