Blaze BLZ-3-NG User manual

Blaze Outdoor Products Instructional Book
Page | 1
Version 1.4
USE & CARE GUIDE
GAS GRILLS BLZ-3(NG/LP), BLZ-4(NG/LP), BLZ-5(NG/LP)
ATTENTION INSTALLER:
PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER.
ATTENTION CONSUMER:
PLEASE READ & RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE AND BEFORE INSTALLING
OR OPERATING.
- CONTACT INFORMATION -
Blaze Outdoor Products: 10920 Coursey Blvd, Baton Rouge, LA 70816 USA
Phone: [phone] email: [e-mail]
BLAZEGRILLS.COM
WARNING
I) Do not store or use gasoline or other flammable
liquids or vapor in the vicinity of this or any other
appliance
2) A LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliances.
DANGER - IF YOU SMELL GAS:
I) Shut off the gas supply to the appliance at its source.
2) Extinguish any open flames.
3) Open grill hood to release any accumulation of gas
vapor.
4) If a gas odor persists, Keep away from your
appliance and contact your gas supplier or fire
department immediately.

Blaze Outdoor Products Instructional Book
Page | 2
Version 1.4
Table of Contents
I. BBQ Specifications 4-6
II. General Safety and Installation Warnings 7
i. Location of Appliance 9
III. Electrical Safety and Installation Warnings 10
IV. Gas Safety and Installation Warnings 11
i. Checking for Gas Leaks 12-13
V. Gas Connection 14
i. Unpacking Unit 14
ii. Natural Gas Requirements 15
iii. Liquid Propane Gas and Tank Requirements 15
iv. Transporting and Storing LP Gas 16
VI. Installing the Appliance in a BBQ Island 16
i. Building BBQ Specifications 18
ii. Installation Method for Propane 19
iii. Installation Method for Natural Gas 19
VII. First Time Operation 19
i. Lighting the Appliance 20
ii. Manually Lighting the Appliance 20-21
iii. Flame Adjustment 22-23

Blaze Outdoor Products Instructional Book
Page | 3
Version 1.4
VIII. Cleaning your Appliance 22
IX. Optional Infrared Sear Burner 23
i. How to Replace Conventional Burner with Infrared Sear Burner 23
ii. Preheating the Infrared Burner 23
iii. Infrared Burner Cleaning 24
X. Fuel Conversion 24
i. Gas Regulator 24
ii. NG –LP Regulator Conversion 25
iii. Main Burner 26
iv. Rear Burner 26
XI. Warranty Registration 27
XII. Grill Parts 28-29
XIII. Product Serial Number 30
XIV.Blaze Product Registration 31

Blaze Outdoor Products Instructional Book
Page | 4
Version 1.4
THIS MANUAL APPLIES TO THE FOLLOWING BLAZE GRILLS:
Model: BLZ-4LP / BLZ-4NG 4 BURNER
Cutout Dimensions
30 5/8”W x 21 1/4”D x 8 1/2”H
BTU Output
14,000 BTU per Burner x4
Infrared Back Burner
10,000 BTU
Total BTU
68,000
Primary Ignition
Push N’ Turn Flame Thrower
Secondary Ignition
Flash Tube
Cooking Grid
Dimensions
29 1/2" X 17 7/8"
Total Cooking Area
748sq.in
(includes warming rack)
Flame Tamer
Flame Stabilizer Grid
Zone Cooking
Removable Heat Zone
Separators
Rotisserie Kit
(Motor & Forks)
Optional
Burner
Commercial Quality Cast
Stainless Steel
Gas Type
Each grill contains an NG/LP
Conversion Kit
Warranty
*Lifetime –Defects in
manufacturing and
workmanship. Cooking grids,
stainless housing as well as the
stainless burners against rust-
through.
*15 Years –Control valves
*1 Year –all other components
*Appliances must be registered
within 30 days of purchase to
validate this warranty.
*See warranty section for
details.
Model: BLZ-3LP / BLZ-3NG 3 BURNER
Cutout Dimensions
23 1/4”W x 21 1/4”D x 8 1/2”H
BTU Output
14,000 BTU per Burner x3
Infrared Back Burner
None
Total BTU
42,000
Primary Ignition
Push N’ Turn Flame Thrower
Secondary Ignition
Flash Tube
Cooking Grid
Dimensions
22 3/8" X 18"
Total Cooking Area
558sq.in
(includes warming rack)
Flame Tamer
Flame Stabilizer Grid
Zone Cooking
Removable Heat Zone
Separators
Rotisserie Kit
(Motor & Forks)
Optional (4 burner kit available
for use with this model)
Burner
Commercial Quality Cast
Stainless Steel
Gas Type
Each grill contains an NG/LP
Conversion Kit
Warranty
*Lifetime –Defects in
manufacturing and
workmanship. Cooking grids,
stainless housing as well as the
stainless burners against rust-
through.
*15 Years –Control valves
*1 Year –all other components
*Appliances must be registered
within 30 days of purchase to
validate this warranty.
*See warranty section for
details.

