Blendtec A3-31E-BHMV User manual

Instruction Manual
™

Table of Contents
SECTION PAGE #
SECTION 1: IMPORTANT SAFEGUARDS 1
SECTION 2: UNPACKING 3
SECTION 3: CONNOISSEUR OVERVIEW 4
SECTION 4: INSTALLATION 6
SECTION 5: CARE AND CLEANING 10
SECTION 6: OPERATIONAL OVERVIEW 11
SECTION 7: TROUBLESHOOTING 12
SECTION 8: WARRANTY 14

CN-1
SECTION 1
IMPORTANT INFORMATION
Read all instructions carefully before using your Connoisseur™
1.1 SAFETY CERTIFICATION
The blender is certied by ETL (Report No. 3018204-
4, 3018204-2 & 3018204-3).
1.2 Connoisseur CERTIFICATION
Connoisseur and its accessories are certied by NSF
International (NSF), under the letter K (for K-TEC) in the
NSF Ofcial Listing.
1.3 AVOID CONTACT WITH MOVING PARTS
• Keep ngers, hands, hair and clothing away from all moving parts.
• Keep all utensils away from the drive socket and blender blades during
operation. Metal utensils will damage blades.
• NEVER put hands into blender jar or add substances by hand when the
blender is operating.
• NEVER place jar into drive socket if blender motor is operating.
• DO NOT rock the blender during operation.
These precautions will prevent personal injury and/or damage to the blender.
1.4 NEVER OPERATE THE BLENDER IF IT APPEARS DAMAGED
If the blender malfunctions, call your service agent rst. If it is dropped or dam-
aged in any way, return the blender to a Blendtec service agent immediately for
examination, repair, electrical or mechanical adjustment, or possible replace-
ment.
1.5 NEVER OPERATE BLENDER IN LIQUID
Do not operate the blender motor in water or any other liquid. Avoid all contact
between the motor and water. Do not use the blender outdoors where it is sub-
ject to precipitation.
1.6 NEVER PUT NON-FOOD ITEMS INTO JAR
Metal utensils, rocks and glass are dangerous if placed in jar. Damage caused
by such foreign objects will void the warranty. Keep hands and utensils out of
jar while blending to reduce the risk of severe injury to persons or damage to the
blender. Utensils may only be used when the blender is not running.
1.7 NEVER OPERATE THE BLENDER WITHOUT THE LID IN PLACE
R

CN-2
CN-3
1.8 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD
BY BLENDTEC
The use of any unauthorized attachments may cause re, electric shock, and/or
injury and will void the warranty.
1.9 CONTAINER MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS
OPERATING
1.10 BLADES ARE SHARP! HANDLE CAREFULLY!
1.11 WHEN BLENDING HOT LIQUIDS, REMOVE CENTER PIECE OF LID
1.12 POWER CORD PRECAUTIONS
• NEVER operate with a damaged cord or plug. (If the supply cord is damaged
it must be replaced by the manufacturer, or authorized service agent to avoid
a hazard
• DO NOT permit the cord to hang over the edge of the work surface.
• NEVER use an extension cord with the unit.
• Unplug the blender motor when not in use; before changing blender loca-
tions; or cleaning.
1.13 NEVER ATTEMPT TO REPAIR THE POWER UNIT
Never remove the blender motor cover. The blender motor does not contain self-
adjustable or serviceable parts. A qualied service agent must make all service
adjustments. Removing the cover or attempting to service the blender will void
the warranty.
1.14 TURN THE POWER SWITCH OFF WHEN NOT IN USE
The Power Switch (ON/OFF switch) is located on the front panel of the blender
motor cover.
1.15 AVOID TOUCHING THE BLENDER DRIVE SOCKET AFTER EXTENSIVE
USE.
The blender drive socket may become hot after numerous cycles.
1.16 CLOSE SUPERVISION IS NECESSARY WHEN APPLIANCE IS USED BY
OR NEAR CHILDREN.
1.17 THE CONNOISSEUR IS INTENDED FOR HOME USE ONLY! ANY USE
OF THE CONNOISSEUR FOR COMMERCIAL PURPOSES VOIDS ALL WAR-
RANTIES.
SAVE THESE INSTRUCTIONS
SECTION 2
SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE
USE.
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• ConnoisseurTM motor base
• Black motor stand
• 64 oz blender jar with lid (marked to 32 ounces)
• 96 oz blender jar with lid (marked to 48 ounces)
• Recipe book
1. Remove blender motor, blender jar and lid from packaging.
2. Unwind the power cord.
3. Check for any packing material that may have blocked ventilation holes in
the blender motor.
4. Inspect all items to ensure no damage occurred in shipment.
5. If any damage has occurred contact your Blendtec service agent
immediately.
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE
Record your blender motor serial number and date of purchase in the space
below. You will need these when contacting Blendtec for service or questions.
Motor Serial #:
____________________________________________________
(Found on bottom of motor base)
Date of Purchase:
____________________________________________________
Purchased From:
____________________________________________________
2.3 REGISTRATION OF YOUR BLENDER
Register online at www.blendtec.com (select “Product Registration”
under the ‘Support’ button) or return the registration card to the address provided.

