Blaze King CLARITY CL26.IPI.1A User manual

180-CL26.IPI.1A v2.00 May 27, 2022
CLARITY CL26.IPI.1A
FREESTANDING DIRECT VENT GAS ROOM HEATER
with Intermittent Pilot Ignition (IPI)
For use with Natural Gas (NG) or Propane (LPG)
Installer: Please COMPLETE THE DETAILS ON THE LAST PAGE
and leave this manual with the homeowner.
Homeowner: Please SAVE THESE INSTRUCTIONS for future reference.
PFS REPORT: #F19-558
OPERATION & INSTALLATION MANUAL
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com
ATTENTION: The authority having jurisdiction (municipal building department, re department, etc.) should be
consulted before installation to determine the need to obtain a permit.
MANUFACTURED BY
Valley Comfort Systems Inc., 1290 Commercial Way, Penticton BC, Canada, V2A 3H5
web: www.blazeking.com email: [email protected]
Blaze King recommends that its gas hearth products be installed
and serviced by professionals who are certied in the U.S. by the
National Fireplace Institute (NFI) as NFI Gas Specialists.

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings
exactly could result in serious injury,
death, or property damage.
— Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Leave the premises.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the re department.
— Installation and service must be
performed by a qualied installer, service
agency or the gas supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certied
kit is used.
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals. If the barrier becomes
damaged, the barrier shall be replaced with the
manufacturer’s barrier for this appliance.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 3
CL26.IPI.1A PREFACE
The content within this manual describes the installation
and operation of the Blaze King Clarity CL26.1A. It is
against federal regulations to operate this appliance in a
manner inconsistent with the operating instructions in this
manual. Blaze King grants no warranty, implied or stated,
for the installation and maintenance of this appliance
and assumes no responsibility of any consequential
damage(s).
This appliance is tested and certied to the following US and Canadian gas appliance standards:
• ANSI Z21.88-2017 / CSA 2.33-2017 - Vented Gas Fireplace Heaters
• CSA 2.17-2017 - Gas-Fired Appliance for Use at High Altitudes
• CSA P.4.1-15 - Testing Method for Measuring Annual Fireplace E󰀩ciency
This appliance must be installed by a qualied gas installer. The installation must conform to local codes or,
in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the US, or the
Natural Gas and Propane Installation Code, CSA B149.1 in Canada. This appliance is certied for installation
in a bedroom or a bedsitting room and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. This appliance is certied for direct vent discharge only.
This appliance must be vented using the listed and approved vent components described in this manual.
TEST CERTIFICATION DATA
Natural Gas
(NG)
Propane
(LPG)
Steady State E󰀩ciency
(High / E󰀨ySS,H)
67.29% 65.75%
Fireplace E󰀩ciency
(P4 / FE)
65.00% 61.00%
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to chemicals including
benzene, which is known to the State of California to cause cancer and
birth defects or other reproductive harm. For more information:
www.P65Warnings.ca.gov
IF THIS APPLIANCE IS NOT PROPERLY INSTALLED OR OPERATED, A HOUSE FIRE MAY
RESULT LEADING TO SERIOUS BODILY HARM AND EVEN DEATH. TO REDUCE THE RISK OF FIRE, PLEASE
READ THIS ENTIRE MANUAL BEFORE INSTALLING AND OPERATING THIS APPLIANCE. CONTACT LOCAL
BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN
YOUR AREA.
