Blizzard StormChaser Supercell User manual

Blizzard Lighting, LLC
http://www.blizzardpro.com
Waukesha, WI USA
Copyright (c) 2020

Page 2
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
TABLE OF CONTENTS
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of the Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions 4
2. Meet the StormChaser™ Supercell 5
Main Features 5
DMX Quick Reference (7/20/52-Channel Modes) 5
StormChaser™ Supercell Pin-Up Picture 6
The Rear Connections 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch of StormChaser™ Supercells 7
Data/DMX Cabling 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh?!? 8
Take It To The Next Level: Setting Up DMX Control 8
Fixture Linking (M/S Mode) 9
Lens Installation 9
Mounting & Rigging 9
4. Operating Adjustments 10
The Control Panel 10
Control Panel Menu Structure 11
Section Identication 11
DMX Mode 12
Starting DMX Address 12
DMX Channel Mode 12
M/S Mode 12
Auto Mode, Sound Active, & Manual Adjustments 12
Auto Programs 12
Sound Active Mode 12
Preset and Manual Colors 12
DMX Values In-Depth 13
Auto Mode Channel Values 13
5. Appendix 14
Keeping Your StormChaser™ Supercell As Good As New 14
Returns (Gasp!) 14
Shipping Issues 14
Tech Specs! 15
Dimensional Drawings 15

Page 3
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x StormChaser™ Supercell
• 1 x PowerCON-Compatible Power Cord
• 3 x Lenses: Frosted (installed), Clear, and Opaque
• A Set of Mounting Brackets + Knobs
• This Lovely User Manual
Getting It Out Of the Box
Congratulations on purchasing one way cool, way exible, way original LED strip
light! Now that you’ve got your StormChaser™ Supercell, you should carefully
unpack the box and check the contents to ensure that all parts are present and
in good condition. If anything looks as if it has been damaged in transit, notify
the shipper immediately and keep the packing material for inspection. Again,
please save the carton and all packing materials. If a xture must be returned
to the factory, it is important that the xture be returned in the original factory
box and packing.
Powering Up!
All xtures must be powered directly o a switched circuit and cannot be run
o a rheostat (variable resistor) or dimmer circuit, even if the rheostat
or dimmer channel is used solely for a 0% to 100% switch.
Warning! All xtures must be connected to circuits with a suitable
Ground (Earthing).
Getting A Hold Of Us
If something happens goes wrong, please visit www.blizzardpro.com/
support and open a support ticket. We’ll be happy to help, honest.
Disclaimer: The information and specications contained in this document are
subject to change without notice. Blizzard Lighting™ assumes no responsibility
or liability for any errors or omissions that may appear in this user manual.
Blizzard Lighting™ reserves the right to update the existing document or to
create a new document to correct any errors or omissions at any time. You can
download the latest version of this document from www.blizzardpro.com.
Author: Date: Last Edited: Date:
J. Thomas 8/11/2020 J. Thomas 9/9/2020

Page 4
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Please read these instructions carefully. They include
important information about the installation, usage and
maintenance of this product.
Safety Instructions
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de-
cal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
head. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs yourself. In the unlikely event your unit may
require service, please open a support ticket at www.blizzardpro.com/support.

Page 5
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
2. MEET THE STORMCHASER™ SUPERCELL
Main Features
• Color mixing via 224x 5050RGB/0.2W LEDs
• 16 individually controllable cells
• 59 built-in auto/sound active macros w/speed control
• Auto and sound active programs via DMX
• Variable electronic strobe
• 5V USB to power SoC-It™ wireless unit (not included)
• Flicker-free (10KHz PWM) dimming
• Built-in microphone
• Dual mounting brackets
• Includes 3 lenses (frosted, opaque, and clear)
Control
• Protocol: USITT DMX-512
• DMX channels: 7/20/52-channels
• Easy-to-use 4-button control panel with LED display
• Operating modes: DMX512, M/S, auto mode, sound active, RDM
DMX Quick Reference (7/20/52-Channel Modes)
7CH 20CH 52CH What It Does
1 1 1 Dimmer
2 2 2 Strobe
-- 3-18 -- Section 1-16 Color Presets
-- -- 3-50 Section 1-16 R/G/B Intensity (0% <--> 100%)
3 -- -- Red Intensity (0% <--> 100%)
4 -- -- Green Intensity (0% <--> 100%)
5 -- -- Blue Intensity (0% <--> 100%)
6 19 51 Auto (008-247) + Sound Active (248-255)
7 20 52 Auto Speed (slow <--> fast)