Blaze Outdoor Products Instructional Book
Page | 5
Version 1.4
Model: BLZ-5LP / BLZ-5NG 5 BURNER
Cutout Dimensions
38 3/8”W x 21 1/4"D x 8 1/2”H
BTU Output
14,000 BTU per Burner x5
Infrared Back Burner
10,000 BTU
Total BTU
82,000
Primary Ignition
Push N’ Turn Flame Thrower
Secondary Ignition
Flash Tube
Cooking Grid
Dimensions
37" X 18"
Total Cooking Area
915sq.in
(includes warming rack)
Flame Tamer
Flame Stabilizer Grid
Zone Cooking
Removable Heat Zone
Separators
Rotisserie Kit
(Motor & Forks)
Optional
Burner
Commercial Quality Cast
Stainless Steel
Gas Type
Each grill contains an NG/LP
Conversion Kit
Warranty
*Lifetime –Defects in
manufacturing and
workmanship. Cooking grids,
stainless housing as well as the
stainless burners against rust-
through.
*15 Years –Control valves
*1 Year –all other components
*Appliances must be registered
within 30 days of purchase to
validate this warranty.
*See warranty section for
details.

Blaze Outdoor Products Instructional Book
Page | 6
Version 1.4
BBQ SPECIFICATIONS
NOTE: “ALWAYS” have equipment measured by Contractor before building.

Blaze Outdoor Products Instructional Book
Page | 7
Version 1.4
General Safety and Installation Warnings
NOTE: The manufacturer cannot be held responsible for damage or injury caused by improper use of this
appliance.
When using your Blaze appliance, please read and follow these basic precautions:
APPLIANCE INSTALLATION
This gas appliance must be installed in accordance with all local codes.
If installation is planned in an area with no local codes, the gas appliance must be installed in accord with the
National Fuel Gas Code ANSI Z223.1 and storage and handling of liquefied petroleum gases, ANSI/NFPA 58 or
CSA B149.1 natural gas and propane installation code.
CALIFORNIA PROPOSITION 65 WARNING
The burning of gas cooking fuel generates some by-products which are on the list of substances which are
known by the State of California to cause cancer or reproductive harm. California law requires businesses to
warn customers of potential exposure to such substances. To minimize exposure to these substances, always
operate the unit according to the use and care manual, ensuring you provide good ventilation when cooking.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing
this equipment.
EXPLOSION HAZARD
Do not use the appliance as storage area for flammable materials. Keep area clear and free from combustible
materials, gasoline, and other flammable vapors and liquids. Failure to do so can result in death, explosion, or fire.
To reduce the risk of fire, electric shock, or injury, read and follow these basic precautions before
installing/operating your appliance.

Blaze Outdoor Products Instructional Book
Page | 8
Version 1.4
IMPORTANT: Consult the AHJ (Authority Having Jurisdiction) or local contractor of any uncertainty.
This unit is for outdoor use only!
Do not operate in a building, garage or any other enclosed areas. This could result in carbon monoxide buildup
which could result in injury or death.
For proper operation, burners must be aligned with the valve orifice and seated in the bracket slot. This is
accomplished by first placing the burner tube shutter hole securely over the valve orifice and then secure with
the cotter pin at the rear of the appliance.
BEWARE OF SPIDERS
CAUTION: BURNER TUBES MUST BE INSPECTED AND CLEANED BEFORE EACH USE.
Spiders and small insects occasionally spin webs or make nests in the burner tubes. These webs can lead to a gas flow obstruction, which
could result in a fire in and around the burner tubes. This type of fire is known as “FLASH-BACK” and can cause serious damage to your
appliance and create an unsafe operating condition for the user. Although an obstructed burner tube is not the only cause “FLASH-BACK”
it is the most common cause, and frequent inspection and cleaning of the burner tubes is necessary.
FOR YOUR SAFETY
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
2. Do not store any propane/butane (G31-G30) cylinder (that is not connected for use) in the vicinity of
this or any other appliance.
NOTE: Check with City and Fire department for Local Building Codes. A Permit may be
required for outdoor Kitchen Construction.