DO NOT OPERATE THIS APPLIANCE WITHOUT FULLY ASSEMBLING ALL COMPONENTS. DO NOT INSTALL
DAMAGED, INCOMPLETE, OR SUBSTITUTE COMPONENTS. FAILURE TO POSITION COMPONENTS IN
ACCORDANCE WITH THE DIAGRAMS IN THIS BOOKLET OR FAILURE TO USE COMPONENTS SPECIFICALLY
APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 4 CL26.IPI.1A
TABLE OF CONTENTS
SPECIFICATIONS ___________________________________________________________________ 5
APPLIANCE DIMENSIONS ___________________________________________________________ 6
SAFETY CLEARANCES_______________________________________________________________ 7
SAFETY PRECAUTIONS______________________________________________________________ 8
VENTING __________________________________________________________________________ 9
OPTIMAL VENTING PERFORMANCE............................................................................................... 9
VENT CONNECTIONS .......................................................................................................................... 9
VENT TERMINATION LOCATION...................................................................................................... 9
VENT TERMINATION RESTRICTIONS.............................................................................................. 10
VENTING CONFIGURATIONS ............................................................................................................ 11
VENT LENGTH CALCULATION ......................................................................................................... 11
VERTICAL VENT INSTALLATION...................................................................................................... 12
CEILING PASS THROUGH.................................................................................................................... 12
THROUGH ROOF FRAMING............................................................................................................... 12
ABOVE ROOF TERMINATION............................................................................................................. 13
EXTERIOR WALL PASS THROUGH .................................................................................................... 13
INSTALLATION _____________________________________________________________________ 14
GAS CONNECTIONS ............................................................................................................................. 14
ELECTRICAL REQUIREMENTS........................................................................................................... 14
BATTERY HOLDER ................................................................................................................................ 14
HIGH ALTITUDE INSTALLATION...................................................................................................... 14
INITIAL SETUP ...................................................................................................................................... 15
MOBILE HOME INSTALLATION ........................................................................................................ 17
VENT RESTRICTOR .............................................................................................................................. 17
AIR SHUTTER ADJUSTMENT ............................................................................................................ 18
PROFLAME 2 WIRING DIAGRAM ..................................................................................................... 19
PROFLAME VALVE SCHEMATIC ....................................................................................................... 20
FUEL CONVERSION ............................................................................................................................. 21
LIGHTING INSTRUCTIONS___________________________________________________________ 24
REMOTE OPERATION _______________________________________________________________ 25
MAINTENANCE and SERVICE ________________________________________________________ 30
ROUTINE MAINTENANCE .................................................................................................................. 30
CLEANING SURFACES.......................................................................................................................... 30
CLEANING DOOR GLASS..................................................................................................................... 30
DOOR GLASS REPLACEMENT ............................................................................................................ 30
SAFETY SCREEN REPLACEMENT ...................................................................................................... 30
VENTING COMPONENTS ____________________________________________________________ 31
PARTS LIST ________________________________________________________________________ 38
TROUBLE SHOOTING _______________________________________________________________ 39
WARRANTY________________________________________________________________________ 42
NOTES ____________________________________________________________________________ 46

180-CL26.IPI.1A v2.00 May 27, 2022
Page 5
CL26.IPI.1A SPECIFICATIONS
CLARITY 26 IPI, CL26.IPI.1A SPECIFICATIONS
Flue Vent Size 4” x 6 5/8”
Electrical Rating 120 V.A.C.
Shipping Weight 200 lbs (90.7 kg)
Natural Gas (NG) Propane (LPG)
Manifold Pressure 3.8” w.c. (0.95 kPa) 10.6” w.c. (2.64 kPa)
Minimum Supply Pressure for
Purpose of Input Adjustment 7.0” w.c. (1.74 kPa) 11.0” w.c. (2.74 kPa)
Orice Size DMS #39 DMS #1.5 mm
Nominal Input Rating 27,300 BTU/hr 26,200 BTU/hr
Minimum Input Rating 14,838 BTU/hr 14,120 BTU/hr
Primary Air Opening 50% (Minimum) Open
PARTS INCLUDED
1. Manual Kit (w/ Manual, Warranty Cards, Remote, and Batteries)
2. Floor and Side Glass Panels
3. Rear Ceramic Panel
OPTIONAL ACCESSORIES
1. S.Z5177.IPI - Fan Kit 2. S.Z0519 - 5 Piece Log Set
3. S.ZPFC - Connected Smart Home Kit 4. S.Z0765 - LPG Conversion Kit
5. S.Z0766 - NG Conversion Kit

180-CL26.IPI.1A v2.00 May 27, 2022
Page 6 CL26.IPI.1A
APPLIANCE DIMENSIONS
383
8
"
976mm
371
2
"
952mm
131
2
"
343mm
377
8
"
962mm
143
4
"
373mm
VERTICAL
VENT
161
2
"
419mm
237
8
"
607mm
181
8
"
461mm
1
3
4
"
45mm
NOTE: RATING AND LIGHTING INSTRUCTION LABELS
ARE LOCATED ON THE RIGHT AND LEFT SIDE PANELS.