CN-4
CN-5
SECTION 3
Connoisseur Overview
(Refer to Figures 1 and 2)
3.1 BLENDER MOTOR
• Blender base housing: houses the power unit in a surgical stainless steel cas-
ing. Never remove the blender base cover. Removal of the cover will void
the warranty.
• Touch Pad: Consists of six buttons that contain pre-programmed settings for
selective blender control, a pulse button, and two speed control buttons.
• LCD Information Center: will indicate status of unit as well as overload or
over-temperature conditions.
• Power Unit: This unit is located within the blender motor and contains the
machinery that runs the blender.
• Power Switch: Located on the front panel underneath the LCD display.
3.2 BLENDER JAR ASSEMBLY
The blender jar assembly consists of the blender jar, blade assembly, and lid.
• Jar: Made from polycarbonate to provide maximum efciency and clear
visibility of blender performance.
• Blade Assembly: Stainless steel designed to provide fast consistent blending
3.3 POWER SPECIFICATIONS
The Connoisseur is made for 110/120 volts circuits only. It is rated at
13 amps/1500 watts. It is highly recommended that this unit be protected by a
15 amp circuit breaker or fuse.
FIGURE 4 - Motor Base - Top View
FIGURE 1 - Motor Base and Jar - Front View
Lid
Jar
Blade Assembly
Motor Base
LCD Diplay
Power Switch
Drive Socket
Touchpad

CN-6
CN-7
16 /”
6 /”
8 ¼”
SECTION 4
INSTALLATION
It is recommended that surge protection be placed between the receptacle and
the blender motor.
4.1 CONNOISSEUR ABOVE COUNTER INSTALLATION
1. Place motor into base unit.
2. Place blender on a at, clean and dry surface.
3. Make sure a plug outlet is available within four feet of the blender motor.
4. Ensure that the unit is turned off before plugging it into a separate 120-volt
receptacle.
5. Ensure that blender vents are unobstructed to allow proper cooling during
use.
FIGURE 3 - Above-Counter Dimensions

CN-8
CN-9
4.2 CONNOISSEUR IN-COUNTER INSTALLATION
Preparation
1. Identify desired blender location. Consider preferences such as proximity to
ingredients, available counter space, and access to a power source.
(A licensed electrician may need to install appropriate power source for the
blender.)
2. Ensure potential site meets all dimensional requirements (See Figure 4.)
• Countertop can be no thicker than 3/4 inch (19 mm). A countertop thicker
than 3/4 inch will obstruct ventilation louvers on the upper sides of the
blender base.
• If installing more than one blender, allow 14-16 inches (356-406 mm) center-
to-center blender spacing.
NOTE: The blender unit draws ambient air into the louvers located on the bottom
of the blender base. It then evacuates hot air through the louvers located on the
upper sides of the blender base. Ensure a sufcient amount of air circulates be-
neath the blender base to allow cooling. Hot air should not be trapped beneath
the counter top. Nothing should be stored closer than 3 inches (76mm) from the
bottom of the blender motor.
3. Cut a hole in the counter top 4 3/8 inches (111 mm) wide and 5 7/8 inches (149
mm) long with the shorter side facing the operator. (See Figure 4). Make sure
all space requirements and measurements are correct BEFORE cutting.
Depending on the type and style of your counter top, different types of
equipment may be needed to cut the appropriate hole. It is always recom-
mended to consult with a professional before cutting.
Installation In Counter
1. Ensure that an electrical receptacle is readily accessible when you locate the
equipment.
2. Slide the blender base into the hole cut in your counter top (per instructions
above) with the LCD indicator and touchpad facing the operator side of the coun-
ter top. The formed rubber gasket on the rim of the motor base should t into the
hole and rest lightly on the counter top.
3. Make sure the power switch is off before plugging the unit into the wall. Plug
the unit into a separate 120 volt receptacle with 15 amp protection.
FIGURE 4 - In-Counter Installation

