Blake UK SS/BKT08 User manual

PD2011-8020-0D
Installation guide
SS/BKT08
SS/BKT08
Safety
Working at height  carry out work outdoors at height only if you are competent in the use of ladders and related access equipment.
Always work safely within your own limitations, ensuring that all equipment used is appropriate and is in good condition.
Fit a suitable aerial mast to the bracket using V bolts. It may be
necessary to use a cranked mast i the chimney has a stepped
top (avoid positioning the aerial over the top o an operating
chimney as heat and gas may a ect per ormance over time).
Maximum recommended length o aerial -1 metre; maximum
recommended mast length - 5 t (1.5 metre). For heavier
installations use multiple products.
Do not install this product on a chimney which is in poor condition
(loose or damaged, cracked or heavily weathered bricks). For
stability do not use the top three courses o chimney brickwork.
1. Fold back one end of strap as shown and pinch flat
with pliers.
2. Pass strap around chimney and cut to size allowing a
10cm ( ) overlap on each end (this will be taken up
when operating ratchet). To assist passing the strap
around a larger chimney, pre-feed strap into a short
section of 1.25 mast then using a fishing rod action,
encircle chimney. Pull off masting to leave strap in
position.
3. Feed folded end of strap through centre of ratchet
spindle as shown. Pull strap back so that folded
end acts as a hook.
4. Feed other end of strap through opposite side of ratchet
spindle and fold back around ratchet spindle as shown.
Operate ratchet lever to tighten strap securely. Ensure
the strap stays horizontal around chimney while
operating ratchet. For final tightening, position ratchet
handle in open position as shown and push with the
palm of the hand rather than pulling from the closed
position. Fold lever flat when finished. If the strap needs
to be loosened for re-positioning, the ratchet may be
released by pulling back the spring loaded release lever
in the handle.
Accessories for use with this bracket (not included):
SS/STRAP/5M - 5m Individual Strapping Coil
SS/DISP100 - 100m Roll Strapping Dispenser Pack
AC2 1.75 V Bolts.
25 mm (1)
Further advice may be downloaded rom:
www.blake-uk.com/downloads on the ollowing:
nreception problems
nitting coaxial connectors
ndistributing TV signals around the home
ngeneral recommendations
keep this
length short
release lever

3. Feed folded end of strap through centre of first ratchet spindle as shown. Pull strap back so that folded end acts as
a hook. Feed other end of strap through centre of second ratchet spindle and fold back through lever as shown.
Operate this ratchet to tighten. Remove any slack on the strap with the first ratchet. Tighten strap by operating both
ratchets alternately ensuring that strap stays horizontal around chimney. For final tightening, position ratchet handle
in open position as shown and push with the palm of the hand rather than pulling from the closed position. Fold levers
flat when finished. If the strap needs to be loosened for re-positioning, the ratchets may be released by pulling back
the spring loaded release levers in the handles.
SS/BKT14
Installation guide
SS/BKT14
Further advice may be downloaded rom:
www.blake-uk.com/downloads on the ollowing:
nreception problems
nitting coaxial connectors
ndistributing TV signals around the home
ngeneral recommendations
Safety
Working at height  carry out work outdoors at height only if you are competent in the use of ladders and related access equipment.
Always work safely within your own limitations, ensuring that all equipment used is appropriate and is in good condition.
1. Fold back one end of strap as shown and pinch flat
with pliers.
2. Pass strap around chimney and cut to size allowing a
10cm ( ) overlap on each end (this will be taken up when
operating ratchets). To assist passing the strap around a
larger chimney, pre-feed strap into a short section of 1.25
mast then using a fishing rod action, encircle chimney.
Pull off masting to leave strap in position.
25 mm (1)
Accessories for use with this bracket (not included):
SS/STRAP/5M - 5m Individual Strapping Coil
SS/DISP100 - 100m Roll Strapping Dispenser Pack
AC2 1.75 V Bolts & AC4 2.5 V Bolts.
Fit a suitable aerial mast to the bracket using V bolts. It may be
necessary to use a cranked mast i the chimney has a stepped top
(avoid positioning the aerial over the top o an operating chimney as
heat and gas may a ect per ormance over time).
Maximum recommended length o aerial - 2 metres; maximum
recommended mast length - 10 t (3 metres). For heavier installations
use multiple products.
Do not install this product on a chimney which is in poor condition
(loose or damaged, cracked or heavily weathered bricks). For
stability, do not use the top three courses o chimney brickwork.
keep this
length short
release lever