LIFT THE LOWER SIDE PANELS UP AND OFF TO VIEW.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 7
CL26.IPI.1A SAFETY CLEARANCES
A
F
E
D
A
B
108
4 1/4"
353
13 7/8"
G
C
C
245
9 5/8"
722
283
8
"
MINIMUM CLEARANCE TO COMBUSTIBLES
AAppliance to Side Wall 2” (51 mm)
BAppliance to Rear Wall 2.5” (64 mm)
CAppliance Corner to Side/Rear Wall 2” (51 mm)
DAppliance Top to Alcove Ceiling 33” (838 mm)
EAlcove Width 27.875” (708 mm)
FAlcove Height 70.5” (1791 mm)
GAppliance Vent to Side/Rear Wall 1” (25 mm) from outer surface
NOTE: CHECK LOCAL CODES FOR FLOOR PROTECTION REQUIREMENTS.
THIS APPLIANCE IS CERTIFIED FOR INSTALLATION ON A COMBUSTIBLE SURFACE.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 8 CL26.IPI.1A
SAFETY PRECAUTIONS
YOUR SAFETY
• To prevent injury, do not allow anyone who is unfamiliar with the appliance to operate it.
• The appliance should be inspected before initial use and, at least, annually by a qualied service person.
• It is imperative the control compartments, burners, and circulating airways of the appliance be kept clean.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
• Always connect this gas appliance to a vent system and vent to the outside of the building envelope. Do
not vent to another room or inside the building. Do not connect to a chimney ue serving a separate solid-
fuel burning appliance. Ensure the specied vent pipe is used, properly sized, and of adequate height to
provide su󰀩cient draft. The ow of combustion and ventilation air must not be obstructed.
• Have the venting system inspected annually by a qualied installer for blockage and signs of deterioration.
• If this appliance is pulled out of its installation and/or the vent-air intake pipes are disconnected for
any reason, ensure that the vent-air intake pipes are reconnected and re-sealed in accordance to the
instructions noted in the “INSTALLATION” section.
• Due to high temperatures, this appliance should be located out of high tra󰀩c areas and away from furniture
and draperies.
• Young children should be carefully supervised when in the same room as the appliance. Toddlers, young
children, and others may be susceptible to accidental contact burns. A physical barrier is required if
there are at risk individuals in the house. To restrict access to the appliance, install an adjustable safety
gate to keep toddlers, young children, and other at risk individuals out of the room and away from hot
surfaces. Any safety screen, guard, or barrier removed for servicing the appliance must be replaced prior
to operating the appliance.
• Clothing or other ammable materials should not be placed on or near the appliance. This appliance should
not be used as a drying rack for clothing or for hanging Christmas stockings/decorations.
• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this appliance.
• Due to the paint curing, a faint odor and slight smoking will likely be noticed when the appliance is rst
used. Open a window until the smoking stops.
• To prevent injury, if the pilot or pilot and burners have gone out on their own, open the glass door and wait
5 minutes to air out before attempting to relight the appliance.
• Do not use this appliance if any part has been under water. Immediately contact a qualied service
technician to inspect the appliance and to replace any part of the control system and any gas control which
has been under water.
• Do not abuse the glass by striking it or slamming the door shut.
FIRE OR EXPLOSION HAZARD. FAILURE TO FOLLOW SAFETY WARNINGS EXACTLY COULD RESULT IN
PROPERTY DAMAGE, SERIOUS BODILY HARM, OR DEATH.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 9
CL26.IPI.1A VENTING
VENT TERMINATION LOCATION
• In heavy snowfall areas make sure the vent termination is located where it will not be blocked by snowfall
or snow from snow removal equipment.
• Locate the vent termination away from plants, bushes, or any other object on or near the vent termination
that will interfere or obstruct the air ow around it.
• Do not recess vent termination into walls, sidings, or planters.