CN-10
CN-11
SECTION 5
CARE AND CLEANING
5.1 AFTER USE CLEANING
1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender
jar.
2. Place the lid tightly onto the jar. Place the blender jar on the blender base,
and with your hand placed on top of the lid; press the pulse button for 5
seconds.
3. Rinse with clear water until all soap is rinsed from jar and lid.
4. Clean the blender base by simply wiping the base and touchpad with a
damp rag and water.
5.2 LONG-TERM SANITATION
1. For long-term sanitation, occasionally ll the blender jar half way with hot
water.
2. Add one teaspoon of liquid chlorine bleach.
3. Stir for 10 seconds to mix water and bleach. Let mixture stand in blender jar
for ve minutes.
4. Empty water/bleach mixture and rinse the jar thoroughly to ensure that there
is no bleach mixture left in the jar. Turn jar RIGHT SIDE UP on dish rack
until dry.
5.3 CLEANING TIPS AND CAUTIONS
• Do not use abrasives or stiff brushes to clean the blender base or jar as this
will dull or scratch the surface. Cosmetic damage is not covered by war-
ranty.
• NEVER submerge the blender motor in water. Avoid submerging blender jars
for more than 5 minutes. Water penetration through the lower jar seals will
reduce the life of the jar. After cleaning, we recommend the blender jar be
stored upright.
• BLENDER JAR IS DISHWASHER SAFE - TOP RACK ONLY! Extreme tem-
peratures damage the lower seal to the jar.
SECTION 6
OPERATIONAL OVERVIEW
6.1 MAIN POINTS OF OPERATION
1. Turn on the main power switch located on the front of the blender motor.
2. Place the blender jar on the base, making sure the jar is secure. Attach the
blender lid.
3. Press the desired touch pad button once. You may press any button on the
lower row to stop the cycle.
4. When cycle is complete, remove the blender jar and serve.
6.2 AUTOMATIC CYCLE OPERATION
The Blendtec Connoisseur has blending cycles for ice cream, frozen yogurt, ice
crushing, milkshakes, soups, syrups, fondues, sauces, dips, dressings, batters,
whole juice, and smoothies. These cycles have variable speed settings that will
change during the course of the cycle. This allows the blender to draw the con-
tents into the blending vortex, which creates the desired texture. The blender will
run its pre-programmed cycle and automatically shut off. If at any point you want
to stop the blender before it has completed its cycle, press any lower row button.
Note: The speed buttons allow you to control the blender to operate up to 10
speed settings. Simply press the speed up button and the motor will begin.
Continue pressing the Speed Up key to increase the speed, or press the Speed
Down key at any time to decrease speed. Once you have reached the desired
speed, release the button. Once you press a speed button, the blender will begin
to run the selected speed, then shut off after 50 seconds. To stop the cycle be-
fore the 50 seconds, press any button on the lower row.

CN-12
CN-13
SECTION 7
TROUBLESHOOTING
7.1 BLENDER MOTOR WILL NOT TURN ON
If the blender motor will not turn on, try the following:
• Make sure the main power switch on the front panel is turned ON.
• Check your house circuit breaker switch or fuse to make sure it is set to the
ON position.
• Unplug the power cord from the wall receptacle, wait 5 seconds, then plug
power cord back in.
• Determine if the Liquid Crystal Display (LCD) is lit. An absence of a lit LCD
indicates a lack of power to the unit.
• Remove the blender jar from the blender motor and check to make sure the
blade turns freely while unattached to the motor. If the blade does not move
freely the problem may be the jar, not the motor. Check the jar by turning the
shaft by hand to see if it rotates easily.
Look at the LCD:
• A reading of “OVERTEMP” indicates that the motor is overheating. The
blender has been disabled until the unit cools to operating temperatures.
Turn off and unplug the unit. Allow it to cool for at least 20 minutes.
• A reading of “OVERLOAD” indicates an overload on the motor. Turn off
and unplug the unit. Plug in the unit and turn the motor on again to clear the
overload condition. Check the blender jar for blockage. If overload condition
re-occurs, contact your Blendtec service agent.
• Blade stops: If the overload switch stops the blender, remove the blender
jar and carefully check for blockage of the blade. If no blockage is found,
replace jar and use the Pulse button on the touch pad to quickly pulse the
blade through the mixture. Once the blade spins freely a programmed but-
ton may be used.
7.2 NOISE LEVEL CHANGES
If the blender noise level has increased signicantly from original levels, deter-
mine whether the sound is coming from the blender motor or jar.
• Blender Motor: Check to see if the excess noise is coming from the blender
base. Remove the jar and press cycle number two or three. Listen to the
motor sound without a jar attached. If it is excessively noisy contact your
Blendtec service center.
• Jar: Check to see if the excess noise is coming from the jar. Place the jar
back on the motor. Run the motor for a few seconds using the Pulse button.
If you have more than one jar, test a different jar to determine whether the
sound changes as different jars are used. If a jar is excessively noisy, or if
the blade assembly seems loose or sounds “gravelly” when turned by hand,
contact your Blendtec service center.
7.3 BLENDED TEXTURE UNSATISFACTORY
If the blended texture of product is lumpy or uneven, do the following:
• Ensure the mixture is not cavitating during the cycle. Cavitation is a condi-
tion in which the blender blade spins freely in an air pocket within the drink
mix because the mix is too cold or too solid. This problem can be corrected
by increasing the mix temperature by reducing ice, increasing liquid and/or
ensuring that the frozen ingredients used in the recipe are never colder than
10 degrees Fahrenheit (-12 degrees Celsius).
• Increase cycle time. If the drink is mixing well but has not had enough time
for complete blending hold the “Pulse” button for required extra blending
time.
• TRIED EVERYTHING? If none of the preceding suggestions work, contact
your Blendtec service agent for further assistance.
INSTRUCTIONS THAT APPEAR IN THIS USER
GUIDE ARE NOT MEANT TO COVER EVERY
POSSIBLE CONDITION OR SITUATION THAT
MAY OCCUR. GOOD JUDGMENT MUST BE
USED WHEN OPERATING THIS OR ANY OTHER
MACHINERY.

