BLACKHAWK! LAN560 User manual

14
This equipment is designed to be
operated under the following envi-
ronmental conditions:
Temperature between 0°C –55°C.
Relative Humidity of 20% - 70%
non-condensing.
Operation of the unit outside of the
above range may affect structual
and mechanical integrity and
cause permanent damage.
Caution is necessasry to minimize
ESD (Electro-stactic Discharge)
which can damage electronic
components. Use in a controlled
environment where ESD materials
and practices are employed is
highly recommended.
IMPORTANT
ENVIRONMENTAL
CONSIDERATIONS
Important Caveat
 USB DEBUG INSTALL 
This USB debug installation portion of the LAN560 Quick Start Guide series is
intended to show how to configure the LAN560 Emulator for operation with Code
Composer Studio using its LAN port.
For network administration or CCStudio debugging via the LAN interface, please refer
to those specific Quick Start Guides also included with the LAN560 JTAG Emulator.
Inventory of Items Included
1. Blackhawk LAN560 JTAG Emulator POD
(LAN560) and 12 inch JTAG cable.
2. High-Speed USB 2.0 Compliant Cable
3. Ethernet RJ45 Patch Cable
4. 5 Volt DC power supply
5. AC power cord (s)
6. 20-pin cTI JTAG cable.
7. 20e_cTI-14t_TI Pin Converter
8. 20e_cTI-20t_ARM Pin Converter
9. Installation CD
10. Warranty and Product Registration Cards.
11. Quick Start Guide.
Other Items Required
1. Target Board System—a self-powered
board with a TI DSP and compatible JTAG
header connection conforming to IEEE
1149.1 Standard.
2. Copy of Code Composer Studio Version
2.2 †or later.
Installation Requirements
• PC or Notebook computer with one free USB v1.1 or v2.0 port for USB debug or LAN560
administration and/or free Ethernet port for LAN debug†.
• Windows® 2000 or XP/Vista Operating System
• Texas Instruments Code Composer Studio Version 2.2 or later.
• CD-ROM Drive.
†Ethernet connections to a local area network from the LAN560’s Ethernet port is made using a standard RJ45
patch cable (supplied). For direct connection (PC to LAN560) an RJ45 cross-over cable is required (not supplied).
LAN560 administration of TCP/IP address and subnet mask is done via USB port on the emulator.
When using the LAN560 JTAG Emulator via its USB port to debug target hard-
ware with Code Composer Studio, it will use the same settings as the USB560m
JTAG Emulator. The LAN560 is designed to setup and operate the same as the
USB560m when using the USB port to debug.
B.) Using Create Board for CCStudio v3.1 and later
1. Run CCStudio Setup.
2. Select the “Create Board” tab and drag the “BH USB560-M Connection” to My-
System on the left. This will prompt you for a connection name. You can enter
any string you want, but at a minimum, it typically includes the emulator name
and target DSP or board name.
3. Now, highlight the new connection name you added under MySystem and add
the available processor(s) from the middle window to match your h/w.
4. Save you setup and start CCStudio.
A.) Importing a Pre-Defined Import or Factory Board
These instructions apply to CCStudio v2.2 - v3.1, but the import dialog varies slightly between ver-
sions. Refer to the LAN560 Installation Guide if more information is needed.
1. Run CCStudio Setup and for CCStudio v3.0 and earlier, start the Import a Con-
figuration dialog.
2. Find and select “bh-usb560(m)” from the “platform” pull down menu located at
the top of the middle CCSetup window or in the center of the import dialog box
(this will list on only the USB560m imports).
3. You can narrow down the import options further by using the “device” pull down
(i.e. select “C55x“ to list all TMS320C55x device imports).
4. When you find your target, or an import that closely matches your target, high-
light the entry and choose the option to “add it to your system”.
5. If this import setup does not completely match your target, you can edit the
properties manually to add or change a GEL file, modify the TCK rate, or add/
remove/order CPU and Bypass definitions.