Blaze Outdoor Products Instructional Book
Page | 9
Version 1.4
Location of Appliance
Most importantly, this is an outdoor appliance. Ensure your appliance is positioned safely away from
anything that can catch fire. Under no circumstance is this appliance to be used indoors. This includes
garages or any other enclosed area.
Clearance from Combustibles: Ensure your appliance remains at a distance of at least 18” from any
combustible material such as wood, gyprock, paper and plants. Do not store combustible materials,
gasoline or flammable liquids or vapors around the appliance.
Adequate Ventilation: Ensure there is adequate ventilation for both the appliance, grill cart and/or
island cavity. This is required not only for proper combustion, but also to prevent gas build up.
Firm Level Surface: Use your appliance only on a firm level surface. This appliance is not designed for
recreational vehicles, and should not be installed on a boat or marine craft.
Protection from Weather: Keep the appliance protected from adverse weather, including rain and high
winds. Allow clear access to the entire gas supply hose and regulator.
Maintenance Access: When your appliance is installed, you should be able to access the gas supply
line including the gas piping or hose, gas regulator, gas cylinder and any shut off valves.
Partial Enclosures: Many backyards have areas that are partially closed off, such as balconies and
pergolas. In some cases, it is hard to decide whether these partially enclosed areas should be classified
as indoor areas, particularly in terms of permanent (non-closable) ventilation. Consult the AHJ (Authority
Having Jurisdiction) or local contractor of any uncertainty.
Please read all instructions before installing or operating your gas appliance to prevent injury and
appliance damage.
All gas appliances will get hot during use. Use extreme caution when operating the appliance.
Do not touch hot surfaces. Always use the handle to open or close the appliance.
Close supervision is necessary when this or any appliance is used near children. Keep children away
from the appliance during operation and until the appliance has cooled off.
Do not store any LP cylinder or tank not connected for use with the appliance, in the area of this
appliance or any other appliance. Never store an LP cylinder or tank indoors, or within the reach of
children.
Never test the appliance for gas leaks using a lighted match or any other open flame; see leak test
procedures using soap/water solutions –see section on Leak Testing.
The use of accessories, regulators, or components not recommended by the appliance manufacturer
may cause injuries and will void warranty.
Never light the appliance with the hood closed and be certain that the burners are positioned and seated
over the gas valves and on the burner support.
Never lean over the cooking surface when lighting or operating the appliance.

Blaze Outdoor Products Instructional Book
Page | 10
Version 1.4
Use cooking utensils with wood handles and insulated oven mitts when operating the appliance.
Do not store anything in the appliance. Make sure food is not forgotten in the appliance; forgotten items
could melt or catch fire when the appliance is turned on.
To prevent injuries, do not use accessories that are not recommended by the manufacturer.
Before cleaning the appliance, disconnect the rotisserie and "trip" the circuit breaker.
Never use the appliance in windy conditions. If located in a consistently windy area (oceanfront,
mountaintop, etc.) a wind break will be required. Winds blowing into or across the back hood gap, can
cause poor performance and / or cause the control panel to get dangerously hot.
Always open the appliance hood carefully, using only the handle - the hood may be hot.
Children should not be left alone or unattended in an area where any appliance is in use. They should
never be allowed to touch, sit or stand on any part of the appliance.
Do not store items of interest to children in cabinets above the appliance or in the appliance. Children
climbing on the appliance to reach these items could be seriously injured.
Wear proper clothing when operating this appliance. Loose-fitting or hanging garments should never be
worn while using the appliance.
Do not leave the appliance unattended while in use.
Do not use water on grease fires! A violent steam explosion may result. Instead, smother the fire with a
multipurpose ABC extinguisher.
Electrical Safety and Installation Warnings
Extension cords may be used if care is exercised in their use.
If an extension cord is used:
The marked electrical rating of the cord set or extension cord should be at least as great as the electrical
rating of the appliance
The cord should be arranged so that it will not touch hot surfaces, sharp edges or drape over the
countertop or tabletop (where it can be pulled or tripped over unintentionally).
Outdoor extension cords should be used with products suited for outdoor use. They are surface marked with
suffix letters "W" or "W-A" and with a tag stating "Suitable for Use with Outdoor Appliances".
To protect against electrical shock, the power cord and plug should be kept dry and off of the ground.
Do not clean this product with water spray; do not spray cleaners into the lamp socket area.
Gasoline, lighter fluid or other flammable liquids and vapors should never be stored in the area of this appliance
or any other appliance.
Before installation or service, disconnect the power supply to the work area by removing the fuse, "tripping" the
circuit breaker, or unplugging the unit.