• Vent terminations located below 7 ft (2130 mm) from grade level or anywhere that it is a burn hazard to the
public, such as patios and balconies, must be protected with an approved termination cage.
A MINIMUM CLEARANCE OF 13” (330 mm) MUST BE MAINTAINED FROM COMBUSTIBLE MATERIAL ABOVE
ANY HORIZONTAL VENT RUN. A MINIMUM CLEARANCE OF 1” (26 mm) MUST BE MAINTAINED AROUND
ALL OTHER VENT RUNS (VERTICAL OR HORIZONTAL).
FAILURE TO COMPLY WILL VOID WARRANTY AND MAY RESULT IN PROPERTY DAMAGE.
ALLOWING HORIZONTAL VENT PIPE TO SLOPE DOWN TOWARDS THE VENT TERMINATION COULD CAUSE
POOR COMBUSTION AND/OR HIGH TEMPERATURES THAT MAY PRESENT A FIRE HAZARD.
MAINTAIN AN UPWARD SLOP OF 1/4” (7 mm) FOR EVERY 1 ft (305 mm) OF HORIZONTAL VENT RUN.
OPTIMAL VENTING PERFORMANCE
For best venting performance, follow these guidelines:
1. This appliance must be vented using the following listed and approved vent components: Selkirk
(Direct-Temp), Americent, M&G Duravent, BDM, Olympia, and ICC. Read the manufacturer’s
installation instructions before installing the venting system.
2. The venting of this appliance must be installed in a location free of plumbing, electrical wiring, and
heating or air conditioning ducts.
3. Observe minimum and maximum vent height and length restrictions stated in this manual.
4. Never slope horizontal vents downwards. Support horizontal vent runs every 3 ft (915 mm) to prevent
sagging.
5. This appliance needs fresh air for safe operation and must be installed with provisions for adequate
ventilation air. Provide clearance around air openings of the appliance. Do not obstruct openings.
6. Provide adequate clearances for servicing of the appliance.
VENT CONNECTIONS
Rigid vent systems use twist lock connections. The female end of the vent pipe has four indentations evenly
spaced around the pipe which are designed to slide over the male end of the vent pipe and locate into four
entry slots. To ensure a completely sealed vent system, a high temperature sealing compound must be used to
seal the joints. Apply a bead of high temperature sealant (NON-SILICONE) to both the 4” exhaust and 6-5/8”
intake section of the vent pipe before connecting. Once connected, fully twist the vent pipe to ensure solid,
locked connections.
Note: When assembling, ensure seams are aligned and hidden to yield best visual appearance.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 10 CL26.IPI.1A
VENTING
12 in (30.5 cm) to 24” (61 cm)
VENT TERMINATION RESTRICTIONS
TABLE 1 - VENT TERMINATION CLEARANCES

180-CL26.IPI.1A v2.00 May 27, 2022
Page 11
CL26.IPI.1A VENTING
VENT LENGTH CALCULATION
Example 1
V Value = 3A (12’) + 1C (3’) = 15’
H Value = 2B (4’) =4’
V Value = Total length of all vertical sections in feet.
H Value = Total length of all horizontal sections in feet.
Note:
• for H & V values for 45º venting, see Chart IV
• elbows are not counted in H or V values
• vent chart starts from the top of the unit
CHART IV
VENTING CONFIGURATIONS
• Maximum total vent length = 36 ft (10.97 m)
• Maximum vertical vent length = 36 ft (10.97 m)
• Minimum vertical vent length = 2 ft (0.61 m)
• Maximum horizontal vent length = 20 ft (6.10 m), with minimum 4 ft (1.22 m)
vertical o󰀨 appliance
• Minimum horizontal vent length = 1 ft (0.30 m), with minimum 2 ft (0.61 m)
vertical o󰀨 appliance
Note:
• No more than 4 - 90° elbows, or equivalent, allowed.