Page 6
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
The Rear Connections
StormChaser™ Supercell Pin-Up Picture
Mounting Bracket
& Locking Knob
224x 5050RGB/0.2W
LED Light Source
Power
Out
POWER IN
DMX IN
USB
MENU
MIC
ENTER
POWER OUT
+5V,700ma
DMX OUT
Right End
4-Button
Control Panel
DMX
In
Power
In
DMX
Out
POWER IN
DMX IN
USB
MENU
MIC
ENTER
POWER OUT
+5V,700ma
DMX OUT
5V
USB
Left End
Lens Cover (Includes Frosted,
Clear, and Opaque)
Mounting Bracket
& Locking Knob

Page 7
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Fuse Replacement
The StormChaser™ Supercell utilizes a high-output switch-mode power supply
with an internal fuse. Under normal operating conditions, the fuse should not
require replacement. The fuse is eld replaceable, however it is an advanced
procedure suited to qualied individuals. Should the fuse require replacement,
please contact Blizzard Lighting for instructions, or to return your unit for
service.
Connecting A Bunch of StormChaser™ Supercells
You will need a serial data link to run light shows using a DMX-512 controller
or to run shows on two or more xtures set to sync in master/slave operating
mode. The combined number of channels required by all the xtures on a serial
data link determines the number of xtures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. Also,
connecting more than 32 xtures on one serial data link without the use of a
DMX optically-isolated splitter may result in deterioration of the digital DMX
signal. The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of xtures on a serial data link is 32
xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-grade
cables that can carry a high quality signal and are less prone to electromagnetic
interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but note that
they cannot transmit DMX data as reliably over long distances. In any event,
the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Before replacing a fuse, disconnect the power cord.
ALWAYS replace with the same type and rating of fuse.
3. SETUP

Page 8
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR connec-
tor on the other end. (Duh!)
To build your own DMX Terminator:
Obtain a 120-ohm, 1/4-watt resistor, and wire it between pins 2 & 3 of the last xture. They are also
readily available from specialty retailers.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the DMX cable to the female connector
(output) on the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connector
(input).
Note: It doesn’t matter which xture address is the rst one
connected. We recommend connecting the xtures in terms
of their proximity to the controller, rather than connecting the
lowest xture number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture to
ensure best communication.
CAUTION: Do not allow contact between the common and the xture’s chassis
ground. Grounding the common can cause a ground loop, and your xture may
perform erratically. Test cables with an ohm meter to verify correct polarity and
to make sure the pins are not grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter. If
you’d like to build your own, the chart below details a proper cable conversion:
Conductor 3-Pin Female (Output) 5-Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data 1- (Primary Data Link) Pin 2 Pin 2
Data 1+ (Primary Data Link) Pin 3 Pin 3
Data 2- (Optional Secondary Data Link) Pin 4 Pin 4
Data 2+ (Optional Secondary Data Link) Pin 5 Pin 5
12
33
INPUT OUTPUT
Common
DMX +
DMX -
DMX OUTDMX IN
First
Fixture
in Chain
Next
Fixture
in Chain
DMX OUTDMX IN
A Word on Termination:
DMX is a resilient communication protocol, however
errors still occasionally occur. Termination reduces signal
errors, and therefore best practices include use of a
terminator in all circumstances. If you are experiencing
problems with erratic xture behavior, especially over
long signal cable runs, a terminator may help improve
performance.