6. When finished, save the setup and start CCStudio.
C.) Changing an XDS560 PCI import for CCStudio v2.2-v3.0
1. Run CCStudio Setup and import a setup for the TI XDS560 PCI card that
matches your target (refer to section (A.) above for importing).
2. Highlight the board you added under MySystem, right click with the mouse and
choose properties.
3. Locate the Emulator Name field under board properties tab and change the
name from “XDS560 0” to “BH560USBM 0”. If you need to change other prop-
erties (GEL, DSP, etc.) , you can do that too.
4. Save CCSetup and start CCStudio.
Blackhawk
123 Gaither Drive, Mt. Laurel, NJ 08054-1701
www.blackhawk-dsp.com
Blackhawk is a registered trademark of EWA Technologies, Inc.
LAN560-QSu-04
4Quick Diagnostic
QUICK
START
GUIDE
Blackhawk™
LAN560
JTAG
Emulator (LAN560)
This equipment is designed to be
operated under the following envi-
ronmental conditions:
Temperature between 0°C –55°C.
Relative Humidity of 20% - 70%
non-condensing.
Operation of the unit outside of the
above range may affect structual
and mechanical integrity and
cause permanent damage.
Caution is necessasry to minimize
ESD (Electro-stactic Discharge)
which can damage electronic
components. Use in a controlled
environment where ESD materials
and practices are employed is
highly recommended.
IMPORTANT
ENVIRONMENTAL
CONSIDERATIONS

2 3
USB PnP Installation 3
The LAN560 JTAG Emulator shipped with its drivers on CDROM media that are
needed by Windows and Code Composer Studio for operation.
WARNING
Be careful to connect interface cables with the correct orientation. Pin 1 on the inter-
face cable should match Pin 1 on the DSP system connector. The JTAG cable as-
sembly features a "keyed" connector to minimize the chance of error.
Make sure the target is not powered when connecting!
2Hardware Installation
1Emulation Driver Installation
Important Caveat
When using the LAN560 JTAG Emulator via its USB port to debug target hard-
ware with Code Composer Studio, it will use the same settings as the USB560m
JTAG Emulator. The LAN560 is designed to setup and operate the same as the
USB560m when using the USB port to debug.
1. Insert the Emulation Driver CD.
2. Follow the installation wizard, and when done, you are ready to install the emula-
tor hardware.
1. Place the LAN560 module in desired location.
2. Connect the 5v DC power plug of the power supply to the 5-volt DC input on the
LAN560 (see figure 1).
3. Attach the USB cable to an available USB port on the PC and to the USB connec-
tor on the LAN560 (see figure 1).
4. If not already connected, attach the JTAG cable assembly to the corresponding
“D” connector of the LAN560 (see figure 2).
5. Connect the power supply A/C wall cord to A/C power, which will power the
LAN560 and initiate Plug and Play installation for the Windows device driver (see
step 3 on USB PnP Installation).
6. Follow the Windows Plug and Play Found New Hardware Wizard Installation for
the Windows Device Driver (see step 3 on USB PnP Installation).
NOTE
If the installation executable fails to start automatically,
run X:\Setup\Setup.exe,
where [X] is the drive letter for your CDROM drive.
FIGURE 1—LAN, USB & Power Endplate
FIGURE 2—JTAG End Plate
5V DC Input
High-speed USB
Cable Connection
Separate Status
and Activity LED’s
Windows 2000/XP/Vista
1. Make sure the LAN560 Emulator is powered.
2. Connect the USB cable to the emulator and to the computer.
3. Follow the Windows “New Hardware” prompts selecting the location
where the Blackhawk USB device drivers exist. These file were in-
stalled to your system during the Emulation Driver Installation—
section 1. Typical location for these files is folder:
C:\CCStudio_v3.3\blackhawk\drivers.1\LAN.
4. When completed, the Blackhawk Control Panel and Windows Device
Manager will show the device. The Blackhawk Control Panel can be
activated from its icon, located in the Windows Control Panel Dialog
Box.
5. Now follow the Code Composer Studio Setup—Section 4
RJ45 Ethernet
Port
JTAG Cable
Connection
“D” Connector