• Must use vent restrictor on vents from 15 ft (4.57 m) to 20 ft (6.09 m) to
obtain optimal ame appearance, see “VENT RESTRICTOR” and “BURNER
FLAME APPEARANCE”.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 12 CL26.IPI.1A
VENTING
VERTICAL VENT INSTALLATION
When planning your installation determine if ceiling joists, roof
rafters, or other framing will obstruct the vent system. You may have
to use 45° elbows to navigate around obstacles. Always maintain
a 1” clearance around the vertical vent pipe when passing through
ceilings, roofs, enclosures, attic rafters, or any combustible surfaces.
Note: Do not pack air spaces with insulation.
• If an o󰀨set is necessary in the attic to avoid obstructions,
it is important to support the vent pipe every 3 ft (914 mm)
to avoid excessive stress and possible seperation on the
elbows. Use wall straps as needed (Fig. 1).
• When possible, use 45° elbows rather than 90° elbows to
reduce restriction to the ow of ue gases and intake air.
• For multi story installations, a ceiling restop is required at the
second oor, and on any subsequent oors (Fig. 2).
• Any occupied areas above the rst oor, including closets
and storage spaces, which the vertical vent passes through
must be enclosed. The enclosure may be framed and sheet-
rocked with standard building materials. However, consult
the appliance manufactures installation instructions for the
minimum allowable clearance between the outside of the vent
pipe and the combustible surfaces of the enclosure. Do not ll
any required air spaces with insulation.
Fig. 1
Fig. 2
THROUGH ROOF FRAMING
Maintain a 10” (254 mm) opening relative to the pitch of the roof. Use a
suitable round or square support through the roof. Ensure adequate heat
shield protection is provided (Fig. 4).
Fig. 3
CEILING PASS THROUGH
When passing through a at ceiling install a Ceiling Box or
Wall thimble. Cut a 10” (254 mm) square hole and frame
(Fig. 3). Ensure all pipe sections are fully twist locked.
Fig. 4

180-CL26.IPI.1A v2.00 May 27, 2022
Page 13
CL26.IPI.1A VENTING
ABOVE ROOF TERMINATION
The vent must be a minimum 2’ (610 mm) from any wall. Install ashing
with the upper portion slid under the roong material and the lower portion
over the roong material (Fig. 5). Consult local codes for minimum vent cap
height above the roof.
Note: Do not fully fasten until nal adjusments have been made.
Fig. 5
EXTERIOR WALL PASS THROUGH
Mark a 10” (254 mm) square around the center mark. Cut and frame the exterior wall to accept the wall
penetration heat shield. Install the shield using wood screws. If the wall being penetrated is constructed of
non-combustible material, a 7” (178 mm) diameter hole is acceptable.
NOTE: When installing a termination onto vinyl siding, a vinyl siding kit must be used. This prevents
the termination from being recessed into the siding. Apply a bead of non-hardening mastic to form a seal
between the stando󰀨 and the termination cap. Attach the termination cap to the exterior wall by inserting four
wood screws through the holes in the corners of the vent termination. Complete the installation by applying a
bead of mastic around the outer edge of the vinyl stando󰀨. With the termination cap installed, you can now
connect the vent pipe by sliding the appliance back towards the wall and carefully inserting the vent pipe into
the terminal. Before the nal connection is made, slide on the decorative wall thimble. Secure the termination
cap by fastening the termination straps to the pipe as close to the exterior wall as possible using sheet metal
screws. Ensure that the straps are hidden by the wall thimble cover. Apply decorative trim if required.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 14 CL26.IPI.1A
INSTALLATION
GAS CONNECTIONS
Have your gas supplier or a qualied gas tter run a gas supply line to the appliance. The line must be properly
sized and tted according to the installation codes. This appliance is equipped with a manual shuto󰀨 ball valve
with a 1/2” female pipe thread outlet. Check for proper gas supply pressure:
• Use a small, at tip screw driver to loosen the set screw on supply pressure tap on the gas valve (refer to
“PROFLAME VALVE SCHEMATIC” for pressure tap location).
• Once loose, place a test gauge on the tap.
• The minimum supply pressure is 7.0” w.c. (1.24 kPa) for natural gas and 11.0” w.c. (3.0 kPa) for propane.
• The maximum supply pressure should never exceed 14.0” w.c. (3.48 kPa) or 0.5 psi for both natural gas
and propane.
• When nished testing, be sure to retighten the pressure tap set screw.