Blaze Outdoor Products Instructional Book
Page | 11
Version 1.4
Keep any electrical supply cord and fuel supply hose away from any heated surfaces, sharp edges and dripping
grease.
Be certain your appliance is properly installed and grounded by a qualified technician in accordance with
applicable codes. To guarantee the electrical safety of this appliance, continuity must exist between the
appliance and an effective grounding system. It is imperative that this basic safety requirement be met. The
manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective
grounding system.
Do not operate any appliance with a damaged power cord or power plug, and do not operate any appliance after
the appliance malfunctions or has been damaged in any manner. If this should occur, return the appliance to the
nearest authorized service facility for examination, repair or adjustment.
Be certain your appliance is properly installed and grounded by a qualified technician in accordance with
applicable codes. To guarantee the electrical safety of this appliance, continuity must exist between the
appliance and an effective grounding system. It is imperative that this basic safety requirement be met. The
manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective
grounding system.
This appliance conforms to all uniform electrical safety codes and electrical grounding regulations. Install unit
according to I.A.W. local codes or with National Electrical Code ANSI/NFPA 70 or CSA C22.1 in their absence.
Gas Safety and Installation Warnings
Always check the Rating Plate to make sure the gas supply you are hooking up to is the gas type the
appliance is manufactured for.
Check the rating label on the left hand side of the unit.
Do not twist the gas supply hose.
Before each use, visually inspect the gas supply hose for cracks, cuts or excessive wear. Replace the
hose if necessary. Check for gas leaks.
Gas Specifications: Be sure that the gas supplied to the appliance conforms to the model you
RATING PLATE LOCATION

Blaze Outdoor Products Instructional Book
Page | 12
Version 1.4
purchased. A Natural Gas appliance requires natural gas to operate; an LP appliance requires liquid
propane gas to operate.
Never connect the appliance to an unregulated gas supply line. Appliances operated without a regulator
are unsafe and will not be serviced until installed properly and safely. Unsafe operation without a gas
regulator will void the warranty of the appliance.
Appliances operated with NG (natural gas) gas must be installed with the NG regulator supplied with the
unit and set to 4.0" water column pressure.
Appliances operated with LP (liquid propane) gas must be installed with an LP regulator set to 11" water
column pressure.
Please contact your dealer and use a licensed contractor or installer to convert your appliance to the
different gas type.
The self-contained LP system appliance is design certified to be used with a standard 20 lb., 12 1/4" diameter;
18" high cylinder with right handed connection threads and this is the maximum size LP tank to be used. The
cylinder must be marked in accordance with the latest U.S. Department of Transportation specifications for LP
gas cylinders. (DOT. CFR49 or National Standards of Canada CAN/CSA-B359 Cylinders, Spheres and Tubes for
the Transportation of Dangerous Goods) a Propane Tank with an ODP) Overfill Prevention Device) must be used
at all times.
IMPORTANT: Never connect the appliance to an unregulated gas supply.
The installation of this appliance must conform with local codes or in the absence of local codes, to the national
fuel gas code, ANSI Z223.1a-1998. Installation in Canada must be in accordance with the standard CAN/CGA-
B149.2, Propane Installation Code.
A licensed contractor or local gas company representative must perform all natural gas connections.
Ensure that the service supplying the appliance is fitted with a shut off valve conveniently positioned near the
appliance and giving ease of access.
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 0.5 psi (3.5
kPa).
The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressure in excess of 0.5 psi (3.5 kPa).
Checking for Gas Leaks
Perform a leak test at least once a year whether the gas supply cylinder has been disconnected or not. In
addition, whenever the gas cylinder is connected to the regulator or whenever any part of the gas system is
disconnected or replaced, perform a leak test.