Page 9
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Fixture Linking (M/S Mode)
1. Connect the male connector side of the DMX cable to the output female
connector of the rst xture.
2. Connect the end of the cable coming from
the rst xture which will have a female
connector to the input connector of the next
xture consisting of a male connector. Then,
proceed to connect from the output as stated
above to the input of the following xture
and so on.
A quick note: Often, the setup for Master-Slave and
Standalone operation requires that the rst xture in the
chain be initialized for this purpose via either settings in the
control panel or DIP-switches. Secondarily, the xtures that
follow may also require a slave setting.
Check the “Operating Adjustments” section in this manual for complete
instructions for this type of setup and conguration.
DMX OUTDMX IN
First
Fixture
in Chain
Next
Fixture
in Chain
DMX OUTDMX IN
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is enough
room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the xture
using a suitable “C” or “O” type clamp. The clamp should be rated to hold at
least 10x the xture’s weight to ensure structural stability. Do not mount to
surfaces with unknown strength, and ensure properly “rated” rigging is used
when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the xture.
After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
Lens Installation
To replace the lens, follow these steps:
1. Remove the locking knob, bracket, 4 screws,
and end cap on either of the two ends.
2. Loosening the screws on the opposite end can
allow the lens to slide easier, if needed.
3. Slide the existing lens out, and slide the
replacement lens in.
4. Reinstall the end cap, 4 screws, bracket, and
locking knob.

Page 10
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
The control panel LED display shows the menu items you select from the menu
map on page #11. When a menu function is selected, the display will show im-
mediately the rst available option for the selected menu function. To select a
menu item, press <ENTER>.
Use the <UP> and <DOWN> buttons to navigate the menu options. Press the
<ENTER> button to select the menu function currently displayed, or to enable
a menu option. To return to the previous option or menu without changing the
value, press the <MENU> button.
4. OPERATING ADJUSTMENTS
The Control Panel
All the features and dierent modes possible with the StormChaser™ Supercell
are accessed by using the control panel on the rear of the xture. There are 4
control buttons under to the LED display which allow you to navigate through
the various control panel menus.
<MENU>
Is used to navigate to the previous higher-level menu item.
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
<ENTER>
Is used to select and conrm/store the current selection.

Page 11
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Control Panel Menu Structure
Addr A001 - A512 To choose the starting DMX address
ChNd 7ch To run in 7-channel mode
20ch To run in 20-channel mode
52ch To run in 52-channel mode
Node NaSt Set as master xture
DMX-512 DMX mode (slave)
SoUn Su 0 - Su59 Sound active (0 = cycles 1-59)
Se00 - Se99 Decrease/increase mic sensitivity level
Auto Au 0 - Au59 Auto mode (0 = cycles 1-59)
SP 1 - Sp 9 Speed adjustment (slow <--> fast)
CoLo
(preset colors)
Co 1 Red
Co 2 Green
Co 3 Blue
Co 4 Yellow
Co 5 Magenta
Co 6 Cyan
Co 7 White
Nanu
(manual colors)
Red Red Intensity (0% <--> 100%)
Blue Green Intensity (0% <--> 100%)
Green Blue Intensity (0% <--> 100%)
dISP <ENTER> Display Invert
Ver V10 Software Version
Section Identication
16 15 14 13 12 11 10 9
87654321
Left
Right
These sections (cells) are used with the eects in 20CH DMX mode (channels
3-18), and color mixing in 52CH DMX mode (channels 3-50).
The table below depicts an overhead view of the StormChaser™ Supercell, and
it shows the identication numbers of the 16 LED sections.
Front
Back