Before connecting the appliance to the gas supply line, double check that the appliance is indeed designed for
the gas type you are using. The gas type markings are located on the appliance rating label as well as on the
appliance’s gas valve. Adequate clearance for proper installation and checking of the gas connections must be
provided. All gas connections must be checked for gas leaks before appliance operation.
NOTE: THIS SECTION OF THE MANUAL IS FOR THE USE OF QUALIFIED SERVICE PERSONS ONLY.
THIS APPLIANCE AND ITS MANUAL SHUTOFF VALVE MUST BE DISCONNECTED FROM THE GAS SUPPLY
PIPING SYSTEM DURING ANY PRESSURE TESTING WHERE TEST PRESSURES EXCEED 1/2 psi (3.5 kPa).
THE APPLIANCE MUST BE ISOLATED FROM THE GAS SUPPLY PIPING SYSTEM BY CLOSING ITS MANUAL
SHUTOFF VALVE DURING ANY PRESSURE TESTING WHERE TEST PRESSURES ARE EQUAL TO OR LESS
THAN 1/2 psi (3.5 kPa).
FAILURE TO COMPLY WILL DAMAGE THE APPLIANCE’S GAS VALVE AND VOID MANUFACTURER’S
WARRANTY.
ELECTRICAL REQUIREMENTS
This appliance must be electrically grounded in accordance with local codes or, in the absence of local codes,
with the National Electrical Code ANSI / NFPA 70 in the U.S. or the Canadian Electrical Code CSA C22.1 in
Canada. This appliance is equipped with a three prong grounding plug for protection against shock hazard
and should be plugged directly into a properly grounded three pronged receptacle. Do not cut or remove the
grounding prong from this plug. Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation. Verify proper operation after servicing.
HIGH ALTITUDE INSTALLATION
When installing this appliance above altitudes of 4500 ft (1372 m) above sea level, the appliance must be
properly de-rated and installed according to local codes or, in the absence of local codes, with the current
National Fuel Gas Code ANSI Z223.1/ NFPA 54 in the U.S. or Installation Code CSA-B149.1 in Canada.
BATTERY HOLDER
There are four AA batteries supplied with the appliance that must be installed into the battery holder located
in the control housing. The life span of the batteries depends on various factors: quality of batteries used,
the number of ignitions of the appliance, the number of changes to the room thermostat set point, etc. It is
recommended that the batteries be checked/replaced once a year.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 15
CL26.IPI.1A INSTALLATION
INITIAL SETUP
1. Remove the Top Lid from appliance and set aside.
(Fig. 8)
2. Locate the two Door Latch Springs on top of the
Firebox. Pull both tabs forward, up, and o󰀨 the
upper door tabs. (Fig. 8)
3. Carefully slide the Door up and out of the appliance
and set aside. (Fig. 9) Note: Press the door
glass to the door frame when removing the
door as the glass is only held in place with
silicone. Remove the warning label a󰀩xed to the
door glass at this time.
4. Slide the Safety Screen up and out of the appliance
and set aside. (Fig. 10)
5. Remove the packaged contents from inside the
Firebox and set aside in a safe place.
Fig. 8
Fig. 9
Fig. 10

180-CL26.IPI.1A v2.00 May 27, 2022
Page 16 CL26.IPI.1A
INSTALLATION
6. Remove the Foor Plate assembly from Firebox and
set aside. (Fig. 11)
7. Inside the Firebox, loosen the fastener securing
the upper left tab (Fig. 12) and then install the
Left Side Glass Panel up under the tab while
resting on the lower support. Note: Handle glass
carfully by the edges. Wear gloves to avoid
leaving ngerprints, clean before installing if
necessary. The label a󰀩xed to the side glass
should be facing into the rebox. Once the glass
is in place, re-tighten the upper tab. Remove the
label from the glass panel at this time.
8. Repeat Step 7 to install the Right Side Glass
Panel.
9. Carefully place the Floor Plate assembly back into
position and then place the Floor Glass Panel on
top. (Fig. 13) Note: The smooth side of the oor
glass panel should face up.