Blaze Outdoor Products Instructional Book
Page | 13
Version 1.4
As a safety precaution, remember to always leak test your appliance outdoors in a well-ventilated area. Never
smoke or permit sources of ignition in the area while doing a leak test. Do not use a flame, such as a lighted
match to test for leaks. Use a solution of soapy water.
Prepare a leak testing solution of soapy water by mixing in a spray bottle one part liquid soap to one part
water.
Make sure all the control knobs are in the OFF position .
Turn on the gas
oOn Natural Gas systems, turn the main feed valve to the appliance.
oOn LP systems, turn the cylinder valve knob counter clockwise one turn to open.
Apply the leak-testing solution by spraying it on joints of the gas delivery system.
Blowing bubbles in the soap solution indicates that a leak is present.
Stop a leak by tightening the loose joint resealing with thread sealant or Teflon tape, removing sealant or
tape in the event of a flared connection or by replacing the faulty part with a replacement part
recommended by the manufacturer. Do not attempt to repair the cylinder valve if it is damaged. The
cylinder must be discarded to a proper LP tank location and then replaced.
Turn all control knobs back to the full OFF position.
If you are unable to stop a leak turn all control knobs back to the full OFF position, shut off the gas
supply to the appliance and release pressure in the hose and manifold by pushing in and turning any of
the control valves one quarter turn counter-clockwise.
On LP systems, remove the cylinder from the appliance.
Call an authorized gas appliance service technician or an LP gas dealer.
Do not use the appliance until the leak is corrected.

Blaze Outdoor Products Instructional Book
Page | 14
Version 1.4
Leak Testing
All gas piping and connections must be tested for leaks after installation or service. All leaks must be corrected
immediately. Remember-before exchanging an empty bottle for a new one; make sure all control valves are in
the “off” position.
Open the valve (shut-off or ‘ON’ LP tank). Test for leaks by applying liquid soap solution to all joints. Bubbles forming
indicate gas leak.
NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS.
Gas Connections
UNPACKING UNIT:
Your Blaze Series Appliance comes pre-assembled and requires very little setup. We do however; recommend
the use of professional help during the installation of your unit as improper installation may affect your warranty.
Remove the unit from the box along with all accessories and check that no damage has occurred to the unit or
any parts.
Burners: Check the burner tubes and remove any obstructions that may be in the ports or holes. Using cold
water and a brush will be sufficient. Make sure all foreign particles are removed from the burner before use.
Make sure the air shutter on the burners is slightly opened (to about 1/8" for NG and 1/4" for LP).

Blaze Outdoor Products Instructional Book
Page | 15
Version 1.4
Natural Gas Requirements
Connect a suitable natural gas flex connector to the grill regulator located on the rear right corner of the
appliance. It is recommended to use a flex connector with a minimum of a ½” diameter or larger.
Sealing all non-flared fittings with thread sealant or Teflon tape.
Check the appliance controls to ensure all control valves are in the full OFF position.
Turn on the main gas supply and check all connections for leaks using soapy water as described in the
leak testing procedure section.
Liquid Propane (LP) Gas and Tank Requirement
A collar to protect the cylinder threads on the customer supplied tank.
An arrangement for gas vapor withdrawal.
A safety relief device having direct communication with the vapor space of the cylinder.
A method of mounting.
When not in use, the tank shut off valve should be turned off.
Turn control knobs and cylinder valve to the OFF position. Unscrew valve.
Remove cylinder and have it filled at your local qualified propane dealer.
Once filled, carefully connect the valve and make sure it is secure and not leaking.
With the control knobs in the OFF position, turn on the cylinder valve.
If you smell gas or hear a hiss of gas escaping from the tank, get away from the tank and do not attempt to
correct the problem yourself. Call the Fire Department immediately.
If your appliance has no leak at the cylinder, then re-check for loose connections and retest for leaks using the
method detailed in the following pages with soapy solution.
Do not subject your LP gas cylinder to excessive heat, and always store the cylinder in an upright position.
Never store your LP cylinders indoors.
Make sure that when attaching components, all connections are secured and fully tightened to prevent leakage.
Filling and Refilling LP Gas Cylinders:
All purging and refilling of LP gas cylinders must be performed by qualified personnel in the LP gas industry.
Never store a spare LP gas cylinder under or near this appliance. Never fill the LP gas cylinder beyond 80
percent full. Failure to follow these instructions may result in explosion, personal injury or death.