CN-14
CN-15
SECTION 8
WARRANTY
WARRANTY DESCRIPTION (US Domestic and Canada)
Your Blendtec Connoisseur motor is warrented for 5 years. The jar assembly,
including all moving jar parts, is covered against leaking or breakage for 1 year.
The blender jar blade and the motor base drive socket are covered by a lifetime
warranty. Warranties begin from date of purchase.
The quality of Blendtec blenders are unsurpassed. You will enjoy years of won-
derful and reliable service from your Blendtec Connoisseur.
Warranties begin from the date of purchase. Cosmetic damage, product abuse,
unreasonable use, damage resulting from an accident, product tampering, servic-
ing performed or attempted by unauthorized service agencies, units that have
modications, or have been or used for commercial purposes are not included
under this warranty.
THIS WARRANTY APPLIES ONLY TO PRODUCTS SOLD BY
BLENDTEC OR ITS AUTHORIZED DEALERS
Limited FIVE Year Warranty
Blendtec warrants the Connoisseur motor to be free of defect in material and
workmanship for a period of ve years. During this period, such defects will be
repaired or the product replaced, at Blendtec’s discretion, without charge. This
warranty does not cover damage caused by misuse, accident, or negligence. All
implied warranties, including but not limited to implied warranties of tness and
merchantability are limited in duration to a period of ve years on motor and one
year on jars. Any unit submitted for repair must be accompanied by proof
of original purchase and should be shipped prepaid to:
Blendtec home
1206 South 1680 West
Orem, UT 84058
Toll Free: [phone]
Local: [phone]
FOR QUESTIONS REGARDING THIS WARRANTY
CONTACT CUSTOMER SERVICE AT
[phone] OR [phone].
UNDER WARRANTY
1. Contact Blendtec immediately to diagnose the difculty. Please have blender
serial number ready as well as a description of the problem. Do not attempt to
do your own repairs. Repairs made by persons other than Blendtec authorized
service representatives will void the warranty. Many issues can be resolved
simply and quickly over the phone.
2. If the difculty cannot be resolved over the phone, your unit may require
replacement. If the blender is under warranty, Blendtec will repair or replace the
unit at no cost. Cosmetic damage and abuse are not included.
3. Upon receiving instructions from Blendtec, box up your existing unit and en-
close the following:
Your name:
Address:
Phone number:
The blender serial number:
(located on the bottom of the blender motor base)
Cycle Count (from the LCD indicator):
Your purchase date: Place of purchase:
An explanation of the problem:
OUT OF WARRANTY
1. Contact Blendtec to diagnose the difculty. Please have the blender serial
number ready along with a description of the problem. Do not attempt to do your
own repairs. Many issues can be resolved simply and quickly over the phone.
2. If the blender is not under warranty and you wish to have it repaired, box up
the blender motor and ship it to Blendtec. You will be billed for services rendered.
3. When you ship your unit please enclose the following:
Your name:
Address:
Phone number:
The blender serial number:
(located on the bottom of the blender base)
Cycle Count (from the LCD indicator):
Your purchase date: Place of purchase:
An explanation of the problem:

1206 South 1680 West
Orem, UT 84058
801-222-0888
blendtec.com
MKT-RE-MN-091 Blendtec Home Connoisseur Manual Rev. 02 June 2006
©2006 K-TEC, Inc., All Rights Reserved
Blendtec is a registered trademark of K-TEC, Inc.