10. If installing an optional Log Set, please refer to the
installation instructions provided with the Log Set
Kit. If not installing a Log Set, repeat Steps 1 to 4
in reverse order to complete the initial setup.
Fig. 12
Fig. 13
Fig. 11

180-CL26.IPI.1A v2.00 May 27, 2022
Page 17
CL26.IPI.1A INSTALLATION
MOBILE HOME INSTALLATION
This appliance is approved for installation in a manufacture (mobile) home. A manufactured home (USA
only) or mobile home OEM installation must conform with the Manufactured Home Construction and Safety
Standard Title 24 CFR Part 3280 or, when such a standard is not applicable, the Standard for Manufactured
Home Installations ANSI / NCSBCS A225.1 or Standard for Gas Equipped Recreational Vehicles and Mobile
Housing CSA Z240.4. Ensure the unit is permanently electrically grounded to the chassis of the home.
This appliance must be securely fastened to the oor. Use the provided mounting brackets to secure the
appliance to the hearth or mobile home oor.
It is crucial that the structural integrity of the mobile home oor, wall, ceiling, and roof be maintained.
VENT RESTRICTOR
Due to the high draft produced by certain venting congurations, the vent restrictor may need to be adjusted to
ensure maximum performance. If vent restriction is necessary, it can be adjusted as follows:
1. Ensure the appliance is turned o󰀨 and is cool to touch.
2. Remove the Top Lid and set aside. (refer back to “INITIAL SETUP”)
3. Unfasten the restrictor screw from the restrictor plate and set aside.
4. Use the restrictor tab to adjust the restrictor plate to obtain desired ame hieght (will need to re
appliance to conrm ame height).
5. Once desired ame height is achieved, reinstall the restrictor screw and then the Top Lid.
RESTRICTOR
SCREW
RESTRICTOR
TAB

180-CL26.IPI.1A v2.00 May 27, 2022
Page 18 CL26.IPI.1A
INSTALLATION
AIR SHUTTER ADJUSTMENT
The air shutter allows the amount of air coming into the burner to be adjusted in order to accommodate
di󰀨erent climates and venting arrangements.
1. To access the air shutter adjustment lever, open the hinged door beneath the rebox. It is in the upper left-
hand side.
2. Start the pilot and then the burner. Allow the appliance to run for 15 minutes before making any air
adjustments.
3. The ideal ame will be blue at the base and light orange above. If the ames are short and mostly blue,
the replace is getting too much air, therefore, the air shutter should be closed until the correct ames are
achieved. To close, slide the air shutter in small increments to the right to reduce the amount of air in.
4. Flames that are very orange and have tall, dark, stringy tips are not getting enough air, therefore, the
air shutter should be opened until the correct ames are achieved. To open, slide the air shutter in small
increments to the left to increase the amount of air in.
5. When satised with the ame color, retighten air shutter lock screw.

180-CL26.IPI.1A v2.00 May 27, 2022
Page 19
CL26.IPI.1A INSTALLATION
600-584-665
PF2 IFC BOARD
135-0170 @ 18” x2
140-0294 x3
140-3611-03
WIRE BOARD CONNECTOR
GROUND
140-176-699
X4 PLUG
135-0159-B @ 2”
*BOTH ENDS
CONNECTED
INTO PLUG
Z5177.IPI
OPTIONAL
BLOWER
140-5006
BATTERY HOLDER
600.584.045
PROFLAME TRANSMITTER
PROFLAME 2 WIRING DIAGRAM

180-CL26.IPI.1A v2.00 May 27, 2022
Page 20 CL26.IPI.1A
INSTALLATION
1
2
11
7
9
4
3
8
10
12
12
12
12
12
6
5-c
885 PROFLAME VALVE
1 ON-OFF solenoid EV1 terminals
2 ON-OFF solenoid EV2 terminals
3 Inlet pressure test point
4 Outlet pressure test point
5-c Electrical pressure modulator device
6 Pressure modulator device terminal
7 Pilot adjusting screw
8 Pilot outlet
9 Gas inlet with protective seal
10 Gas outlet with protective seal
11 Ground connection
12 Mounting holes
PROFLAME VALVE SCHEMATIC