Blaze Outdoor Products Instructional Book
Page | 16
Version 1.4
If one is not already available, it is recommended that an ON-OFF shutoff valve be installed at the gas supply
source, and that the gas supply be turned off when either Natural Gas or LP Gas appliances are not in use.
Transporting and Storing LP Gas
Transport only one cylinder at a time. Ensure the cylinder is secured in an upright position with the control valve
turned off and the dust cap in place. Store cylinders outdoors and out of the reach of children. Do not store
cylinders in a building, garage, or any other enclosed area.
Installing the Appliance in a BBQ Island
You will need a second person to help you avoid damaging the appliance or your appliance island.
The island must be made out of non-combustible material. In the event it is combustible, the use of an
insulation jacket is required.
Before installing an appliance in any island cut out, make sure that the opening is not bigger than the outside
frame of the appliance unit. The appliance should rest on the lip of the frame.
Pay careful attention to the location of the gas line. It should be routed away from sources of heat, sharp edges
and should make as few bends as possible.
Check to see if the gas line connection will be accessible when appliance is installed.
If the gas line connection is not easily accessible when the appliance is installed, support the appliance above
counter level and attach the gas line to the appliance. When the gas connection is made, slide the appliance into

Blaze Outdoor Products Instructional Book
Page | 17
Version 1.4
the cut out. If the gas line connection is accessible when the appliance installed, slide the appliance into the cut
out and then attach the gas line.
Be very careful not to kink the gas line when lowering the appliance into the cut out.
Keep your fingers away from where the appliance will be supported on counter. Your fingers could become
trapped and serious injury could occur.
Check to make sure the appliance is level and is supported around the entire outside edge. If the appliance is
not level or is unstable, use non-combustible shims under the outside lip to stabilize it.
Perform the leak test procedure as described earlier in this manual.

Blaze Outdoor Products Instructional Book
Page | 18
Version 1.4
BUILDING BBQ SPECIFICATIONS
MODEL
DESCRIPTION
WIDTH (A)
DEPTH (B)
HEIGHT (C)
BLZ-3
25” 3 Burner
23 1/4”
21 1/4”
8 1/2”
BLZ-4
32” 4 Burner
30 5/8”
21 1/4”
8 1/2”
BLZ-5
40” 5 Burner
38 3/8”
21 1/4”
8 1/2”
ALL BBQ ISLANDS MUST BE MANUFACTURED FROM “NON-COMBUSTIBLE” MATERIAL.
Minimum clearance to adjacent combustible construction at 14” from sides & 16” from back

Blaze Outdoor Products Instructional Book
Page | 19
Version 1.4
FIRST TIME OPERATION
Before lighting the burners inspect the gas supply piping or hose. If there is evidence of cuts, wear, or
abrasion, it must be replaced prior to use. Always keep your face and body as far away from the grill as
possible when lighting.
Caution: Never operate the appliance unattended.
Prior to using your appliance, verify that all of the following is correct:
The burner tube is free of any debris or obstruction.
Installation of the proper gas type and regulator settings.
The proper gas connection is complete.
Installation Method for Propane
Installation Method for Natural Gas

Blaze Outdoor Products Instructional Book
Page | 20
Version 1.4
Check for gas leaks.
Minimum clearances are maintained.
All packaging has been removed.
All parts and components are properly in place.
An installer-supplied manual gas shut-off valve is fully accessible.
LP hose is clean and inspected for cuts, wear, abrasion, or leaks. Replace if necessary with a suitable
UL, ETL or CSA Listed part with internally threaded connector.
Lighting the Appliance
1. Open the hood.
2. Use caution when lighting burners by standing as far away from the burners as possible.
3. To ignite burners, push the burner knob in and slowly rotate counter-clockwise to the high position.
4. You will hear a loud click as the electronic lighter produces a spark. Listen for the sound of the gas igniting
and look for a flame through the cooking grids. If the burner does not light on the first try, repeat
immediately. (For rear burner, a slower turn of the knob is necessary. This allows gas to accumulate in the
rear burner to achieve ignition.)
5. If the burner does not light in 5 seconds then wait five minutes until the gas clears before attempting to light
it again. Repeat the procedure or try the manual lighting procedure below.
6. Upon successful lighting, repeat the process on the other burners you wish to light.
7. To shut off the burners, rotate the knob and turn to OFF.
8. It is normal to hear a popping sound when the burners are turned off.
Manually Lighting the Appliance
WARNING: Do not use standard size matches or cigarette lighters to perform match-lighting procedures. Serious
burns can occur and lighters can explode.
1. Open the hood.
2. If you have just attempted to light the burner, allow five minutes for any accumulated gas to dissipate.
3. Use caution by standing as far away from the burners as possible.
4. Hold your open flam to the top of the Lighting Tube.