Page 12
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
Starting DMX Address:
1.) Navigate the main menu until you reach Addr, and press the
<ENTER> button. Then use the <UP/DOWN> buttons to select a
starting DMX address ranging from 1-512, and press <ENTER>.
DMX Channel Mode:
1.) Navigate the main menu until you reach ChNd, and press the
<ENTER> button. Then use the <UP/DOWN> buttons to select 7ch,
20ch, or 52ch, and press the <ENTER> button to conrm.
M/S Mode:
1.) Daisy chain the DMX input/output connections of the xtures.
2.) On the 1st xture, navigate to Node and press <ENTER>.
3.) Then highlight NaSt, and then press the <ENTER> button.
4.) On following xtures, this setting should be set as DMX-512.
Auto Mode, Sound Active, & Manual Adjustments
Allows a single or daisy chained units to run factory installed programs.
Auto Programs:
1.) Navigate the menu until you reach Auto, and press <ENTER>.
2.) Use the <UP/DOWN> buttons to highlight Au 0 - Au59, and press
<ENTER> ("Au 0" cycles through all programs).
3.) Then use the <UP/DOWN> buttons to highlight a speed setting
from SP 1 - SP 9 (slow <-> fast).
4.) Press <ENTER>, and the program will start shortly.
Sound Active Mode:
1.) Navigate the menu until you reach SoUn, and press <ENTER>.
2.) Use the <UP/DOWN> buttons to Highlight Su-- (program), or Se--
(sensitivity), and press <ENTER>.
3.) To select a program, use the <UP/DOWN> buttons to select Su 0 -
Su59, and press <ENTER> ("Su 0" cycles through all programs).
4.) To adjust mic sensitivity, use the <UP/DOWN> buttons to select
from Se00 - Se99 (decrease <-> increase).
5.) Press <ENTER>, and the program will start shortly.
Preset and Manual Colors:
1.) Navigate to CoLo (preset) or Nanu (manual), and press <ENTER>.
2.) For preset colors, highlight Co 1 - Co 7 and press <ENTER>.
3.) For manual color mixing, adjust the Red, Green, and Blue intensity
levels from 0-255, and press the <ENTER> button.

Page 13
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
DMX Values In-Depth (7/20/52-Channel Modes)
7CH 20CH 52CH Value What It Does
1 1 1 0-255 Dimmer
2 2 2 0-255 Strobe
-- 3 -- 0-255 Cell 1 Eects:
000-015 No Function
016-031 Red
032-047 Green
048-063 Blue
064-079 Yellow
080-095 Lime
096-111 Orange
112-127 Purple
128-143 Magenta
144-159 Pink
160-175 Med. Blue
176-191 Aqua
192-207 Lt. Blue
208-255 White
-- 4 -- 0-255 Cell 2
-- 5 -- 0-255 Cell 3
-- 6 -- 0-255 Cell 4
-- 7 -- 0-255 Cell 5
-- 8 -- 0-255 Cell 6
-- 9 -- 0-255 Cell 7
-- 10 -- 0-255 Cell 8
-- 11 -- 0-255 Cell 9
-- 12 -- 0-255 Cell 10
-- 13 -- 0-255 Cell 11
-- 14 -- 0-255 Cell 12
-- 15 -- 0-255 Cell 13
-- 16 -- 0-255 Cell 14
-- 17 -- 0-255 Cell 15
-- 18 -- 0-255 Cell 16
-- -- 3-50 0-255 Individual Cell 1-16, R/G/B Intensity
-- -- CH Cell CH Cell CH Cell CH Cell
-- -- 3 1R 15 5R 27 9R 39 13R
-- -- 4 1G 16 5G 28 9G 40 13G
-- -- 5 1B 17 5B 29 9B 41 13B
-- -- 6 2R 18 6R 30 10R 42 14R
-- -- 7 2G 19 6G 31 10G 43 14G
-- -- 8 2B 20 6B 32 10B 44 14B
-- -- 9 3R 21 7R 33 11R 45 15R
-- -- 10 3G 22 7G 34 11G 46 15G
-- -- 11 3B 23 7B 35 11B 47 15B
-- -- 12 4R 24 8R 36 12R 48 16R
-- -- 13 4G 25 8G 37 12G 49 16G
-- -- 14 4B 26 8B 38 12B 50 16B
3 -- -- 0-255 Red Intensity (0% <--> 100%)
4 -- -- 0-255 Green Intensity (0% <--> 100%)
5 -- -- 0-255 Blue Intensity (0% <--> 100%)
6 19 51 0-007 No Function
8-255 Auto Chase & Sound Active (see table below)
7 20 52 0-255 Auto Speed (slow <--> fast)
Auto Mode Channel Values (6/19/51)
Chase 1 008-012 Chase 21 089 Chase 41 167-170
Chase 2 013-016 Chase 22 090-093 Chase 42 171-174
Chase 3 017-020 Chase 23 094-097 Chase 43 175-178
Chase 4 021-024 Chase 24 098-101 Chase 44 179-182
Chase 5 025-028 Chase 25 102-105 Chase 45 183-186
Chase 6 029-032 Chase 26 106-109 Chase 46 187-190
Chase 7 033-036 Chase 27 110-113 Chase 47 191-194
Chase 8 037-040 Chase 28 114-117 Chase 48 195-198
Chase 9 041-044 Chase 29 118-121 Chase 49 199-202
Chase 10 045-048 Chase 30 122-125 Chase 50 203-206
Chase 11 049-052 Chase 31 126-129 Chase 51 207-210
Chase 12 053-056 Chase 32 130-133 Chase 52 211-214
Chase 13 057-060 Chase 33 134-137 Chase 53 215-218
Chase 14 061-064 Chase 34 138-141 Chase 54 219-226
Chase 15 065-068 Chase 35 142-145 Chase 55 227-231
Chase 16 069-072 Chase 36 146-149 Chase 56 232-235
Chase 17 073-076 Chase 37 150-153 Chase 57 236-239
Chase 18 077-080 Chase 38 154-158 Chase 58 240-243
Chase 19 081-084 Chase 39 159-162 Chase 59 244-247
Chase 20 085-088 Chase 40 163-166 Sound Active 248-255

