Blankom LANIOS 5160.01 User manual

Professional Headend Solutions
Operating instructions
LANIOS
Part No: 5160.01
8-port switch

2
LANIOS
Part No: 5160.01 8-port switch
SBL
Contents
1. Safety and operating instructions .............................................................................................................3
2. Device variants .......................................................................................................................................3
3. General ................................................................................................................................................... 3
4. Front view ...............................................................................................................................................3
5. Functional description ............................................................................................................................4
6. Meaning of the LED`s at the 10/ 100 Mbit ports .................................................................................... 4
7. Technical data ..................................................................... ...................................................................4
8. Bibliography ..................................................................................... ...................................................... 4
9. Document history ...................................................................................................................................4

3
LANIOS
Part No: 5160.01 8-port switch
SBL
1. Safety and operating instructions
When assembling, starting-up and adjusting the modules, it is necessary to consider the system specific references in
the manual instruction
The modules may only be installed and started up by authorized technical personnel. There are only permitted the
mounting styles indicated in the quick start guide, which is included each module.
When assembling the modules into the receiving points, the adherence of the EMC regulations is to be ensured.
The assembly and wiring have to be done without voltage. For installation, only the supplied accessories (DIN rail clip
with screws and 19“ accessories) may only be used.
All active modules may only be operated with the power supply HELIOS. To supply the module only the attached accessory
cables are used.
The mains voltage and the operating voltage of the modules working by DC have to be in complience to the operating
parameters described in the technical data.
With all work the defaults of the DIN EN 50083 have to be considered! Especially the safety relevant execution of the
DIN EN 60728-11[1] is necessary.
The unit should be mounted only vertically. The ventilation slots as well as the circulation perforation of the modules must
be kept absolutely free.
If installed in mounting cabinets a adequate heat circulation must be guaranteed. The mounting in closed cabinets with
no air exchange is not allowed.
For DIN rail mounting is important to note that between the heat sink and a neighboring building, a distance of 2 cm is
required. If the modules mounted on top of each, so to observe a distance of 20 cm from the bottom edge of the top
module to top edge of the lower module
For 19“ mounting all devices in the rack must be fitted with 19“ Edge Guide. The sole panel mounting is not enough!
Furthermore, the operation of a fully occupied rack is only allowed with an underlying 1-U fan box (at least 3 fans,
176 mm deep).
2. Device variants
LANIOS 5160.01 8-port switch
3. General
The Smart Business Line (SBL) is a modern head end system, that is distinguished by its modular and compact design. A userfriendly
operating concept facilitates setup, configuration and maintenance of the system.
The module LANIOS is the 8-port Ethernet switch created for the SBL system.
4. Front view
LANIOS
12 VDC
I
II
III
IV
V
VI
VII
VIII
Port 1 ... 4
Power connectors (loop through)
LED “POWER“ (green)
Port 5 ... 8

4
LANIOS
Part No: 5160.01 8-port switch
SBL
5. Functional description
The LANIOS module is a 8-port 10/ 100 Base-T Ethernet switch, which was created for the SBL system. It fits seamlessly into the SBL
case, control and quality concept. With the switch up to 7 SBL modules can be controlled via a PC/ laptop. If more ports are needed,
cascading is possible.
Auto negotiation and auto MDI/ MDIX crossover are integrated, IGMP snooping is supported.
6. Meaning of the LED‘s at the 10/ 100 Mbit ports
Designation/ colour Status Meaning of display
Connect-LED/ yellow permanently on network cable is connected
off no cable connection
Data-LED/ green flashing data exchange
off no data exchange
7. Technical data
Network ports
Link attributes 8x Ethernet, 10/ 100 Base-T
according IEEE 802.3,
IEEE 802.3u, IEEE 802.3x
Connectors 8x RJ 45
Operating parameters
Voltage range 5 ... 15 V DC
Max. current consumption 150 mA at 12 V DC
Power consumption about 1.5 W
Environmental conditions
Temperature range -10 … +55 °C
Relative humidity ≤ 80 % (non condensing)
Method of mounting vertical
Location of mounting splash-proof and drip-proof
Miscellaneous
Dimensions (l x w x h) 46 x 262 x 167 mm
Weight 850 g
Delivery contents 1x power cord
1x DIN rail clip
1x mounting accessories
BLANKOM Antennentechnik GmbH
Hermann-Petersilge-Straße 1 • 07422 Bad Blankenburg • Germany • Telefon [phone] / 60-0 • Fax [phone] / 60-100
Options available upon request! Subjects to changes due to technical progress.
8. Bibliography
[1] EN 60728-11: Cable networks for television signals, sound signals and interactive services Part 11: Safety
(IEC 60728-11:2005); German version EN 60728-11:2005
[2] EN 50083-2 : Cabled distribution systems for television and sound signals. Electromagnetic compatibility for equipment;
EN 50083-2:2001
9. Document History
Version Date Modification Author
1.00 14.07.2011 basic document Häußer

5
Declaration of Conformity
The Manufacturer
BLANKOM Antennentechnik GmbH ∙ Hermann-Petersilge-Str. 1 ∙ 07422 Bad Blankenburg ∙ Germany
herewith declares the conformity of the product
Product name: 8-port switch
Type: LANIOS
Product number: 5160.01
according to the following regulations
EN 50083-2
EN 60728-11 (as far as relevant)
and additional device-specific regulations, enclosed above, which this product is subjected to.
Date: 14.07.2011
Signature:
Piero Kirchner
(Managing Director)