Page 14
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Keeping Your StormChaser™ Supercell As Good As New
The xture you’ve received is a rugged, tough piece of pro lighting equipment,
and as long as you take care of it, it will take care of you. That said, you’ll need
to take care of it if you want it to operate as designed. You should keep the
xture clean, especially if you are using it in an environment with a lot of dust,
fog, haze, wild animals, wild teenagers or spilled drinks.
Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the xture running cool and prevent damage from overheating.
In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
xtures.
Common sense and taking care of your xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your
client’s satisfaction and “wow factor.” That’s what it’s all about, after all!
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But,
like any complex piece of equipment designed and built by humans, once in a
while, something doesn’t go as planned. If you nd yourself with a xture that
isn’t behaving like a good little xture should, you’ll need to obtain a Return
Authorization (RA).
Don’t worry, this is easy. Just visit www.blizzardpro.com/support and open a
support ticket, and we’ll issue you an RA. Then, you’ll need to send the unit to
us using a trackable, pre-paid freight method. We suggest using USPS Priority
or UPS. Make sure you carefully pack the xture for transit, and whenever
possible, use the original box & packing for shipping.
When returning your xture for service, be sure to include the following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We will, at our discretion, repair or replace the xture. Please remember
that any shipping damage which occurs in transit to us is the customer’s
responsibility, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.
5. APPENDIX

Page 15
StormChaser™ Supercell Rev. A © 2020 Blizzard Lighting, LLC
Tech Specs!
Weight & Dimensions
Width 42.8 in (1085 mm)
Depth 2.6 in (66 mm)
Height 3.3 in (82 mm)
Weight 3.2 Lbs. (1.45 kg)
Power
Operating Voltage 100-240VAC, 50-60 Hz
Power Consumption 40W
USB 5V (700ma)
Light Source
LED 224x 5050RGB/0.2W LEDs
Luminance Clear Filter Frosted Filter Opaque Filter
3,958 Nits 1,049 Nits 55 Nits
Thermal
Max. Operating Temp. 104 degrees F (40 degrees C) ambient
Control
Protocol USITT DMX-512
DMX Channels 7/20/52-channel
Input/Output 3-pin XLR Male/Female
Other Operating
Modes DMX512, M/S, Auto, Sound Active
Warranty
2-year limited warranty, does not cover malfunction
caused by damage to LEDs.
Dimensional Drawings
42.8 in (1085 mm)
3.3 in (82 mm)
2.6 in (66 mm)
2.5 in (64 mm)

Enjoy your product!
Our sincerest thanks for your purchase!
--The team @ Blizzard Lighting